Question about Daewoo Cars & Trucks

Open Question

1999 daewoo nubira 2.0 timing mark position - Daewoo Cars & Trucks

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Benimur
  • 6966 Answers

SOURCE: 1999 daewoo nubira (RPM)

Hi,

Based on your description, could be anything:

  • throttle control (including A/C compensator);
  • auto choke;
  • engine management;
  • auto cruise (if your model has one)
A couple of clarifying questions:
  1. What is your standard set idling RPM, 1000? with or without A/C?
  2. Automatic or conventional/manual trnasmission?
  3. When was the last major tune-up? What parts were replaced?
  4. Does it sound like misfiring also?
  5. Any other indicators, hard starting, long warmup, stalling, excessive gas consumption, smarting to the eyes exhaust fumes?
  6. Does your battery light lits up?
Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Posted on Jul 27, 2008

Ad
Ray190te
  • 61 Answers

SOURCE: timing marks for a daewoo nubira cdx

Here is a pic if the timing marks two small marks on the cam pulleys and one small cut away on the crank pulley .
3d2c66e.png

Posted on Jan 19, 2009

emissionwiz
  • 76649 Answers

SOURCE: cannot figure out timing marks on a 2000 daewoo nubira

Required tools:
13mm open end wrench 10mm shallow and deep socket 8mm socket long flathead screwdriver 17mm deep socket T50 torx socket 1/4", 3/8ths and 1/2" ratchets and extensions E10 inverted torx sockets 6mm Allen wrench 15mm open end wrench 7mm socket 12mm open end wrench 14mm socket 12mm socket 8mm, 9mm and 10mm Allen head sockets 19mm socket pry bar needle nose pliers
If you are doing this because your timing belt broke you will also need to buy a complete cylinder head, head gasket set, and both idler pulleys. ALL DAEWOO MODELS WILL BREAK THE INTAKE AND EXHAUST VALVES WHEN THE TIMING BELT BREAKS.
Start by removing the air cleaner assembly from the throttle body, remove the air filter and housing jack up the vehicle and remove the wheel, remove the plastic shielding in front of the accessory drive belt assembly, remove the accessory drive belt, place a jack with a block of wood on top underneath the engine oil pan remove the front engine mount, remove the crank shaft pulley ( the 4 Allen head bolts only not the 17mm bolt in the center.) remove the metal plate behind the engine mount bracket on the engine, remove the plastic timing belt cover 3 clips on top 2 10mm bolts on bottom. Rotate the engine until the #1 cyl. is at Top Dead Center on the compression stroke or line up the crankshaft timing mark with the mark on the inner timing belt cover ( notch in cover with notch in pulley) on the camshaft pulleys -- ( intake cam line up the line on the pulley with the line on the inner cover)( exhaust cam line up the arrow on the pulley with the arrow on the inner cover) loosen the 13mm bolt in the belt tensioner and using the Allen wrench rotate the tab until there is slack in the belt. Remove the belt. At this time I would recommend you replace the water pump, both plastic idler pulleys as they tend to overheat and lockup, and the belt tensioner. Make sure all your marks are lined up, you may need a helper to hold the Exhaust Cam in place as it tends to move during belt installation. Put the timing belt underneath the crankshaft pulley, install the belt leaving the intake cam for last and NO BELT SLACK on the right side between the crank and the exhaust cam. Once the belt is installed rotate the crankshaft over 2 revolutions and make sure is rotates freely, and your timing marks are aligned perfectly if not the engine will not run properly, tension the belt as needed. Installation is the same as removal.

To clarify, on the DOHC engine, the intake cam gear has a line on it, and the exhaust cam gear has an arrow on it. These should be lined up with the corresponding line and arrow on the VALVE COVER, pointing straight up. I just went through this process over the weekend, and spent quite a bit of time looking for these marking as I had removed the valve cover. Once I found them, it was plain and simple.
In addition, be sure to not over tighten the belt when reinstalling. The tensioner has markings on it for "old" and "new". DO NOT adjust past "new", as the car will sound like a jet engine, and the belt will not last for very long.
One more item that you may as well replace while you are in there is the cam position sensor if you have not already, as there have been issues with them, and the timing housing has to be opened to get to it

Posted on Mar 04, 2009

alicantecoli
  • 22219 Answers

SOURCE: 2000 Daewoo Nubira camshaft position sensor

on the front under timing belt cover ,back cam ,if its not their then back of head about 3inches along from the gear wheel end

Posted on Sep 11, 2009

stevenhurc
  • 450 Answers

SOURCE: timing mark diagram

here are the timming marks

7a3496b.jpg
e98992a.jpg
the other important thing is to
Rotate the automatic tensioner hex–key tab anti-clockwise until the adjust arm pointer of the timing belt automatic tensioner is aligned with the notch in the timing belt automatic tensioner bracket.
then turn engine over 2 turns and recheck marks and tensioner pointer

Posted on Nov 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I get a diagram for timing for a daewoo


There is 2 possibilities. if it has the marks on the valve cover as in the first picture then use those to align the cam gear timing marks to. If no marks on the valve cover then point the cam gear timing marks at each other as per the pictures then align the crankshaft timing marks as pictured.

25112305-go2qkqusq2vchyq30ywu0a0h-5-0.jpg

25112305-go2qkqusq2vchyq30ywu0a0h-5-1.jpg

25112305-go2qkqusq2vchyq30ywu0a0h-5-3.jpg

Sep 18, 2014 | 2000 Daewoo Nubira

1 Answer

What. Is. The. Position of. No 1piston. When. Setting. The. Timing. On. Daewoo. Nubira. Cdx. 2 l


after you remove the timing belt covers on the crankshaft gear have a noch face down to alaing tho the oil pump cover on the camshafts have two marks a the top of timing cover

Sep 09, 2014 | 2002 Daewoo Nubira

1 Answer

Daewoo nubira 2002


Please follow this link to the see the whole process with diagrams of the belt change. Please note if the belt broke you likely have bent valves.

Oct 17, 2012 | 1999 Daewoo Nubira

2 Answers

Looking for cambelt timing marks/ positions please, Twin cam engine Thanks Kevin


these bend valves if belt breaks while running
Align the timing marks on the camshaft gears to the notches on the camshaft cover, using the intake gear mark for the intake gear and the exhaust gear mark for the exhaust gear.
Align the mark on the crankshaft gear with the
notch at the bottom of the rear timing belt cover.

May 12, 2009 | 1999 Daewoo Nubira

1 Answer

Jumped time need to know timing mark


Sorry for the delay.
I am personally going back to answer your unanswered question. I do not know if you still need the answer, but I am going to answer it in case you still do.

Click on the following direct Link. It has the Timing Belt/MARK(S) Diagrams that you will need, complete with Instructional and Directional Diagrams.

Again my apologies...
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1999/make/daewoo/model/nubira/1999_daewoo_nubira_timing_belt_diagram_marks.htm

Apr 23, 2009 | 1999 Daewoo Nubira

1 Answer

Daewoo nubira timing marks


no timing marks on cover, timing marks are on sprokets they should be lined oposite each other.

Jan 17, 2009 | 1999 Daewoo Nubira

1 Answer

Timing marks for a daewoo nubira cdx


Here is a pic if the timing marks two small marks on the cam pulleys and one small cut away on the crank pulley .
3d2c66e.png

Dec 14, 2008 | 1999 Daewoo Nubira

2 Answers

Need a picture diagram of 1999 daewoo Leganza timing belt setting or mars?


need a picture diagram for timing marks nubira 2001 2.0L

Jul 20, 2008 | 2002 Daewoo Nubira

1 Answer

I have replaced broken timing belt on 1999 daewoo nubira and all timing marks line up but it will not idle properly and knocks


did the timing belt snapbefore you replaced it? if so you may have bent some valves. if not recheck timing marks and distributor position.

Jul 06, 2008 | 1999 Daewoo Nubira

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...