Question about Dodge Cars & Trucks

2 Answers

Where is shift solenoid on a 2007 dodge ram 1500

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 4,536 Answers

Buy a haynes manual for complete engine detail @ autozone

Posted on Apr 08, 2015

Ad
  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 31 Answers

I'm not positive on the 2007 specifically, but in most cases the shift solenoid is located inside the transmission fluid pan, above the filter. Drain the fluid/drop the pan, remove the transmission filter, and you SHOULD see the solenoid just above the front edge of the opening...

Again I'm not positive on the 07, this is just where they are located on most of the trucks I have encountered. On that note, before you open it up make sure you have a new filter & gasket and enough new fluid to fill the pan after servicing (normally 4-5 quarts will do it) keep in mind a service fill is considerably less fluid than the total fluid capacity of your transmission... good luck !

Posted on Apr 08, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 178 Answers

SOURCE: 1998 dodge 1500 wont shift

first of all standard or auto i am guessing its standed standard under drivers side hood near master cylinder there is a small clutch reservoir if there isnt enough fluid it wont extend the throw out bearing far enough for a shift because the clutch pedal is hitting the floor not enough fluid to extend the slave cylinder to drive the fork second faulty slave cylinder or throw out bearing as far as the light blown dash bulb or somone snipped the wire or took the bulb out

Posted on Sep 11, 2008

  • 35 Answers

SOURCE: 91 dodge ram 1500 3-4 transmission shift solenoid

Transmission shop next.

Posted on Mar 07, 2010

  • 14585 Answers

SOURCE: I have a 2007 Dodge RAM 1500. Where is the shift

All the shift solenoids are in the transmission. You will have to remove the oil pan from the bottom of the transmission to access these. All the solenoids are on a package/ housing. They come off as a unit. You can replace these one at a time, but you really need to know what your looking for. It could be a bad solenoid , bad wiring in the transmission, bad connection at the plug going to the transmission, bad wiring going to the transmission. Computers will pop out a code, but you have to check everything that is related to that sensor/ solenoid.

Posted on Aug 03, 2011

fireplaceres
  • 21 Answers

SOURCE: I have a dodge ram 1500 and yr 2007 and it sqeals only when breaking and it is not my brake pads

When were your pads replaced last? Aftermarket semi-metallic pads are all different. You could four sets of pads by the same manufacturer and three sets are fine and the forth set will squeal all of the time. If the brakes only make noise when you are applying pressure that is about all it could be. Your pads probably look new and still squeal. Try having your rotors resurfaced or scuffed up and see if that helps!

Posted on May 15, 2012

emissionwiz
  • 77169 Answers

SOURCE: change transmission solenoid on 2007 dodge ram 1500 5.7L hemi

All of the shift solenoids are on the transmission valve body.

Posted on Sep 25, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 dodge Ram 1500 will not shift in reverse has codes P0736 and P1790 ?


the 1790 is a range display code, make sure your shift linkage is adjusted correctly 0736 is reverse out of range (rpm) which could mean possible shift linkage, or solenoid problem, or worst case internal problem with low reverse clutch or band, check fluid condition and level if its burnt your most likely going to have an internal problem if not run a scanner for possible adjustment or solenoid failure

Oct 12, 2015 | 2006 Dodge Ram 1500

1 Answer

1994 dodge ram 1500 2wd wont shift out of 1st gear.reverse works


take bottom pan off clean out your pressure sensor .. tends to get mini metl flakes caught up in there wich is also a bad sign that your tranny is going out but this will buy you atleast another 2 to 3 months

Apr 14, 2013 | 1997 Dodge Ram 1500 Club Cab

1 Answer

Change transmission solenoid on 2007 dodge ram 1500 5.7L hemi


All of the shift solenoids are on the transmission valve body.

Sep 25, 2012 | Cars & Trucks

1 Answer

I have a 2007 Dodge RAM 1500. Where is the shift solenoid located.


All the shift solenoids are in the transmission. You will have to remove the oil pan from the bottom of the transmission to access these. All the solenoids are on a package/ housing. They come off as a unit. You can replace these one at a time, but you really need to know what your looking for. It could be a bad solenoid , bad wiring in the transmission, bad connection at the plug going to the transmission, bad wiring going to the transmission. Computers will pop out a code, but you have to check everything that is related to that sensor/ solenoid.

Aug 03, 2011 | 2007 Dodge Ram 1500 Quad Cab Sport

3 Answers

2003 dodge ram 1500 quad cab will not shift out of park


There is what is called a shift interlock mechanism. It is suppose to keep you from putting it into gear withut putting your foot on the break.

Do a quick test. See if your brake lights come on when you press the brake peddle. If they do, you will have to go into the wireing of the brake switch and see if power is coming out of the switch to the interlock solenoid. If power is going to the solenoid, then you have a bad solenoid.

Hope this helps.

Apr 10, 2010 | 2004 Dodge Ram 2500

1 Answer

Dodge ram 1500 2001 codes coming up 0753 1757 1762 1765 trans not shifting proper trans in drive wont shift to lower gears automaticly


0753 is shift solenoid A, electrical problem.as for the other codes they should start with a zero not a one. if they started with a 0757 that means shift solenoid B,stuck in on position. 0762 means shift solenoid C,stuck in on position. 0765 means shift solenoid D,malfunction

Jan 20, 2010 | 2001 Dodge Ram 1500 Truck 2WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...