Question about Cars & Trucks

1 Answer

We replaced the sparkplugs and wires, camshaft sensor, crankshaft sensor, timing belt, and oil pressure sensors on our 2005 PT Cruiser Touring Edition, non-turbo. Error P 0522 still shows. Any ideas?

Posted by on

  • paulmacintyre
    paulmacintyre Apr 06, 2015

    This code is set when the PCM detects low oil pressure from the oil pressure sending unit. If you have replaced this unit I would next have an actual oil pressure reading performed with a guage to determine pressure before you hrow any more money at it

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 1,087 Answers

So you have to have the error code cleared sometimes by a dealership if you have an ORileys or Autozone in your town they will clear the old stored codes free.

Posted on Apr 06, 2015

  • Leslie Sine Apr 07, 2015

    The car is still non-operational, so I don't think it's a matter of simply clearing the code.

    It tries like heck to turn over but it just won't start.

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
rockitman187
  • 2559 Answers

SOURCE: 2004 chrysler pt cruiser starter motor removal

You may sneak it out with small fingers with out pulling out the starter.

If starter removal is required,Just unhook the battery cables,Remove the 2 bolts holding the starter on.


Please rate this a fixya

Posted on Feb 08, 2009

  • 412 Answers

SOURCE: where can I find the crankshaft position sensor on

IT IS LOCATED IN THE BLOCK BELOW THE STARTER..UNPLUG CONNECTOR AND 1 BOLT..IT MAY BE STUCK IN BLOCK..SPRAY WITH PENETRATING OIL..MOVE BACK AND FORTH PULL OUT OF BLOCK

Posted on Jul 14, 2009

  • 5370 Answers

SOURCE: Will not start. 03 PT Cruiser (4-spd NOT Turbo)

Yes replace the battery temp sensor as per the error code p0516 showing up.The battery temperature sensor is located under the vehicle battery and is attached (snapped into) a mounting hole on battery tray. The sensor is located under the battery on drivers side of vehicle. The ABS battery tray will need the left and right edge lips ground off to allow the 10 inch long battery to sit in the tray. The tray should be retained so that the battery temperature sensor will continue to function. ---------- This will help.Thanks.Helpmech.

Posted on Feb 12, 2011

  • 3 Answers

SOURCE: location crankshaft position sensor 2004

Its located on the engine block usually the front

Posted on Mar 24, 2011

hotrodshop
  • 106 Answers

SOURCE: location speed sensor pt cruiser 03 touring car do

It sounds like the module is in limp mode. The speed sensor is most likely the cause, but it can be some other things as well. A scan will give a code stating the problem area.

The speed sensors are on the side of the trasmission that faces the front of the vehicle. There are 2 of them, and they are the same sensor. One is an input speed sensor located closest to the engine, the other is the output speed sensor.


hotrodshop_0.png

Posted on Jun 17, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P0016


P0016 Crankshaft Position - Camshaft Position Correlation.
____________
VAS 5054A best quality version

Apr 24, 2013 | 2007 Chrysler PT Cruiser Touring Hatchback

1 Answer

Camshaft position sensor correlation bank 1 code


timing belt is off by a tooth or two. you probably didn\'t have to replace the coolant sensor; that code sets whenever the sensor is disconnected and the ignition is turned on; and it needs to be reset by disconnecting the battery or with a code reader. anyway, the crank/ cam sensors are out of sync. if you\'ve got the twin cam engine, they are a royal pain to get the belt to lay properly on the two cams.

Apr 15, 2013 | 2007 Chrysler PT Cruiser Touring Hatchback

1 Answer

2007 pt cruiser p0118 code came up, replaced the sensor and still showing up


Is there 2 Sensor's on your Car?

One for the Gauge and one for the Computer?

Apr 10, 2013 | 2007 Chrysler PT Cruiser Touring Hatchback

1 Answer

I replaced the camshaft position sensor P0340, now the OBD is reading a PO0016


Causes that bring up code P0016 may include:
  • Timing chain stretched, or timing belt skipped a tooth due to wear
  • Misalignment of timing belt/chain
  • Tone ring on crankshaft slipped/broken
  • Tone ring on camshaft slipped/broken
  • Bad crank sensor
  • Bad cam sensor
  • Damaged wiring to crank/cam sensor
  • Timing belt/chain tensioner damaged
  1. First, visually inspect the cam and crank sensors and their harnesses for damage. If you notice broken/frayed wires, repair and recheck.
  2. If you have access to a scope, check the cam and crank patterns. If a pattern is missing, suspect a bad sensor or a slipping tone ring. Remove the cam gear and the crankshaft harmonic balancer and inspect the tone rings for proper alignment and make sure they're not loose or damaged or that they haven't sheared the key that aligns them. If they are properly installed, replace the sensor.
  3. If the signal appears normal, then check the timing chain/belt for proper alignment. If it's misaligned, check for a damaged tensioner that may have allowed the chain/belt to slip a tooth or several teeth. Also check that the belt/chain isn't stretched. Repair and recheck.
Hope this helps

Feb 06, 2012 | 2005 Chrysler PT Cruiser

1 Answer

Whats the position of the crankshaft position sensor on 2005 pt cruiser non turbo


P0344 CHRYSLER - Camshaft Position Sensor Intermittent Interruption Bank 1 Sensor 1
Possible causes - Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty Camshaft Position Sensor
- Faulty starter motor
- Starting system circuit

Dec 14, 2011 | 2005 Chrysler PT Cruiser

1 Answer

Changed the timing belt and camshaft sensor on a 2005 pt crusier pretty sure its timed correctly because the car seems to run fine and revs high with no problems although it still throws P0016 code even...


What the P0016 code means. P0016 is the OBD-II generic code indicating that the camshaft position sensor for bank 1 does not correlate to the signal from the crankshaft position sensor. The camshaft timing is out of position due to the timing chain jumped teeth. The camshaft phaser is out of position due to problems with phaser.

May 22, 2017 | 2005 Chrysler PT Cruiser

2 Answers

2002 pt cruiser replaced camshaft position sensor still not starting wires are good


if you replace the crank sensor and camshaft sensor you need a DRB scan tool reprogram sensor to pcm.so they will work.

Dec 06, 2009 | 2002 Chrysler PT Cruiser

2 Answers

After changing the camshaft censor and the car still wont start what could be the problem also is there a fuse that needs to be replaced this is a 2004 pt cruiser the code say its the camshaft censor also...


P0016 crankshaft/camshaft timing misalignment
p0340 camshaft sensor

intermittent crankshaft sensor

PCM detects an error when the camshaft position is out of phase with the crankshaft position

Sep 26, 2009 | 2004 Chrysler PT Cruiser

3 Answers

Code PO340


P0340 is a Crankshaft Position Sensor error. It determines firing order and is most likely the cause of your problem. It's mounted near the oil filter on the engine block. Below is a picture of how it appears in your car. Best of luck.
Greg


23ad084.gif

Jul 13, 2009 | 2005 Chrysler PT Cruiser

1 Answer

2002 pt cruiser Camshaft Sensor


change the crankshaft positon sensor in the rear of the engine above the oilfilter. Also check the wiring to this sensor, they have a problem shorting out. You have to change the camshaft and crankshaft sensors at the same time. Make sure you give your car a major tune up. Did you check yor starter?.........runjoe

Feb 04, 2009 | 2002 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...