Question about Ford Cars & Trucks

1 Answer

How do you replace the windshield washer pump on 2008 ford focus, wipers work but no spray comes out

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 11,041 Answers

The hose could be clogged ! Do you know where you add the washer fluid ? Somewhere on the bottom of that plastic bottle is the washer pump .
Removal and Installation
> WARNING: Windshield washer solution contains methanol, which is poisonous. Observe all cautions and warnings indicated on label of washer solution container. Failure to follow these instructions may result in personal injury.
> CAUTION: When replacing the windshield washer pump be careful not to damage the rubber grommet.
> CAUTION: Do not operate the windshield washer pump before filling the reservoir. Failure to do so could result in premature pump failure.

  1. NOTE: When installing the reservoir, the filler neck must be lubricated using a water-based lubricant.
    Remove the bolt and the windshield washer reservoir filler neck.
  1. Remove the RH fender splash shield. For additional information, refer to Section 501-02 .
  1. Remove the foam filler and remove the retainer.
  1. Remove the 2 screws and the accessory drive splash shield.
    • To install, tighten to 5 Nm (44 lb-in).
  1. Remove the nut, 2 bolts and position the A/C accumulator aside.
    • To install, tighten to 9 Nm (80 lb-in).
  1. Unclip the A/C lines from the inner fender well.
  1. Drill out the rivet and remove the bracket.
  1. Remove the 2 bolts, slide the windshield washer reservoir assembly forward to release it, and position the washer reservoir aside.
    • Install the upper bolt followed by the lower bolt, and tighten to 5 Nm (44 lb-in).
  1. Disconnect the windshield washer tube assembly from the pump and release the windshield washer tube assembly from the washer reservoir.
  1. Disconnect the electrical connector from the windshield washer pump.
  1. Release the wiring harness from the reservoir, and remove the washer reservoir.
  1. To install, reverse the removal procedure.

Posted on Apr 07, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace windshield washer pump on 2008 ford focus, wipers work but no spray comes out


You can use a needle to clean out the tiny holes in the hood sprays. That usually fixes it. Then spray some air through the bottle.
Otherwise, the bottle comes out easily and the pump is in or under the bottle.
Hope this helps.

Apr 07, 2015 | Ford Cars & Trucks

2 Answers

2010 Reg Ford Focus 5 door hatch rear screen wash not working. Front is OK. How do I fix it?


the washer fluid could be empty / the fuse for the wiper blew / the relay went bad /if you tried to use the wipers without clearing ice away you blew the fuse/ if you just put water in instead of washer fluid it's frozen/ if the wiper works and there is windshield fluid in the tank and not water and all fuses are good the pump motor for the fluid went and is easy to change

Feb 25, 2015 | Ford Cars & Trucks

2 Answers

My windshield washer is not working correctly.


Assuming you have washer fluid and you can hear the pump with no flow at the main line I would guess the turbine has separated from the pump shaft.

Sep 30, 2014 | 2006 Ford Focus

3 Answers

My 2006 Dodge Dakota windshield washer fluid does not spray. I checked the washer pump and it works. The fuses are all good. And the wipers work. When I press the windshield washer button inside the truck...


If the pump works, something should be flowing thru the hose to the spray nozzles.
And if the pump works, everything electrical is working.
How do you know the pump works ?

Apr 14, 2013 | 2006 Dodge Dakota

1 Answer

2008 Ford Focus Windshield Washer Fluid level is full but it does not spray on windshield. Had it in for service and they cleared the lines, but it still won't spray on windshield. It cost a lot of money...


check the water pump placed under the water bottle or switch the car on dont start it run the water if you dont hear the sound of water pump running its either the pump damaged or something to do with the fuse or wiring

Jan 25, 2011 | Ford Focus Cars & Trucks

1 Answer

I have a 2008 Grand Prix. Windshield washer is


follow the hoses to the hood or wiper arm (i dont know where your spray nozzles are)and disconnect hem and press the spray button. if it sprays your nozzles are plugged, if not its your pump motor.

Feb 16, 2010 | 2008 Pontiac Grand Prix

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

384 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...