Question about Dodge Cars & Trucks

1 Answer

Distributor replacement on a 1997 dodge average 2.5 v6 what do I have to do to do it right?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 77 Answers

Main thing to do is make sure you take note of the direction of the rotor and base location before removal. Take a picture with your cell phone.

Posted on Apr 07, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: 1997 dodge ram 1500 v6,i have a misfire,ive changed plugs,wires,distributor cap,rotor cap,fuel pump,rollover valve,coil,still has a miss

you can try changing the ignition coil, I own a 97 Dodge 1500 and mine did the same and thats what i had to do.

Posted on Oct 08, 2008

SOURCE: I hve a 1997 dodge dakota V6 just did full tuneup

Start with a Minimum Air Rate adjustment, use of scanner is preferred to put system in bypass mode for proper setting. Or for quick set, (engine off) knock out plug for throttle set screw and turn in (clockwise) 1/4 turn to start with, disconnect battery for two minutes, reconnect and start vehicle.

Posted on Jan 19, 2014

  • 11095 Answers

SOURCE: Have a 1997 dodge average 2.5 v6 24 value I have replaced crankshaft positioning sensor but still no spark to plug wires can someone help?

Did you check for battery + voltage at the coil ? an is the PCM turning the coil on an off ?

Posted on Apr 05, 2015

  • 14585 Answers

SOURCE: I have a 1997 dodge average 2.5 v6 24 value its not getting spark to plug wires have replaced crankshaft positioning sensor and still no spark please help.

You need to check wiring first. After that would be the ECM. You need wiring diagrams/pinouts and a volt/ohm meter.

Posted on Apr 05, 2015

  • 2355 Answers

SOURCE: What will fix the spark to plug wires on a 1997 dodge average 2.5 v6 24 value have already replaced crankshaft position sensor still not starting?

Could be a bad coil

Posted on Apr 05, 2015

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 dodge Dakota pickup truck. it stalls sometimes at idle, and running down the road 70 mph it just cuts out, and dies.


Start with the most basic item: check your compression. Low compression gets lower when an engine gets warm.

Jan 02, 2017 | 1997 Dodge Dakota

5 Answers

I have no plug wire spark 1997 dodge average 2.5 v6 24 value.have already replaced crankshaft positioning sensor on it and still no spark to the wires


Sounds like a bad distributor. Had you pulled a spark plug out you may have found them wet with gas after cranking. If they are wet the crank sensor is working since both injector pulse and coil pulse rely on crank signal.

The distributors are known week points in the ignition system and used to be common when theses cars where still on the road. A reman will run you $250 U.S.

Apr 05, 2015 | 1997 Dodge Avenger

2 Answers

I have a 1997 dodge average 2.5 v6 24 value its not getting spark to plug wires have replaced crankshaft positioning sensor and still no spark please help.


You need to check wiring first. After that would be the ECM. You need wiring diagrams/pinouts and a volt/ohm meter.

Apr 05, 2015 | 1997 Dodge Avenger

1 Answer

I have a 1997 dodge avenger 2.5 V6 I pulled the distributor out to replace with a new one and did not mark the position of the rotor button...how do I make sure I have the new rotor button in the corr


You would have to find the number one spark plug Remove the wire and plug. Manually turn the motor over to the compression stroke. Insert the distributor so that the rotor generally faces the number one plug.

Jan 29, 2014 | 1997 Dodge Avenger

2 Answers

Firing order of 2003 dodge grand caravan


For the 2003 Dodge Caravan (and Grand Caravan) ALL 3.3L V6 Engines (including the Flex Fuel): Also for 3.8L V6 Engines:

Firing Order:
1-2-3-4-5-6

Cylinders:
........(back).......
|...1....3....5...|
______________
|...2....4....6...|

Ignition Coil:
.......(back)
electrical connection
...........|
..........V
5........1........3
2........4........6
.......(front)

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

Jun 06, 2010 | 2003 Dodge Grand Caravan AWD

1 Answer

94 Dodge Dakota no spark no fuel


replace pickup coil in the distributor

Apr 27, 2010 | 1997 Dodge Dakota

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...