Question about Cars & Trucks

1 Answer

I cant get the. Motor away from the bell housing

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 2,039 Answers

Bonjour linda if you did remove all the bolt the doll pin have corosion on them and are jam or centering pin are stuck pry it of

Posted on Apr 07, 2015

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

How to replace the bell housing of a 1989 jeep wrangler 4-cyl 4x4?

why are you replacing the bellhousing?,it means you are going to have to pull out the motor or the gearbox/transfer case,whichever is easieast

Jul 04, 2014 | 1989 Jeep Wrangler

1 Answer

Torque converter ta

Torque converter is located in the bell houseing of the gear box (Automatic) You need to remove the inspection cover from the bottom of the bell houseing & it has several bolts attaching it to the flywheel (ring gear) of the engine. You will need to turn the motor by hand to get all those bolts. Then you have to remove the whole gearbox. then you can remove the converter from the bell houseing. MAKE SURE IGNITION IS OFF WHEN TURNING MOTOR BY HAND

Jun 16, 2012 | 1984 Chevrolet Chevy

1 Answer

I have a 2004 jeep grand cherekee laredo with a bad crank sensor.i can start truck but it stalls right away.i m trying to find sensor to replace it,all the diagrams ive looked at are useless.i simply cant...

what is the size of your engine and model. did you call or go to auto-zone they should be able to give you a diagram or tell you where it is. if all fails you can always go to dealer for a diagram of sensor, this should be at no cost to you. have a good day !!

Apr 28, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Trying to change a stater cant find the bolts on top

the top bolts come in from the rear of the bell housing. They these bolts mount both the bell housing to the block and the starter motor to the block. Under neath just line up wich mount bolts are close to the starter and undo them, possibly 2 that hold them. once remove starter should fall straight into your hand

Jan 22, 2011 | 1997 Ford Expedition

2 Answers

Where is the crankshaft position sensor on a 2002 crysler Sensor(Cant Find It)

well it is near the to of bell houseing on trans side it should be coming out of bell housing at trans

Aug 14, 2009 | 2005 Chrysler Town & Country

2 Answers

Oil pan stuck

If this is a 4WD it is easiest to remove the front differential an the pan will drop right down.

Jul 21, 2009 | 1999 Chevrolet S-10 Pickup

2 Answers

Looking for the bell housing area on a 1998 land rover discovery

The Bell housing is the cover of your flywheel---it's attached between the engine and transmission and is shaped like a bell.

Mar 31, 2009 | 1998 Land Rover Discovery

1 Answer

Cant find the location of the thermostat 2000 silverado 4.3 engin

Follow your Upper Radiator Hose to the Motor. It will Connect to a Bell Housing that is Mounted on the Top of the Block. Remove this Bell Housing and the Thermostat is Underneath the Bell Housing. Install the New one the EXACT same way that this one can out. Please Rate My Response! Thanks!

Jan 30, 2009 | 2000 Chevrolet Silverado

1 Answer


Just follow the Upper Radiator Hose from the Radiator the the Motor and where it attaches to the Motor there is a Bell housing. Reove the Hose and Bell Housing and it is Underneath the Bell Housing. Looks just like a U.F.O.

Jan 14, 2009 | 2000 Dodge Caravan

2 Answers

I cant find the starter inside my car.

The bell housing of your gear box is bolted to the engine. Either at the front or rear of the engine you will find the starter motor bolted to the engine adjacent to the bell housing for your gearbox. The starter motor has to engage with the flywheel to start your car and the clutch is also bolted to the fly wheel.

Dec 02, 2008 | 1998 Mitsubishi 3000GT

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides