Question about Jeep Cars & Trucks

1 Answer

How much does hub assembly cost for 1994 jeep grand Cherokee?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Jeep Master
  • 796 Answers

Call the auto parts store to find out! Advanced Auto, Auto zone, ETC, God-Bless!

Posted on Apr 09, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 1994 Grand Cherokee Jeep wont start

It is likely one of your battery cables loose. Same thing just happened to me today. What you need to do is first lock the doors, and close them. Then you need to disconnect, and reconnect the battery cable, then if the security lights still blink you must use your key to unlock the door, then it should stop blinking, and start just fine.

Posted on Jun 02, 2009

  • 67 Answers

SOURCE: 2001 Jeep Grand Cherokee 4.7L crank no start

easy trouble shoot easy fix ! check to see if its getting fire if not replace the crank sensor it will fire right up common problem with the jeeps . Hope this helps you out !!!

Posted on Jun 02, 2009

  • 90 Answers

SOURCE: HOW TO REMOVE HEADLIGHT ASSEMBLY 2006 JEEP GRAND CHEROKEE

remove the 7mm bolt in the centre top of lamp unit then with a big screwdriver just behind headlamp prise outwards quite firmly

Posted on Jul 03, 2009

ZJLimited
  • 17970 Answers

SOURCE: change a headlight assembly Jeep Grand Cherokee

Just need take off the screws; for details check the graphics and ilustrations in the Jeep ZJ Grand Cherokee Service Manual

Hope helps (remember rated this) Good luck..

Posted on Jan 20, 2010

  • 306 Answers

SOURCE: speakers for 1994 jeep grand cherokee

6.5" in all the doors dash is wierd. 2.75" but i have been able to squeez in a 3.5"

Posted on Feb 04, 2010

Testimonial: "thank you so much, that helps me out as lot"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace Front Wheel Hub Bearing 2002 Jeep Grand Cherokee 2 wheel drive


Removal
  1. Raise and support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the brake caliper, caliper anchor, rotor and ABS wheel speed sensor.
  4. Remove the cotter pin, nut retainer and axle hub nut.
  5. Remove the hub/bearing mounting bolts from the back of the steering knuckle. Remove hub/bearing from the steering knuckle and off the axle shaft.
Installation
  1. Install the hub/bearing to the knuckle.
  2. Install the hub/bearing-to-knuckle bolts and tighten to specification.
  3. Install the hub washer and nut. Tighten the hub nut to specification. Install the nut retainer and a new cotter pin.
  4. Install the brake rotor, caliper anchor, caliper and ABS wheel speed sensor.
  5. Install the wheel and tire assembly.
  6. Remove the support and lower the vehicle.

Apr 22, 2012 | 2002 Jeep Grand Cherokee

2 Answers

How do I remove and install hubs on the front end of a 97 jeep grand cherokee?


It is actually very easy. Lift the vehicle and support it properly remove the 5 lug nuts retaining the wheel. Remove the wheel. If it is a 4 wheel drive remove the spindle nut locking the c.v. axle to the hub. Remove the washer. Push the axle through the splined hub. using a 13 mm or 15mm depending on the hub remove the three bolts reatining the hub assemble to the steering knuckle. assemble in reverse order.

Feb 27, 2011 | 1997 Jeep Grand Cherokee

1 Answer

2006 jeep cherokee suspension problems and cost to fix sounde like and feels like too much play in front and small bumps are too harsh


At around 50,000 miles I had a similar issue and had to replace the right bearing hub assembly. I was having a vibrating issue also, so this may not be the same issue.

Jul 18, 2010 | 2006 Jeep Grand Cherokee

1 Answer

After driving the jeep for 20-30 min the front


it sounds to me like you need tie rods and hub assembly's and bushings

Mar 14, 2010 | 1994 Jeep Grand Cherokee

2 Answers

Why on jeep grad cherokee is o pulse o spark 1994 4.0


Could be Camshaft possition sensor, located in distributor assembly. Easy fix, but costs around $150 due to it is a dealer part only. Hope this helps!

Jun 11, 2009 | 1994 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...