Question about Cars & Trucks

1 Answer

When I am just about stoped the abs comes on and if I press brakes again it does not come on. I have a 2002 2500 chevy 4x4

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,218 Answers

This can be caused by a variety of reasons depending on make and model. If you have ONE newer tire than the rest, wet/slippery road conditions, loose/worn wheel bearing, poor connections at ABS sensors or bad sensors. I would have the system scanned to determine the affected wheel. In a lot of cases, especially on trucks, play in the wheel hub assembly is a major cause

Posted on Apr 06, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Abs light comes goes out then comes back after starting engine on a 2003 chevy S10 4x4


Check for proper opperation of vehicle wheel speed sensors and disk brakes in general ware fluid level that sort of thing
Also problems with coruse control or brake release switch could effect it

Aug 19, 2016 | Chevrolet S 10 Cars & Trucks

1 Answer

I have a 2003 chevy silverado 1500 4x4 no engine or abs light comes on but when i apply the brakes the brake pedal pulsates and pulls to the right just replaced front brakes didnt make a difference. but if...


pulsates ARE normal for this truck it means abs is working.
if truck pulls to the right then the LEFT brake caliber is not working right check to see if rusted up... also install NEW calb. BOLTS never reuse old one if one is bent calb. wont slide correctly

Oct 04, 2017 | Cars & Trucks

1 Answer

Does my truck have abs brakes? It is 4x4 1992 chevy 1500


Your truck is equipped with RWAL or rear wheel anti-lock. This just worked on the rear brakes(duh) but the speed sensor was taken from the speedometer drive at the transmission tailshaft, and would allow one rear wheel to lock as long as the speedo kept turning. Later models were improved with wheel speed sensors at each wheel.

Apr 06, 2010 | 1992 Chevrolet K1500

1 Answer

Truck not stoping and anti brake is working.


dosen't stop at all or just slow?, if the abs is working then you should feel the pulseing in the brake pedal just before tire lock-up, the tires will not lock-up with abs fully funtioning unless all four tires or two are in lock-up depending on the abs application, if abs fails it reverts it self to regular braking ability, hope this helps

Sep 14, 2009 | 2004 Chevrolet Silverado

1 Answer

Abs and brake light come on offten


check fluid if its good u may need to reset the computer, unhook battery for few min,try that.

Jul 03, 2009 | 2000 Chevrolet S-10

4 Answers

2001 Chevy Tahoe with ABS & Brake light on.


I hope you have the problem fixed by now, but, it is the ABS control under the truck. You need to go under the hood and open the fuse box and disconnect the 60 amp fuse for the ABS, this will turn it off before it burns up. This however will also cause the traction assist off light to stay lit all the time. To the fix the problem you can pay tons of money ($700 or so) to have the dealership install a ABS control and the problem will happen again over time. Or, remove it yourself, go on ebay and ship it off to a guy who repairs them for about $150 and you will never have the problem again. Also, if you wrap your cable ends with plastic and protect them good, you can still drive you truck while the part is being worked on. It takes about a week.

Nov 12, 2008 | 2001 Chevrolet Tahoe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...