Question about Toyota Hilux

Open Question

Central locking relay/module for 2011 hilux 2,5 d4d s/c

I am attempting to lacate either the module or the relay or module that sends power to the drivers door.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

tommyboinow
  • 324 Answers

SOURCE: Audi A4 Y Reg 2001, Central locking

reset you computer, do this by removing the positive battery cable for 10 mins.

Posted on Nov 26, 2008

  • 4369 Answers

SOURCE: 2000 Ford Focus automatic door locks quit working.

check fuse 63 first.

Visual Inspection Chart Mechanical Electrical

  • Binding latch mechanisms
  • Binding linkage
  • Misaligned door
  • Central junction box fuse 63 (20A)
  • Damaged wiring harness
  • Loose or corroded connection(s)
  • Circuit
  • Door lock switch
  • Door lock actuator



It could also be your GEM (generic electronic module) which is expensive as it controls a lot of stuff. A scan tool can be used to cehck for fault codes from the GEM.

Posted on Jun 23, 2009

  • 3 Answers

SOURCE: 1999 Audi A3 1.8T Electric Windows and Central Locking Won't work

will your passenger door open with the key and is it just one side that your windows are not working or both. if its just one side it might be your regulator motor in the door thats not working if its both it might be your central locking pump usually in the boot. however if both of them are working fine it could be that your key needs reprogrammed however i think the 1st 2 are more likely to be the problem.

Posted on Jun 30, 2009

ghost45
  • 1280 Answers

SOURCE: 2004 Hyundai Sonata door lock functions inoperable.

you have a bad relay.. the 'lock' relay.

Posted on Sep 23, 2009

  • 149 Answers

SOURCE: land rover discovery central locking.

No, likely to be caused by the actuators in the lock mechanism failing usually causing the door to remain locked. The boor door can also fail this way, as do the front side doors. Replacement requires the whole lock unit to be replaced at a cost of roughly £60 a lock, and a hours work. Helps if you have small hands. Requires a full strip down of the door and you will need the lock unit, trim clips (a few quid) and a trim removal tool (tenner). You can bodge with a flat head screwdriver, but the tool does help prevent damage to the clips & trim panel.

Posted on Feb 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 GMC Envoy: I tested all of the fuses and all of them check out but my power locks, cabin lighting, dash panel lights, etc. aren't working.


Which fuse box ? Do you know what a DDM -is ? Driver door module . Do you have any idea what all is involved in making these thing's you have listed work ? A lot more then a fuse , there could be DTC'S - diagnostic trouble codes stored in the principal Control module ,the BCM , That could save a tech. valubale time in diagnoising this problem !
Door Lock System Components
The power door lock system consists of the following components:
• Driver Door Module (DDM)
• Passenger Door Module (PDM)
• Liftgate Module (LGM)
• Door lock relay
• Door unlock relay
• Body Control Module (BCM)
• Reversible door lock actuators in each of the doors
• LR/RR LOCKS 10A fuse (relay supply voltage)
• Door lock switches in driver and passenger doors (switches are integral components to the DDM and PDM)
Did you know there is a fuse box in the rear of the vehicle ?
Fuse Block - Rear
Beneath the left rear seat
The inside lights are also controlled by the BCM , and the fuse's are also located in the rear fuse box .
The body control module (BCM) directly sends a 5-volt reference voltage to the instrument panel (I/P) dimmer switch which is then adjusted based on the I/P dimmer switch position and returned as a low reference and a signal to the BCM. The BCM uses this signal to directly control the desired level of instrument panel illumination lamp intensity.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC B2620 Display Dimming Pulse Width Modulation (PWM) Input Circuit. There are several DTC'S that can set !
DTC B3801 Passenger Compartment Lamp Request Circuit
DTC B2610 Passenger Compartment Dimming 1 Circuit plus others for power locks .
Thank You Uncle Sam

Nov 29, 2016 | 2006 GMC Envoy

1 Answer

Where is the power window relay located in 2004 bonneville pontiac? thanks


Are all the windows inoperative ? The power window system on this vehicle is very complex in nature . Door modules , serial data communication networks ,messaging commands between modules etc... Factory description
Power Windows Operation
The vehicle is equipped with power windows controlled by the door modules. Each passenger door window can be operated, either from a switch built into the driver door switch assembly (DDSA), or from a switch mounted locally to its associated door. The driver door window can be operated only from the driver door window switch built into the DDSA.
When a window is operated from the DDSA, the DDSA interprets the window switch signal as a specific window switch request and sends the information to the driver door module (DDM) via the power door serial data circuit. The DDM examines the request and checks to see if it has received any class 2 serial data messages from any of the other vehicle modules (i.e. ignition switch position) prohibiting the movement of the window. If the window being operated is the driver door window, and if no prohibitive class 2 messages have been received, the DDM then applies voltage and ground to the driver door window motor to move the window glass as requested. If the window being operated is a passenger door window, and no prohibitive class 2 messages have been received, the DDM sends the request, via the power door serial data circuit, to the appropriate passenger door module. The passenger door module then applies voltage and ground to the passenger door window motor to move the window glass as requested.
When a passenger door window is operated from the power window switch mounted locally to its associated door, the passenger door module first checks to see if the DDM has received any prohibitive class 2 serial data messages. If there are no prohibitive messages, the passenger door module powers the associated passenger door window motor.
Both front door windows have the express down feature. This allows the front door windows to be fully opened by momentarily pulling the appropriate window switch lever to the second detente and then releasing.
I have heard of water on rear floor shorting the data bus bring down the system . no power window operation . There are bus wires under the carpet an a scotch lock connector that corrodes causing this problem . This may or may not be your problem but you can stop looking for relays because their are none involved in the control of the power windows on your vehicle .
I

Jun 23, 2016 | Cars & Trucks

1 Answer

Why does my 2004 Chevy Silverado lock and unlock while in drive? When turned off and no keys in ignition the drivers door will unlock on its own a short time later.


Gremlins ! HA HA HA sorry ! First off a little bit on how they work an what all is involved in making them work ! There are a few control modules in the mix , switches ,relays etc...
Door Lock System Components
The power door lock system consists of the following components:
?€¢
The driver door module (DDM)

?€¢
The passenger door module (PDM)

?€¢
The body control module (BCM)

?€¢
The driver information center (DIC)

?€¢
The rear door lock switch

?€¢
The door lock relay

?€¢
The door unlock relay

?€¢
The liftgate lock relay--utility vehicles with liftgate only

?€¢
The reversible door lock actuators in each of the doors and liftgate

?€¢
LOCKS 20A fuse (rear lock/unlock relay supply voltage)

?€¢
ECC 10A fuse (liftgate lock relay supply voltage)

Door Lock System Controls
The power door lock system can be controlled by any of the following:
?€¢
A power door lock or unlock switch activation

?€¢
A keyless entry transmission

?€¢
An automatic door lock function

?€¢
A delay lock function

?€¢
Door lock cylinder switch activation

?€¢
Lockout Prevention

?€¢
An airbag deployment

The front power door lock switches are integral components of the driver door module (DDM) and passenger door module (PDM). The switches are two position normally open rocker switches. When placed in either the lock or unlock positions, the switches provide a direct input to the DDM or PDM. The DDM or PDM monitors these inputs and sends a Class 2 message indicating a change in the switch's respective position. Modules which activate the power door lock motors receive the Class 2 message and activate the motor in the appropriate direction to lock or unlock the vehicle's doors and liftgate. The rear door lock switch provides a lock and unlock signal to the body control module (BCM). The BCM upon receipt of a lock or unlock signal will control the rear door lock relays and also send a Class 2 message to the DDM and PDM to perform the appropriate function.
The modules which activate the power lock motors are:
?€¢
The DDM (driver door lock actuator).

?€¢
The PDM (passenger front door lock actuator).

?€¢
The BCM (both rear door lock actuators and cargo door/liftgate).
The DDM and PDM are directly connected to the respective door lock actuator through the door lock motor lock and unlock circuits. Once a door lock or unlock request has been received, the module will supply battery voltage to one side of the actuator and ground the other causing the doors to lock or unlock.
The rear passenger and cargo doors differ slightly in that they use lock and unlock relays. The relays supply and coil sides receive a constant voltage through the battery voltage supply circuit. The normally closed contacts are connected to ground and the control side is connected to the BCM. Once a door lock or unlock request has been received by the BCM, the BCM will ground the control side of the appropriate relay. This energizes the relay and allows voltage to be applied to either the door lock motor lock or unlock circuits. since the other side of the door lock actuator is connected to the normally closed contacts of the opposing relay to ground, the doors lock or unlock.
The first place to start is have a factory or equivalent scan tool hooked up , one that can read BCM DTC'S - diagnostic trouble codes ! This could lead to a fix faster ! Watch these three videos !
Door Locks Go Crazy 1

Sep 16, 2015 | Cars & Trucks

1 Answer

Where the window relay is located in a 2003 jeep grand cherokee?


relay, way assume there is one?
did you SCAN it yet ? got PCI comm errors. or door module errors?
why not post symptoms and ask for help.
that works not guessing... in 99% of all cases.

WJ jeep covers all this in the FSM book, or at alldata.com
ending the guessing game. fast.
chapter 8 is wiring in the jeep book.
next is power window . 8N- page 33 is there. theory of ops.

are all windows dead, or just one, must I ask>?
FSM chapter 8w-60 -2 shows,
NO RELAY.

it has 2 modules
the driver module DDM and passenger module, fuses and motors.
now the bad news.
the BCM brain, sees what buttons you press, then the BCM
sends a digital message stream to the MODULES
the modules then do as they are told. via the PCI network.

(that is how it all works with min words)
so what does the shop do.
well he scans first. (after checking all fuse)
PDC fuse 12 , 50 amps. (first if all windows are dead)

now on page 4 they show RHD and export models with no brain
that is , just door switches that go to motor direct, and again
not one relay, in this system..
BCM top left
PCI bus below it.
driver door module getting commands. (serial)
look ma' no switches or relays. (usa cars)

24778773-ylqjikjamog5a0is5ho2uz3h-1-0.jpg what is inside the module is a jeep secret.

the BCM does the magic where by you command driver window down and it does so automatically. this is software doing that in the BCM. a big clue if your jeep has this BCM system. show above.

ill now quote the FSM book
The most reliable, efficient, and accurate means to
diagnose the power window system requires the use
of a DRB scan tool and the proper Diagnostic Procedures
manual. The DRB scan tool can provide confirmation
that the PCI data bus is functional, that all
of the electronic modules are sending and receiving
the proper messages on the PCI data bus
, and that
the power window motors are being sent the proper
hard wired outputs by the door modules for them to
perform their power window system functions.


if you dont have this option DDM ?
then the fuse is blown
or the switches are bad, super easy to diagnose, ask. how.

Jul 07, 2014 | 2003 Jeep Grand Cherokee

1 Answer

2005 Chevrolet Tahoe Power Windows and Power Locks not working.


The power windows an power locks are controlled by a module , DDM - driver door module . As far as the locks locking when you put the vehicle into reverse an unlocking when you put the vehicle into park , that's how there are suppose to work , automatic lock an unlock feature . When you put the vehicle into any gear from park the locks should lock . Did she hit window lockout function ?

The power door lock system consists of the following components:
• The driver door module (DDM)
• The passenger door module (PDM)
• The body control module (BCM)
• The driver information center (DIC)
• The rear door lock switch
• The door lock relay
• The door unlock relay
• The liftgate lock relay--utility vehicles with liftgate only
• The reversible door lock actuators in each of the doors and liftgate
• LOCKS 20A fuse (rear lock/unlock relay supply voltage)
• ECC 10A fuse (liftgate lock relay supply voltage .

Programmable Automatic Door Locks
The automatic door lock feature can be programmed to control the door lock system. The automatic door lock feature is factory programmed to have all doors lock and unlock. For detailed instructions on programming the automatic door locks, refer to Vehicle Personalization in Personalization.
When the automatic door lock feature is programmed to control the door lock system, the driver door module (DDM), passenger door module (PDM) and body control module (BCM) will lock the vehicle doors if the following inputs are true:
• Ignition 1 input is active.
• All door jamb switch inputs are inactive.
• Cargo door or liftgate/liftglass ajar inputs are inactive.
• Transmission is shifted out of park.
This automatic door lock function will only occur once per ignition cycle unless, a door jamb switch input changes state to active and back to inactive. Then the DDM, PDM and BCM will lock all doors again.
Once the automatic door lock feature has locked the doors, the BCM will then unlock all the doors when the transmission is shifted into park.
Driver, Passenger and Cargo Door Lock System Operation
The front power door lock switches are integral components of the driver door module (DDM) and passenger door module (PDM). The switches are two position normally open rocker switches. When placed in either the lock or unlock positions, the switches provide a direct input to the DDM or PDM. The DDM or PDM monitors these inputs and sends a Class 2 message indicating a change in the switch's respective position. Modules which activate the power door lock motors receive the Class 2 message and activate the motor in the appropriate direction to lock or unlock the vehicle's doors and liftgate. The rear door lock switch provides a lock and unlock signal to the body control module (BCM). The BCM upon receipt of a lock or unlock signal will control the rear door lock relays and also send a Class 2 message to the DDM and PDM to perform the appropriate function.
The modules which activate the power lock motors are:
• The DDM (driver door lock actuator).
• The PDM (passenger front door lock actuator).
• The BCM (both rear door lock actuators and cargo door/liftgate).
The DDM and PDM are directly connected to the respective door lock actuator through the door lock motor lock and unlock circuits. Once a door lock or unlock request has been received, the module will supply battery voltage to one side of the actuator and ground the other causing the doors to lock or unlock.
The rear passenger and cargo doors differ slightly in that they use lock and unlock relays. The relays supply and coil sides receive a constant voltage through the battery voltage supply circuit. The normally closed contacts are connected to ground and the control side is connected to the BCM. Once a door lock or unlock request has been received by the BCM, the BCM will ground the control side of the appropriate relay. This energizes the relay and allows voltage to be applied to either the door lock motor lock or unlock circuits. since the other side of the door lock actuator is connected to the normally closed contacts of the opposing relay to ground, the doors lock or unlock.

Mar 16, 2017 | 2005 Chevrolet Tahoe

1 Answer

I have power to the door lock switches on the drivers door but the locks do not work nor does the back hatch or the switch at the back hatch that controls all the locks in the vehicle. Do the locks g


Power Door Locks Circuit Description
The power door lock system incorporates door lock switches on both front doors and on the RH D-pillar, door lock motors in all passenger doors and in the RR cargo door, a door lock relay and a door lock control module.
Power for the door lock switches and the door lock control module is supplied from the CIG LTR fuse 13 through CKT 640 (ORN). Power for the door lock relay is supplied from the PWR ACCY circuit breaker through CKT 540 (ORN). Ground for the door lock relay is supplied from G202 through CKT 150 (BLK) and ground for the door lock control module is supplied from G400 through CKT 150 (BLK).
The door lock motors are reversible and both sides are connected to the normally closed contacts of the door lock relay. Those contacts of the relay are connected to G202. When any of the door lock switches are placed in the lock position, voltage is supplied through CKT 195 (LT BLU) to the relay lock coil. Since the other side of the lock coil is connected to ground, the coil is energized and it pulls the lock contacts closed. Voltage is then supplied through CKT 295 (GRY) to all the door lock motors and the doors lock. The unlock function operates in much the same manner except that when any of the switches are placed in the unlock position, voltage is supplied through CKT 194 (WHT) to the unlock coil of the relay and CKT 294 (TAN) supplies voltage to the apposite side of the door lock motor and the doors unlock.
Door Lock Control Module Description
The door lock control module is used on vehicles equipped with cargo doors. The purpose of the module is to lock the cargo doors after a lock cycle has been commanded from any of the door lock switches with the cargo doors open. When the RH cargo door is open, the module receives a ground signal from the closed contacts of the rear door jamb switch on CKT 1897 (ORN/BLK) to G400. When a lock command is received, the module retains this input until it receives an open input from the rear door jamb switch. Then the module sends a lock command through CKT 194 (WHT) to the door lock relay and the doors lock.
Rear Cargo Doors Description
The power door lock motor will not operate unless the rear cargo doors are fully closed. The power door lock motor is in the right cargo door. The contactors are on the rear cargo door opening on the body and on the right cargo door.

May 23, 2017 | 1997 GMC Yukon

1 Answer

We have a 2001 Ford Escape with a small problem. The remote key fob locks the doors and unlocks the doors but the lights don't flash anymore when you lock the door. The horn also won't honk after hitting...


I think you need to reprogram the module, you deleted the horn chirp and light flash confirmation. he dealer can reprogram for you.


Customer Preference Items NOTE: If using the WDS, select Module Configuration and Programming, then follow the screen prompts.
NOTE: Make sure module is listed as supporting customer preference items and supports the specific item to be configured in the Module Configuration Index in this section.
  1. Select Service Bay Functions on the diagnostic tool.
  1. Select the module that contains the customer preference item to be programmed. Refer to the Module Configuration Index in this section.
  1. Select Customer Preference Items on the diagnostic tool.
  1. Select Module Option Content.
  1. Select the item to be enabled or disabled.
  1. Enable or disable the item as necessary to reflect the customer preference.
------------------------------------------------------------------------

----------------------------------------------------------------------------
Principles of Operation
Power Door Locks
The generic electronic module (GEM) controls the power door lock and keyless entry system. Lock and unlock operation is achieved through the use of internal relays in the GEM. The relays are all door lock, all door unlock and driver door unlock. The normal path of the relays is to ground.
Pressing the door lock control switch to lock or unlock sends a ground signal to the GEM. The same GEM pin is used for unlock and lock input. The unlock signal is a direct connection to ground. The lock signal is altered by an internal resistor in the door lock control switch. This varied resistance identifies lock or unlock command to the GEM.
The door locks can also be controlled by the door key cylinder switches. For the liftgate door lock switch, turning the key to lock or unlock sends a ground signal to the GEM. The GEM will then ground the all door lock or all door unlock relay supplying voltage to the actuators. Turning the driver door key cylinder to the lock position sends a ground signal to the GEM. The GEM will then ground the all door lock relay supplying voltage to the actuators. Turning the driver door key cylinder to unlock sends a ground signal to GEM. The GEM will ground the driver door unlock relay and supply voltage to only the driver door actuator. If a second unlock ground is received within three seconds of the first, the GEM will ground the all door unlock relay supplying voltage to the passenger door actuators (if 2-stage unlock is equipped).
Keyless Entry
The keyless entry remote transmitter sends a signal that is received by the GEM internal antenna. Depending on the signal received, the GEM module will ground the appropriate internal relay and lock all doors or unlock the driver door. If the unlock signal is received again within three seconds of the first unlock, the GEM will ground the internal all door unlock relay unlocking all doors. The lock and unlock relay output to the actuators is controlled by the GEM, the same as power door lock operation from the control switch.
If the signal received is for the panic button, the GEM will cycle ground to the park lamp relay coil and horn relay coil. The park lamps and horn will continue to cycle until the panic button is pressed again or the ignition switch is turned to the RUN position, or after the timer expires.

Dec 17, 2009 | 2005 Ford Escape

1 Answer

Camry 1996 automatic power lock doen't work, but windows work.


if you can here relays when unlocking/locking check for power at door lock actuators inside doors, if you have power on lock/unlock and good earth from connector actuators are faulty.
if no power on test light when operating check output from central door lock module while operating, none coming out of module then it might need replacing.
check 30Amp power fuse for main relay under bonnet (which goes to pin 8 white/blue on module)and 10Amp gauge fuse in cab(pin 1 blue/red on module),pin 15 is also power when relay is on(red/blue) with test light, and module/ actuators.
check outputs from module pin 3 & 4
blue/red
blue/black
that go to door locks

Jul 20, 2009 | 1996 Toyota Camry

1 Answer

Rear side windows


This may be just a case of inadvertently hitting the window lock out n th driver door window switch by mistake. Check that first. Here's some background on window operation

Principles of Operation
The driver power window regulator motor is controlled directly by the master window/door lock/unlock switch (and its integrated "auto down" module). Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The driver power window regulator motor is a reversible motor that is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The passenger power window regulator motor is controlled directly by the passenger power window switch and can also be controlled by the master window/door lock/unlock switch. Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The passenger power window regulator motor is a reversible motor, which is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The power rear quarter glass is also directly controlled by the master window/door lock/unlock switch. The power rear quarter glass power latches also utilize reversible motors. The power rear quarter glass power latches are operated by applying power and ground to the motor leads to open the window, and then reversing polarity on those same leads to close the window.
Symptom Chart Condition Possible Sources Action
  • All windows are inoperative
  • BJB Fuse:
    • F20.
  • Circuit.
  • Power window relay.
  • Front door power window switch.
  • GO to Pinpoint Test A .
  • Single power window is inoperative
  • Front door power window switch.
  • Front door power window regulator.
  • Circuit.
  • Driver door power window switch.
  • GO to Pinpoint Test B .
  • Vent power window is inoperative — quarter window glass power latch
  • Circuit.
  • Quarter window glass switch.
  • Quarter window glass power latch.
  • GO to Pinpoint Test C .
  • The one touch down feature is inoperative
  • Master window regulator and door lock switch.
  • INSTALL a new master window/door lock/unlock switch. REFER to Switch—Master Window Door Lock/Unlock .
  • The back window will not defrost
  • CJB Fuses:
    • F30 (10A).
    • F32 (20A).
    • F34 (20A).
  • BJB Fuse:
    • F27 (45A)
  • Circuit.
  • Heated back window switch.
  • SEC/timer module.
  • Rear window defrost relay.
  • GO to Pinpoint Test D .
  • The back window defrost will not shut off automatically
  • SEC/timer module.
  • Circuit.
  • Rear window defrost relay.
  • GO to Pinpoint Test E .

Jan 28, 2009 | 1999 Mercury Villager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...