Question about 2008 Volvo S40

1 Answer

Code fault 0061, 0071 damper position to faulty position 2008 Volvo S40?

Posted by Anonymous on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 47 Answers

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: volvo s40 radio

hi lneed code for radio s40 volvo 2001

Posted on Aug 17, 2008

  • 273 Answers

SOURCE: Volvo 2008 S40, how do you reset the service

you need to take it to a dealership for resetting

Posted on Jun 06, 2009

  • 333 Answers

SOURCE: 2001 volvo s40 trouble code P0015

This is a common issue particularly with vehicles that have had some neglect to the oil change routine. The VVT solenoid on the top of the valve cover gets clogged with thickened or sludged oil.

Replace the VVT solenoid and gasket with a new unit and clear the codes.

Posted on Sep 10, 2009

  • 333 Answers

SOURCE: Radio code for volvo s40

If the display says "Off" the radio is locked from incorrect code input.

You need to leave the key in the accessory position with the radio on (display reads 'Off') for about two hours.
After that it should ask for he code again. You have three tries before it locks again.
Some radios are different, but typically you use the knob to adjust the numbers, push the knob in to move to the next number

Posted on Sep 11, 2009

ZJLimited
  • 17970 Answers

SOURCE: what causes the following faults code on 2004 volvo S40 :ECM-250A LONG TERM-FUEL TRIM:UPPER LIMIT,BCM-0100 COMMUNICATION PROBLEM WITH ECM,EPS-0082 ENGINE STATUS FAULTY SIGNAL,CCM-001 COMMUNICATION CON

Check, test or replace MAF sensor.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Posted on Jul 09, 2012

Testimonial: "my volvo "check engine light"problem solved after replacing MAF sensor. thanx to FixYa!!!!!!!!! "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Volvo s40 code moteur p0102 inf svp


code p 102 refers to mas air flow (MAF) sensor/ volume (VAF) sensor ---low input===causes --wiring short to ground --MAF/VAF sensor ---ECM
code p 103 refers to MAF/VAF sensor ---high input====causes --wiring short to positive ---MAF/VAF sensor---ECM

Aug 20, 2016 | 2002 Volvo S40

1 Answer

2007 volvo S40 will not start after replacing alternator belt, smell gas after trying to start


I am thinking faulty injectors and/or excessive fuel pressure in the fuel manifold . Run fault codes again ensuring that the cables used and the procedure to connect is adhered to as there will be a fault code recorded but not being read

Mar 22, 2014 | 2007 Volvo S40 2.4i Sedan

1 Answer

Accelerator pedal position sensor circuit


you need to take it off and on the side there is a hole spray some dw40 or switch cleaner in the hole and shake it about a bit in side the sensor. then drain it out. and leave to dry. should be fine then. give it a few turns before putting back on and then set it back to bottom and refit to the markings on the side of the intake. if there is none make some before removing it.

Jan 22, 2014 | 2008 Volvo S40

1 Answer

Fault code 1600


code 1600 refers to throttle position (TP) sensor-communication error. Cause wiring---poor connection---TP sensor---ESP control module---ECM
code 1000 refers to barometric pressure (BARO) sensor --signal high. Cause---wiring short to positive---BARO sensor.

Apr 08, 2013 | 2008 Volvo S40 2.4

1 Answer

What causes the following faults code on 2004 volvo S40 :ECM-250A LONG TERM-FUEL TRIM:UPPER LIMIT,BCM-0100 COMMUNICATION PROBLEM WITH ECM,EPS-0082 ENGINE STATUS FAULTY SIGNAL,CCM-001 COMMUNICATION CONTROL...


Check, test or replace MAF sensor.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jul 09, 2012 | 2004 Volvo S40

1 Answer

2000 s40 has erratic idle. Feels like it's surging


This seems similar to a Volvo C70 which i have worked on......the fault was the Mass Air Flow Meter was faulty........does it do this in all the gears?

Mar 13, 2010 | 2000 Volvo S40

1 Answer

I am looking for the method of getting fault codes from my 1997 volvo s40 1.8l as am failing to start the engine but am getting fuel and a spark


On my volvo phase2 the code access point is when sitting in drivers seat its below under dash by were your left Knee/shin is.

Feb 17, 2010 | 2000 Volvo S40

1 Answer

Engine management light volvo s40 problem


sounds like thats correct. fault camshaft position sensor or wiring to ecm is prob

May 14, 2017 | 2000 Volvo S40

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

311 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...