Question about 2008 Nissan Frontier

1 Answer

I have a 2008 nissan frontier and when im in or out of my truck you can hear it lock and unlocking itself. The keys are in my hand so im not pressing anything, would anyone know why or how to fix?

Posted by Anonymous on

  • robert wales Apr 07, 2015

    take it to shop that has the capability or the dealer to have this done.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 4,977 Answers

This sounds like it could be a problem with the BCM or security module that controls the locks when you push the remote. it may need to be reset or it has another problem. have you tried to reset the key fobs to the module.

Posted on Apr 07, 2015

  • Anonymous Apr 07, 2015

    No i haven't tried that, and i wouldnt know how exactly to do that.

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

pal03246
  • 723 Answers

SOURCE: 2000 nissan frontier crew cab gas tank

there may be a recall on the sending unit, but the VIN # needs to be checked by the local Nissan dealer to see if the campaign applies to this truck. Tha campaign is for the fuel pump sending unit, not the gas tank, however in some cases, where the sending unit bolts brake, dealer will have to put a new gast tank into it. it also corrodes on top, where the sending unit seals the gas tank and it turns on the check engine light for a evap small leak, bacause the sending unit is not sealing properly, bacuse of all the rust build up on top of the tank. Good luck.post result.

Posted on Aug 18, 2008

Murphybanton
  • 2004 Answers

SOURCE: key fob for hyundai elantra not working

Please dont worry yourself so much the security locks needs to be reprogrammed to enable it work effectively. Same happens to other vehicles as well.

Consult Hyundai garage close to you or if you have it in your manual.

Good luck.

rate this.

Posted on Apr 14, 2009

  • 233 Answers

SOURCE: Remote Door Lock/Unlock will not work.

At first look, I would have guessed that your battery in the door opener was dead, but that is not the case. I suggest driving to a nearby Chevy dealer and ask one of the salesman if he/she can help. They have always been helpful to me. If not try another one as they are in business to sell not only cars, but service also. They will be your best bet to fixing it. :D

Posted on Jun 08, 2009

  • 14585 Answers

SOURCE: 2000 nissan frontier knock sensor code & distributor

no but the knock sensor does send a signal the ecm and it will ****** or advance the distributor timing

Posted on Jun 14, 2010

  • 248 Answers

SOURCE: key fob will not activate anything. can't

I too had this problem. I finally found out that my problem was the result of the metal contacts that touch the circuit board when you push the buttons had worn out. To correct my problem, I purchased a small pad that slides right inside the remote and fixes all the buttons. Since then, my remote has worked problem free for the past 3 months. The company that makes the pads is KEYLESSFIX. The following link will take you to the actual website:

http://www.keylessfix.com/keylessfixcom/

Please remember to rate my solution. Thanks!

Posted on Feb 01, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My horn does not work on my 2008 Nissan frontier. I replaced the relay and checked all fues...


Horn itself may be bad. Mine was and as soon as I replaced it the horn now works.

Dec 27, 2016 | 2008 Nissan Frontier

1 Answer

Starting frontier after manually shifting automatic gear shifter without key?


The shifter lever must be in either neutral or drive. The Frontier has an unlock mechanism to shift the lever if is locked.

Oct 08, 2014 | 2000 Nissan Frontier

1 Answer

Key wont unlock door


You need a new door lock actuator.

Feb 15, 2014 | 2002 Nissan Frontier Crew Cab

1 Answer

Nissan frontier starter binds the flywheel


You need to put shims in between the starter and the engine block.You should be able to pick them up at your local auto parts store.

Oct 31, 2012 | Nissan Frontier Cars & Trucks

2 Answers

Lock function works but lights do not come on and horn does not blow when lock or alarm buttons are pressed on the remote.


try this one. hold both lock and unlock buttons for about 10 seconds. the truck should beep and the light should flash twice. that switches alarm modes from quiet to loud/on and wiseversa.( hope i spelled that one right).

Dec 31, 2010 | 2008 Nissan Frontier

1 Answer

I have a 2001 nissan frontier and the key is in the lock position in the ignition. how do i unlock and start the car.


If the wheel was turned a certain way to engage the wheel lock when turned off, turn the wheel all the way to the right or left while trying to turn the key. Chances are the column lock is catching preventing you from turning the key. You may have to use force but do not use too much force if it does not seem like it will give.

It should "pop" free while turning on the wheel.

Jun 07, 2009 | 2001 Nissan Frontier Crew Cab

1 Answer

I need to know how to reprogram a keyless entry remote for a 2003 nissan frontier..


IMPORTANT: Before entering programming mode, have in possession all of the
transmitters you will be using on the vehicle. Once you program the
transmitter, all previous codes will be erased from the memory. The other
transmitters will not be functional until you program the transmitters
again.

1. Close and lock all doors with the driver's side power lock/unlock
switch.

2. Insert key into ignition and remove it from the ignition key cylinder
at least six times within 10 seconds. Your Hazard
Lamps will flash if you have performed this step successfully. NOTE:
Withdraw key completely from ignition cylinder
each time. If this procedure is performed too fast, system will not
enter programming mode.

3. Insert key into the ignition cylinder and turn to the ACC position.

4. Within 5 seconds, push ANY button on the remote transmitter. Your
Hazard Lamps should flash. NOTE: Do not press
the button more than one time in the above step. If the button is
pressed more than one time, the programming
procedure will not be successful.

5. If there are any remaining transmitters (including the old ones),
unlock then lock all doors using the driver's side
power lock/unlock switch and within 5 seconds, push ANY button on the
next remote. Your Hazard Lamps should
flash. Repeat this step for each transmitter (including any existing
transmitters).

6. Turn the key to the OFF position, remove keys from the ignition, unlock
doors using the driver's side power lock/unlock switch and open the driver
side door.

Apr 11, 2009 | 2003 Nissan Frontier Crew Cab

3 Answers

2002 nissian frontier tailgate is stuck


First thing: Try using the key to move to the locked and then to the unlocked position. If this works, open the tailgate... This also pretty much tells you what the root cause problem is, which is a pressed-in plastic post working its way out (see below).

If no bedliner, just remove metal plate inside tailgate and actuate by hand inside to open. If bedliner, first use a small screwdriver to carefully (don't scratch paint) push in latches at either side of tailgate to open/lower tailgate (if locking/unlocking as above did not work to lower gate and gain access). Next, use two blade screwdrivers to pry out the "buttons" that hold the ends of the tailgate liner where they wrap around the sides, then remove bedliner piece and metal plate, etc.

Once you have access to inside of tailgate, you will see how the mechanism works by pulling up and down on the handle while observing. You will probably find that the slide mechism that locks and unlocks the mechanism has been allowed to move such that it cannot unlock/allow movement of the latching mechanism. This is usually the result of the pressed in plastic anchor being worn/loose. I had some success with cleaning thoroughly with alcohol or brake cleaner, allowing to dry and then using super glue to hold it firmly in all the way. Still have to hold handle up when closing gate and keep key on hand to unlock every time opening, but it was a free repair...

Apr 02, 2009 | 2002 Nissan Frontier Crew Cab

Not finding what you are looking for?
2008 Nissan Frontier Logo

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

723 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...