Question about Cars & Trucks

1 Answer

Flush not working but pump is - Cars & Trucks

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 52,175 Answers

How do you flush a car /truck

Posted on Apr 07, 2015


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How much atf for full flush in 2000 Rodeo 3.2 v6

can take at least 20 liters for a full flush as the oil is being pumped in as the engine is running and is being pumped out at the same time to flush the transmission as well as the torque converter
best take it to an auto transmission shop that does a full flush procedure

May 31, 2017 | Cars & Trucks

1 Answer

My windscreen washers are not working but the pump is running I have tried to flush out system

if the pump is working then there is a blockage. you say you have tried to flush the system but have you checked and cleaned the spray nozzles of dirt, this is usually where the blockage is.

Sep 23, 2014 | Cars & Trucks

1 Answer

Car running hot after changing thermostat

they sell many flush products the best ive found is wynns products FOLLOW THE DIRECTIONS on the bottle , make sure fan r fans r working properly maybe even check flow from water pum sometmes pump fins courod and dont pump like they should . if flush doesnt work pull radiator take to shop have them clean and rod the core .

Jul 26, 2012 | 2005 Chevrolet Impala LS

1 Answer

The antifreeze reservoir is full and doesn't hasn't fluctuated, yet the vehicle is getting very hot and smokey smelling. the pressure gauge doesn't reflect overheating butts clear at the antifreeze isn't...

is the water pump working and circulating the antifreeze. if it is working, I would flush out the system and replace the thermostat before refilling system. you can buy radiator flush at any auto parts store. you can back flush system through radiator. just follow directions on back of flush bottle. have a good one!!

Nov 10, 2010 | 1999 Plymouth Voyager

1 Answer

What is the best way for to flush out my radiator? I bought a flush and fill kit but it is asking me to cut hoses and I don't feel comfortable doing that. Can you also show me a picture where the water...

The best thing to do with a flush kit on a Montana is to replace a section of the heater hose with a piece about 3 feet long, that way you can install the flush valve and have plenty of room to work with it and the hose will be long enough that it won't kink from the elbows that they use. The water pump is located under the first pulley that you see on the front of the engine. If you were standing in front of the van, it would be the pulley closest to you.

Sep 09, 2010 | 2001 Pontiac Montana

1 Answer


A weak water pump, faulty thermostat, and or bad radiator. You can try with the simple and replace the thermostat and flush out the cooling system with radiator flush, just follow the instructions on the radiator flush bottle. Preston has a radiator flush product that works really good on cleaning up any corrosion, causing the restriction of coolant throughout the engine and radiator. If this does not help, then its and good chance that your going to have to replace the water pump.
Thank you for using Fixya and good luck.

Mar 22, 2010 | 1993 Nissan 240SX

1 Answer

Put stop leak in rad

the only thing I can recommend is to put in a flush tee not the hose going to the water pump but the one going to the engine open up the radiator and drain that first then fill with water get some radiator flush and run the car about ten minutes drain that out using the flush tee and a garden hose and run till it is clear with the engine running after clear close drain plug on radiator and fill with antifreeze and make sure to get all air bubbles out and you should start getting some heat and if you don't after doing all this replace the heater core but check the hoses coming from the heater core to make sure one of them is not plugged

Jan 29, 2009 | 1997 Mercury Mountaineer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

80668 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15483 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides