Question about 2010 Ford Escape XLT

Open Question

Ford escape 2010 rear wiper fuse number 19 blow Is someone had this problem before

Motor is brand new

Posted by on

  • Richard Gagnon
    Richard Gagnon Apr 08, 2015

    wiper work for a while , intermitant problem, whithout moving rear door hindge

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
johnny5846
  • 379 Answers

SOURCE: 2003 Ford Explorer-Rear Wiper Motor-How to Replace?

the plastic panel pops off , if you had a trim removal tool it would be nice but it can be improvised , they are just tension clips , get some kind of lever behind the panel and give it a pop , once the plastic panel is off its pretty much self explanatory from there , a connector and couple small bolts , now the outside has nut under the w/w blade , a piece of the arm cover pops up to access the nut , remove w/w arm , then a grommet and under the grommet is a bigger nut that helps hold the motor onto the door/hatch , when reinstalling before you put the w/w arm back on run the wiper and make sure it shuts off and in the park position . should be a piece of cake .

Posted on Jan 05, 2009

Ad
bunnydawg
  • 5158 Answers

SOURCE: Ford Escape rear wiper doesn't remove anything

rear wipers are horrid for that... i just bent the wiper arm a little toward the window... works fine

Robert

Please take a moment to rate this solution thanks

Posted on Jan 30, 2009

chuck943
  • 783 Answers

SOURCE: HOW DO I REPLACE A REAR WINDOW WIPER ON 2005 FORD ESCAPE?

Remove the rear pivot arm.
Lift the pivot arm to the upright position.
Slide the locking tab out.
Pull up and remove the pivot arm.
Remove the rear wiper motor shaft nut cover.
Remove the rear wiper motor shaft nut.
Remove the rear wiper motor cover.
Remove the rear wiper motor bracket nut.
Remove the bolt and the rear wiper motor.

Posted on Jan 30, 2009

  • 3 Answers

SOURCE: replace rear wiper motor on ford focus 02 plate

any auto parts store sells a chiltons manual on your ford focus!!! i think they are around $12 dollars it will explain step by step instructions..........................

Posted on Feb 01, 2009

  • 4340 Answers

SOURCE: need to replace rear wiper blade on a 2006 ford

These days the entire blade and holder assembly is replaced, not just the blade. The holder separates from the arm.

Posted on Nov 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear wiper stopped


Do you know how to use a volt meter ? Need to check for voltage at the motor ! , need a wiring diagram. Most of the time other people on here will tell you to check the fuse's , that doesn't end up being the cause ! Most of the time it's the motor or a wiring problem ! I have seen the wire in side the rubber boot ,when you open the rear hatch break causing a no power situation to the motor . If you open the rear hatch ,door ,lift gate , what ever you call it . If you look when it is open there is a rubber boot connecting the body to the door , there are wires in side . There have been known to break ! This next part is a FORD pinpoint test. This is how ford says how to check !
PINPOINT TEST B: THE WIPERS ARE INOPERATIVE - REAR WINDOW Test Step Result / Action to Take B1 CHECK CIRCUITS CBP43 (GY) AND SBP19 (BU/RD) FOR VOLTAGE
  • Key in OFF position.
  • Disconnect: Rear Wiper Motor C476.
  • Key in ON position.
  • Measure the voltage between rear wiper motor C476-3, circuit CBP43 (GY), harness side and ground; and between rear wiper motor C476-4, circuit SBP19 (BU/RD), harness side and ground.
    >
  • Are the voltages greater than 10 volts?
Yes
GO to B2 .

No
VERIFY SJB fuse 43 (5A) and fuse 19 (25A) are OK. If OK, REPAIR the circuit(s) in question. TEST the system for normal operation. B2 CHECK CIRCUIT GD150 (BK/WH) FOR OPEN
  • Key in OFF position.
  • Measure the resistance between rear wiper C476-1, circuit GD150 (BK/WH), harness side and ground.
    >
  • Is the resistance less than 5 ohms?
Yes
GO to B3 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. B3 CHECK THE MULTI-FUNCTION SWITCH
  • Key in OFF position.
  • Disconnect: Multi-function Switch C202.
  • Carry out the multi-function switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  • Did the multi-function switch pass the component test?
Yes
GO to B4 .

No
INSTALL a new multi-function switch. REFER to Section 211-05 .

Mar 14, 2015 | 2010 Ford Expedition EL

1 Answer

2004 ford taurus wagon rear wiper will not work, but wiper fluid does


Your wiper and wiper fluid motors are different operation. The fluid one is a pump and the wiper motor only operates the wipers. Should check and see if you are getting power to the wiper motor if you are and the wiper does not work then you may need a new wiper motor.

Nov 27, 2014 | 2004 Ford Taurus

1 Answer

Rear wiper not working on 2010 ford escape. how do i fix it?


Mine is neither working. the motor has gone. you have to replace it.

May 20, 2014 | 2010 Ford Escape

1 Answer

Air fan won't work


It is doubtful but maybe.. Check all the fuses and see if you have a blown fuse. If so replace fuse and see if that fixes your problem.

Jan 30, 2013 | 2010 Ford Escape XLT

1 Answer

Rear wiper and washer wont work on 2005 Ford Escape


check fuse check for power at wireing harness at wiper motor if power bad wiper motor

Feb 13, 2011 | Ford Escape Cars & Trucks

1 Answer

Need to know what fuse goes to my rear windshield wiper \


The fuse panel is located on the right-hand side of the center console, by the instrument panel. Remove the panel cover to access the fuses. Check position 21, 10AMP (*) Rear wiper motor, Rear wiper washer (colored in the diagram)...

zjlimited_683.jpg

(*) Mini-Fuse

Hope helps (remember to rate this answer)

Feb 11, 2011 | 2006 Ford Escape

2 Answers

2005 Ford Escape Front windsheild wipers dont work. whenever the car is turned on the fuse will blow over and over. got the car looked at and was told i need to replace the combo switch. what else could be...


motor may be bad for the windshield wipers, you can disconnect and turn wipers on and see if blows the fuse, as it is in the switch then it should blow as soon as you turn them on. Hope this helps Tim

Oct 19, 2010 | 2005 Ford Escape

3 Answers

How easy is it to replace the front wiper motor on a 2004 ford escape ? Where is it located ?



Front Wiper Motor
Removal & Installation

NOTE A new wiper motor assembly comes with the linkage arm installed.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the windshield wiper mounting arm and pivot shaft
    WARNING Do not remove the wiper motor linkage arm from the wiper motor assembly. If the arm is removed, the wiper arms may not park in the correct location.
    NOTE Use a suitable tool to separate the wiper linkage arm from the wiper mounting arm and pivot shaft assembly.
  3. Remove the 3 bolts and the wiper motor.

    7f7866e.gif

    Fig. Wiper motor and linkage

To install:
  1. Install wiper motor and bolts.
  2. Tighten wiper motor bolts to 10 ft. lbs. (13 Nm).
  3. Install windshield wiper mounting arm and pivot shaft.
  4. Check wiper operation.

Rear Wiper Motor
- Removal & Installation
  1. Remove the rear pivot arm.
  2. Remove the rear wiper motor shaft nut cover
  3. Remove the rear wiper motor shaft nut.
  4. Open the lift gate window.
  5. Remove the rear wiper motor cover trim panel.
  6. Disconnect the electrical connector.
  7. Remove the 2 rear window wiper motor nuts
  8. Remove the rear window wiper motor.

    79be491.jpg
    Fig. Rear wiper motor view-2008 model shown, other years similar

To install:
  1. Install rear wiper motor and tighten mounting nuts to 62 inch lbs. (7 Nm).
  2. Reconnect the electrical connector.
  3. Install wiper motor cover trim panel.
  4. Install rear wiper pivot arm tighten nut to 53 inch lbs. (6 Nm).
  5. Install shaft nut cover.
  6. Check wiper operation.

Good luck (remember rated this post).

Feb 25, 2010 | 2004 Ford Escape

2 Answers

Rear wiper does not work at all. front wipers work fine. rear washer works


1. check the fuse to the rear wiper motor
2. check for power to rear wiper motor at the motor (power wire going in to the wiper motor with rear wiper switch on)
If you have good fuses & have power going in to the rear wiper motor...
3. Pull old rear wiper motor and install a new rear wiper motor.
Thank you please drive thru......

Feb 26, 2009 | 2001 Ford Expedition

1 Answer

HOW DO I REPLACE A REAR WINDOW WIPER ON 2005 FORD ESCAPE?


Remove the rear pivot arm.
Lift the pivot arm to the upright position.
Slide the locking tab out.
Pull up and remove the pivot arm.
Remove the rear wiper motor shaft nut cover.
Remove the rear wiper motor shaft nut.
Remove the rear wiper motor cover.
Remove the rear wiper motor bracket nut.
Remove the bolt and the rear wiper motor.

Jan 29, 2009 | 2005 Ford Escape

Not finding what you are looking for?
2010 Ford Escape XLT Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...