Question about 2005 Ford Ranger

1 Answer

Had rebuilt transmisson put in now put shifter in reverse instantly turns the radio volumn off the radio digital info stays on. any connection to the new transmission. didnt happen before repair

Read it could be nuetral saftey switch

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 44,448 Answers

Check around the bell housing for a wire that is pinched during the re-fittment. There really is no connection between the problem and the replaced transmission so you will have to consider anything electrical not in the correct position

Posted on Apr 08, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1987 Mazda B2000 pick up. My shifter will not fit back on my newly re-built transmission. Do any other shifters work with this model as I am unable to locate an original for replacement.


I'm sure you have checked the shifter and shifter spring,,...Shifters can be rebuilt also....Make sure your clutch linkage is properly adjusted...The clutch is non adjustable...They may have got air in the hydraulic lines while removing and installing...This would give you a spongy pedal ...Most shifters in order to put it in reverse you push over and up or over and down......if shifter is loose and wobbly it won't have enough force to push the reverse shift rod....However if shifter is in great shape it sounds like the reverse shift rod could be hanging up and not sliding the shift fork...It could be the rebuilders fault......Reverse gear is the largest gear in the transmission and it is located at the back of TRANS which means it will require more force to put in reverse.......I would take it back to rebuilders shop and tell them something isn't right with going to reverse gear...if you wait too long they will think it is something you may have done by incorrect shifting.....

Feb 06, 2015 | 1987 Mazda B-Series

1 Answer

My rebuilt transmission won't go forward?


i would be checking the shifter cable adjustment first see how that goes goodluck

Sep 18, 2017 | 1992 Ford F250

1 Answer

My 2002 Jeep Liberty reverse lights are not working,I put in new fuses and bulbs, what could be the problem?


Remove console shifter housing check connectors for good clean connection...If all are clean and connected apply emergency brake start vehicle and put in reverse...with voltmeter or a good test light check wiring at reverse light switch for power and or voltage...normally they will wear loose from normal shifting but if no power replace switch....If it seems like too much work involved you have to take to dealer where they will scan it and find it instantly....it could just be a bad ground at connection.

Feb 24, 2011 | 2002 Jeep Liberty

2 Answers

My 1994 nissan maxima has no problems.but all of a sudden i parked it and when i tried to put it in gear,it wont move.it stays in park.and it wont move


Check your linkage under the car on drivers side. Right next to Transmisson the linkage that goes to your shifter should connect to the linkage coming out of the transmisson. If not, you have a broken linkage.

Feb 23, 2011 | 1994 Nissan Maxima

1 Answer

87 Raider, Tansmission only goes in 1st and reverse.


Take it too a quality good name transmission repair shop. Amco is nationwide

Jul 02, 2010 | 1987 Dodge Raider

2 Answers

Car radio shuts off when out in reverse. Just had tranny rebuilt. Need help


may be the reverse gear is connected to the supposed to be car tv to show the behind of the car when reversing but there is technical problem

Nov 11, 2009 | 1991 Toyota Camry

1 Answer

1984 CJ7 stuck in reverse. Staight 6, 5 speed and will not shift out of reverse.


you have a bent shift fork or shaft, you will need to remove the dust boot pull the shift snap ring it the shifter is in the floor and pull the shifter stick off then remove the transmisson top cover and replace the reverse first shift fork, this is the most common cause, if it has a columm shifter then disconnet the shifter lever and try shifting if it shifts then you have bent linkage and will need to figure out where it is located.

Jul 15, 2009 | 1984 Jeep CJ7

2 Answers

Manual Transmisson Shifter


there is a bushing that keeps the shifter tight it shhould be under the car right under the shifter linkage before the linkage connects

Dec 07, 2008 | 1999 Kia Sephia

2 Answers

My car will not go in reverse but will go forward


typical FWD GM transmission issue, the transmisson will have to be rebuilt. You could try a fluid flush and filter change but there are only 2 discs pack for reverse. Which makes them fail very easily

Jul 06, 2008 | 1996 Chevrolet Monte Carlo

Not finding what you are looking for?
2005 Ford Ranger Logo

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...