Question about GMC Envoy
Are here: Left side: 1.blue 2.Lt.blue 3.Brown 4.brown/white 5. yellow/black. Right side: 6.Blue/white 7. Lt.Green/black 8. TanReplaced BCM with a 15065293. I believe it calls for a 15122670. So far ive done a passkey relearn, just to get it away from impound lot. I still need to reprogram it. Thus far I have no windows, seats, auto lights interior, no rear park lights. Total pain in the rear. Any help would be incredible..
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: I have broken wire harness on the back of my Heater/AC automatic climate control. The black harness on the back has 11 different colored wires. Do you know which color wires go on which pins in the ba
Check the dealer to see if they have a pig tail to wire in. if so the new pigtail should have same wire color for matching up.
Posted on Jun 14, 2012
Regardless of colour coding, please follow the following instructions (require multimeter):
Note: Attach multimeter earth wire (black) to the vehicle body. Convenient places may be the metal ignition barrel, the vehicle's car arial plug, cigarette socket body etc.
1) Testing for voltage with key out of the ignition, locate the permanent positive wire. This will wire into the yellow wire on your new stereo. The yellow wire circuit powers the stereo's memory.
2) Testing for voltage again. This time you are testing for a wire which only offers power with the ignition turned on. This one will wire into the red wire on your new stereo, and will power the unit only with the ignition on.
3) Now you know which your vehicle's positive wires are you can now test for an earth wire. Switch the multimeter to the resistance setting. There is one setting which will allow a buzzer to sound once you find continuity. With the ignition off test each wire until you get a buzz and a low resistance reading. This should be your earth wire. Double check this with the ignition in the on position. It should remain the same. If it changes to a positive with the ignition on and with the vehicle's lights switched on, then this is the dimmer feed for the stereo's screen. If you unintentionally found the dimmer feed, then you can ignore this wire, and search again for a wire which only offers an earth.
Now you have your power and earth wires located and can wire these into your stereo before continuing.
4) Next you need to use the stereo's balance and fade controls to allow only one speaker output to work from the stereo. So let's start with Left Front speaker output only. turn the stereo volume to mid way so that you can hear when you have connected to the right speaker. bare the remaining wires on the car side and test combinations of the remaining wires until you find the front left speaker of the car. Wire your stereo's wires once you find the correct connections.
5) Repeat the above steps with all remaining wires, remembering to adjust your stereo's balance and fade controls to only allow one speaker output at a time, to ensure the only one possible channel to work and help you identify which of the car's wires power the speaker you have selected.
Before re-assembly of the dash panel, check that your stereo and all functions work properly, being sure to use your fade and balance controls again to test all speakers individually.
If you want to be extra careful and wire the vehicle's speakers positive and negative, according to your stereo's outputs, not that this makes much difference on standard stereo arrangements, then follow this next step:
Make sure you can see the speakers themselves and connect a 1.5 volt AA or AAA battery to the speaker wires. If the speaker's cone pushes forwards, then the wire you connected to the battery's + terminal is indeed the positive wire and should be wired as such. If the speaker does the reverse, then you have the wires the wrong way around. Do not repeat this test for extended periods as damage may be caused to the speaker circuit.
Tip: Always solder all connections and insulate well from each other. Stereo connections can corrode over time and are prone to movement behind the dash. Poor connections may cause faults and low quality sound.
Posted on Oct 30, 2012
Tips for a great answer:
Jun 13, 2016 | 2013 Buick Regal
May 08, 2016 | Cars & Trucks
Nov 28, 2015 | 2004 GMC Envoy SLT
Aug 13, 2015 | Saturn Cars & Trucks
Feb 20, 2014 | 2003 GMC Envoy
Oct 10, 2013 | 2004 GMC Envoy
Sep 18, 2011 | 2002 GMC Envoy
Apr 11, 2017 | 2007 GMC Yukon
17 people viewed this question
Usually answered in minutes!