Question about Cars & Trucks

1 Answer

Where is the MAP sensor on a 2002 Intrepid 2.7

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 2,899 Answers

The MAP sensor is usually close to the Throttle Body.
Hope this helps.

Posted on Apr 06, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
leetamara
  • 702 Answers

SOURCE: My 2002 Dodge intrepid has it engine light on

The MAP sensor and Knock Sensor are both very easily replaced. A better scanner will tell you which sensor is going bad on your transmission. An Autozone code reader will not tell you which sensor on the trans. is acting up. Most sensors on your trans. are very easity replaced as well. They just screw in and plug it. It's worth paying to get a "real" scan done. The trans. sensors are inexpensive and you can replace any other your listed sensors yourself.

Posted on Jul 11, 2008

old marine
  • 1985 Answers

SOURCE: dodge intrepid 2002

The knock sensor is threaded into the block of the engine, just below where the cylinder head sits. You will need to remove the intake plenum (upper and lower) to access this part.

Posted on Feb 05, 2009

Molson02536
  • 3854 Answers

SOURCE: Map sensor location

If you are looking at the motor from the front of the car it is on the right side of the plenum it has a wire hook up and it gets vacuum straight from the plenum its just a square box don't look like its important . Hope this makes some sense. 

Posted on Jul 01, 2009

  • 1810 Answers

SOURCE: how do i replace a( map) sensor -manifold air sensor

hayes has a great bible for your car i would sugest getting 1 and read a little

Posted on Jan 03, 2010

  • 15 Answers

SOURCE: need location of 2002 intrepid

The MAP sensor mounts to the driver side of the intake manifold plenum.0996b43f802022b9.jpg


Removal & Installation


  1. Remove the negative battery cable.
  2. Disconnect the electrical connector from the MAP sensor.
  3. Remove bolts from sensor.
  4. Remove sensor.


To install:

  1. Bolt sensor to intake.
  2. Attach electrical connector to sensor.
  3. Install the negative battery cable.

Posted on Jul 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Get codes p0068 and p0108


codes p0068 refer to Manifold pressure sensor/mass air flow sensor--throttle position correlation--causes ---wiring---map sensor---maf sensor--mechanical fault.
code p0108 refers to manifold absolute pressure(map) sensor/barometric pressure (BARO) sensor--high input. causes ---wiring short to positive---map sensor---baro sensor---ecm.

Mar 28, 2013 | 2002 Dodge Intrepid

1 Answer

Need location of 2002 intrepid map sensor and how to change it


The MAP sensor mounts to the driver side of the intake manifold plenum.0996b43f802022b9.jpg


Removal & Installation


  1. Remove the negative battery cable.
  2. Disconnect the electrical connector from the MAP sensor.
  3. Remove bolts from sensor.
  4. Remove sensor.


To install:

  1. Bolt sensor to intake.
  2. Attach electrical connector to sensor.
  3. Install the negative battery cable.

Jul 23, 2011 | 2002 Dodge Intrepid

1 Answer

I took off the air cleaner to try and replace one of the fuel evap hose now the car doesnt want to start.it will turn over wants to start but wont.did i do something wrong?


you probably forgot to reconnect the MAP sensor or the MAF sensor, check around the air intake and look for a disconnected sensor end.

Apr 27, 2011 | 2002 Dodge Intrepid

1 Answer

How do i replace a( map) sensor -manifold air sensor


hayes has a great bible for your car i would sugest getting 1 and read a little

Jan 03, 2010 | 2002 Dodge Intrepid

1 Answer

2002 Intrepid 2.7 motor just shuts off when stoping check engan light came on and code was a map sensor changed it still stoped running hade the light reset and it just came right back on this time...


check for vaccum leak at map sensor or anywhere else no vaccum to map will show up as bad because the computer watches the voltage on it and the vaccum changes that voltage , no vaccum meens no voltage change and computer throws the light on to let you know there's a problem somewhere.

Dec 27, 2009 | 2002 Dodge Intrepid

2 Answers

Map sensor


Driver side of intake manifold plenum, near dipstick area.

Dec 23, 2009 | 2002 Dodge Intrepid

1 Answer

2002 intrepid vacuum issue p0108


CODE PO108 IS MAP SENSOR CIRCUIT HIGH INPUT.

Aug 01, 2009 | 2002 Dodge Intrepid

1 Answer

I have a 2002 Dodge Intrepid. I received 2 error codes P0441 and P0155. I had a sensor replaced and now I am receiving 1 code a Po152. Can you please tell me what this means?


P0152 is o2 sensor 2/1 voltage high. Sensor 2/1 is your right bank upstream o2 sensor located in the manifold. Make sure it is pluged in.

Dec 26, 2008 | 2002 Dodge Intrepid

1 Answer

My 2002 Dodge intrepid has it engine light on


The MAP sensor and Knock Sensor are both very easily replaced. A better scanner will tell you which sensor is going bad on your transmission. An Autozone code reader will not tell you which sensor on the trans. is acting up. Most sensors on your trans. are very easity replaced as well. They just screw in and plug it. It's worth paying to get a "real" scan done. The trans. sensors are inexpensive and you can replace any other your listed sensors yourself.

Jun 30, 2008 | 2002 Dodge Intrepid

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...