Question about Cars & Trucks

1 Answer

2004 Sebring limited conv. Fob sounds like doors unlock but dont

When I press the lock or unlock button on my keyless fob, the doors make the clicking sound but dont lock or unlock.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 22,095 Answers

Sorry would need to see it to have any idea ,could be the internal mechanism on both sides has broke at the same time to a low voltage to the locking solonoids ,maybe even a bad ground or earth connection .would need to wave my magic hammer at it to know for sure

Posted on Apr 09, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: i have a grand voyager

dont go through all the hassles of removing the door trim just take the terminal off the battery for about a minute then reconect again worked on mine good luck

Posted on Dec 20, 2008

tbirdfan1
  • 3051 Answers

SOURCE: key fob will not lock or unlock doors on 06 Sonata

Hi there
i have the same problem but mine is the sensor that is under the dash that is faulty so i had them disable it untill i can get a part that they need to order so i would have your dealer check the sensor .. if it is under warranty they will replace it for free

Posted on Mar 08, 2009

  • 412 Answers

SOURCE: 2005 Chrysler Grand Voyager. Central locking

the body control module may need a software update..check with your local dealer

Posted on Jun 12, 2009

  • 4793 Answers

SOURCE: my Porsche Cayenne S Key fob no longer unlocks the Door

unlock the door then press the lock button on remote and hold down for 20/30 secs.manual does say hold button.....

Posted on Mar 02, 2010

  • 52 Answers

SOURCE: my Porsche Key fob no longer unlocks the doors

Insert key into door barrel or ignition lock and turn key, whilst doing this press the unlock/lock button, the led on the dash should flash to indicate this has initialised the key to the car, then remove key and test operation of remote. If this fails then a new remote plus coding to the car by your dealership is needed

Posted on Apr 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 jeep grand cherokee limited 4.0, the keyless control just unlock all the doors with the front passenger door open


be more clear., please.
what works, and dont, using all ways to lock a car.
all doors. all methods.
inside or out side car. (fob and not fob ways)
only that matters

Nov 14, 2016 | 1999 Jeep Grand Cherokee Limited

1 Answer

Keyless remote will not respond to my 2004 ford expedition


try replacing the battery in it first. If that doesn't work and you have another key fob that is working correctly, cycle the key from off to key on engine off 8 times till you hear the doors lock and unlock. Then press a button on the key fob that works and then the one that does and cycle the key off and it should be re-programmed. If this doesn't work you may need to replace the key fob.

Apr 12, 2014 | 2004 Ford Expedition

1 Answer

Doors dont lock with secrity fob


The receiver for the fobs is located in the rear hatch, and it needs to be reprogrammed to the fobs. Try the following procedure;

1. Close all the vehicle doors.
2. Insert the ignition key into the ignition lock cylinder.
3. Press and hold the door unlock switch.
4. While holding the door lock switch in the unlock position, cycle
the ignition ON, OFF, ON, OFF.
5. Release the door unlock switch. The doors will lock and unlock to
confirm the program mode.
6. Press and hold the LOCK button and the UNLOCK button
simultaneously on one transmitter. After a delay of approximately 15
seconds, the doors will lock and unlock to confirm the programming of
that transmitter.
7. Repeat the previous step to program up to four transmitters.
8. Turn the ignition switch to the RUN position in order to exit the
keyless entry transmitter mode.
9. Operate the transmitter functions in order to verify correct
system operation.

Sep 05, 2012 | 2004 Chevrolet TrailBlazer

1 Answer

When i lock al my doors on my 2004 Chrysler pacifica from my keychain all doors lock except for the driver door. The alarm is still activated but if someone tries to open the driver door it will open and...


This can happen If you have used the IGN. key to unlock the drivers door after you locked them from the fob. This can also be caused by a stuck button on the drovers door. Check the drivers door all buttons to see if any are stuck. If you do not have any stuck buttons. Try this, from inside the car, with out the car running, use the button on the drivers door to "lock all doors". Then use the fob to unlock them, then get out and press the lock button on the fob twice real quick. This should cause the drivers door to lock as the others. Hope this helps Fix Ya Up.

Jul 03, 2011 | 2004 Chrysler Pacifica

1 Answer

1996 tl keyless entry


Do you have a keyless entry FOB. If you do replace the battery then program the system. Unlock the doors turn the ignition key to the "ON" position then press either the lock or unlock button of the FOB turn the ignition key off.Now turn the ignition key on again and press either button on the FOB. Turn the ignition off again. Do this 3 times. This initiates programming for the power door locks. Press the lock button of each remote one at a time to be stored in memory. this must be done within 10 seconds of each remote.
3 remotes max. Turn the ignition off and remove the key to complete programming procedure. then test each remote.

Apr 05, 2010 | 1996 Acura TL Series

1 Answer

RS Focus registered yesterday 19th March Keyless entry but remote fobs do not lock or unlock car. The car was driven back yesterday hav ing now covered 114 miles alarm was going off last night but thats...


should not be using fob buttons for entry or locking for emergency only .if keyless entry walk up to car with fob do not press any buttons see if door opens then walk away from car with fob about 20m then go back to car without fob and see if door locked if so all working fine .indicators will not flash if the above dont work take back to main dealer for diagnostics keys may need to be reprogrammed

Mar 20, 2010 | 2009 Ford Focus

1 Answer

How do i program a key fob for a 2004 buick lesabre


ok try this, turn the ign on but dont start the vehicle, press and hold the unlock door lock button, the door locks will lock and unlock twice, then let go press and hold the lock botton on your key fob, the door locks should lock and unlock, turn the ign. off and on off again, that should do it.

Oct 11, 2009 | 2004 Buick LeSabre

2 Answers

How do u program a new key fob for a 2004 chevy Malibu


Close all the vehicle doors.
Insert the ignition key into the ignition lock cylinder.
Press and hold the DOOR unlock switch.
While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode.
Press and hold the LOCK button and the UNLOCK button simultaneously on one keyless remote. After a delay of approximately 15 seconds , the doors will lock and unlock to confirm the programming of that transmitter.
Repeat the previous step to program up to four transmitters.
Turn the ignition switch to the RUN (one more click forward) position in order to exit the keyless entry transmitter mode.
Operate the transmitter functions in order to verify correct system operation

Jun 04, 2009 | 2004 Chevrolet Malibu

2 Answers

Program fob


Instructions to program a keyless entry remote for a Chevy Silverado. They also work on 2003, 2004 and 2006 Suburbans.
  1. Close all the vehicle doors.
  2. Insert the ignition key into the ignition lock cylinder.
  3. Press and hold the DOOR unlock switch.
  4. While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
  5. Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode.
  6. Press and hold the LOCK button and the UNLOCK button simultaneously on one keyless remote. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
  7. Repeat the previous step to program up to four transmitters.
  8. Turn the ignition switch to the RUN (one more click forward) position in order to exit the keyless entry transmitter mode.
  9. Operate the transmitter functions in order to verify correct system operation

Apr 19, 2009 | 1999 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...