Question about 2005 Ford Mustang GT

1 Answer

05 mustang gt codes po 2104 and 2112 replace tcm and tps

Posted by on

  • JOHN PETERMAN
    JOHN PETERMAN Apr 09, 2015

    all happened after battery disconnect

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 11,015 Answers

P2104 - Throttle Actuator Control (TAC) System - Forced Idle Description: The TAC system is in the failure mode effects management (FMEM) mode of forced idle. Possible Causes:

  • Open or short in multiple accelerator pedal position (APP) sensor circuits.
  • Damaged APP sensor.
  • Damaged powertrain control module (PCM).
Diagnostic Aids: This DTC is an informational DTC and can be set in combination with a number of other DTCs which are causing the FMEM. Diagnose other DTCs first. Application Key On Engine Off Key On Engine Running Continuous Memory All

P2112 - Throttle Actuator Control (TAC) System - Stuck Closed. Description: This powertrain control module (PCM) fault status indicates the throttle plate is at a lower angle than commanded. Possible Causes:
  • Binding throttle body, stuck closed.
  • Damaged PCM.
Diagnostic Aids: Application Key On Engine Off Key On Engine Running Continuous Memory All GO to DV1 Are you familiar with electronic throttle control ? You have a dc electric motor on the throttle body an at the gas pedal there are APP pedal position sensors that send voltage signals to the PCM which in turn controls the electric motor opening an closing the throttle ! By what this P02112 states the throttle plate is binding , which means it could be bad or just needs to be cleaned ! You will need to disconnect the electrical connector an see if it is binding by pushing it with finger or thumb . which is ever easiest !
GO to QE1

Posted on Apr 08, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

4.6 Engine valve train in 2008 Ford Mustang Gt


    mages for 4.6 Engine valve train in 2008 Ford Mustang Gt


    More images for 4.6 Engine valve train in 2008 Ford Mustang Gt

    2005-2009 Mustang Cylinder Heads & Valvetrain ...

    www.americanmuscle.com/mustang-valvetrain-0508.html
    They help your motor breathe better and also make sure your Mustang gives top-notch throttle response. ... 2005, 2006, 2007, 2008, 2009 Mustangs; V6, GT, Bullitt, Shelby GT500, ... 2005-2009 Mustang GT Cylinder Heads & Valvetrain Components ... (6).Ford Racing SOHC 3V 4.6L Head Changing Kit (05-10 GT) $76.00.

    Mustang Camshaft Facts & Technical Information ...

    www.americanmuscle.com/camshaft-tech-guide.html

Feb 08, 2016 | Ford Cars & Trucks

Tip

I get code p0700 after an OBDII scan.


P0700 Transmition Control system is the transmission control module.
The transmission control module is a separate computer module, you need to read codes stored on transmission control module.

If there are no transmission code stored, then there is a bad Transmission Control Module (TCM) ground circuit or a bad TCM. In that case the ground to TCM must be tested, and TCM eventually replaced.

Faults that can cause troubles when shifting from first to second gear are : transmission fluid, speed sensor, TPS, transmission shift solenoid, gear box problem, TCM, neutral switch, torque converter problem.

The best thing to do is scanning TCM codes.

on Dec 02, 2009 | Jeep Wrangler Cars & Trucks

1 Answer

05 mustang gt motor is racing ,by itself and there's a squealing noise. I've replaced alternator, tps , and both vct solenoids.


I had the same problem on a Pontiac. It turned out to be a vacuum leak. ANY air leak behind the throttle body will be understood as an open throttle. I found mine by flooding the intake manifold with smoke.

Nov 05, 2014 | Cars & Trucks

1 Answer

I got a kia sorento need to find the tcm


TPS goes bad on these models, replace it with the redesigned TPS. Part number: 35102 39000FFF

Mar 26, 2013 | 2004 Kia Sorento

1 Answer

The tool light comes on after traveling


The dealer should be able to read the trouble code.

This can occur with the TCM (Transmission Control Module) and/or ECU program. This may require either a re-flash or a program download to the ECU. The ECU program is not a warranty item, but is typically in the $75 to $100 range.

However there is a Technical Service Bulletin (TSB) for the “wrench light”.

TSB 05-14-4

This article supersedes TSB 05-09-15 to update the Issue and Dealer Coding.

FORD:
2003-2005 Thunderbird
2005 Crown Victoria, Mustang
2004-2005 Explorer, F-150
2005 E-Series, Expedition, F-Super Duty
LINCOLN:
2003-2005 LS
005 Town Car, Navigator
MERCURY:
2005 Grand Marquis
2004-2005 Mountaineer

ISSUE:
Some vehicles built 11/29/2004 and prior may exhibit the wrench light on with both P2106 and P2135 diagnostic trouble codes (DTCs).

ACTION:
Replace the throttle position sensor (TPS) following the instruction sheet included in the TPS service kit. Reprogram the powertrain control module (PCM) to the latest calibration using WDS release B36.11 and higher, or B37.2 and higher. This new calibration is not included in the B37 CD. Calibration files are also available at www.motorcraft.com

I hope this helps!

May 06, 2010 | 2005 Ford F 250 Super Duty

1 Answer

My 05 v6 mustang coupe 44,000 miles. the cd


I had this problem in my 05 GT at about 50K miles, and had to get the stereo replaced. (It was covered by my extended warranty.) They have to send the old unit back to the factory to get the CDs out but will get them back to you when in a week or 2.

Jan 29, 2010 | 2005 Ford Mustang

1 Answer

What does fault code PO122


A P0122 code means that the the car's computer has detected that the TPS (throttle position sensor) is reporting too low a voltage. It coud be a bad TPS, or a wire problem.

Oct 28, 2008 | 1997 Ford Mustang Cobra

1 Answer

Mustang codes


Go to your local dealer and ask him to re-store your software, it should work.

Jun 17, 2008 | 2005 Ford Mustang

Not finding what you are looking for?
2005 Ford Mustang GT Logo

150 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5467 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...