Question about Plymouth Cars & Trucks

1 Answer

I have a 99 Plymouth Grand Voyager, the issue I am having is getting the antenna mount, off the fender, I have tried unscrewing it but it doesn't budge, the top of the mount is round with 4 indents.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Plymouth Master
  • 3,218 Answers

You need an antenna nut socket to effectively remove the nut without causing any damage to the nut or vehicles paint. If you are not concerned about nut chrome finish or paint damage, clamp visegrips to the nut.and it should release with minimal effort

Posted on Apr 06, 2015

  • John Campbell
    John Campbell Apr 12, 2015

    Ty, I'm not concerned about the on I need to take of the fender I just got, but I am of the one on the fender still on my van, very helpful

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

For a 1996 plymouth voyager sm V6 3.0 liter transmission control module and where is it located at?


It on the passenger side just behind the headlight mounted on the inner fender. 4 thumbs up is appreciated if this helps

Dec 01, 2010 | 1996 Plymouth Grand Voyager

1 Answer

1999 plymouth grand voyager speed sensors location


1999 Plymouth Truck Grand Voyager 2WD 3.8L MFI 6cyl
*
The Vehicle Speed Sensor is located Mounted on transmission
* The Sensor - Transmission Speed is located Mounted on transmission

Hope this help (remember comment and rated this).

Apr 20, 2010 | 1999 Plymouth Grand Voyager

2 Answers

I have a 1990 Ford Thunderbird, the radio gets power, the speakers get power, but i'm getting nothing but static. What is the issue? I've tried two separate head units, the amp is hooked up and so is the...


Try a new antenna temporarily--just hold the mast base in your hand. Water can enter the antenna cable from outside which shorts it out. Hope this helps!

Apr 04, 2010 | 1990 Ford Thunderbird

1 Answer

'99 Plymouth Grand Voyager fan switch issues


The problem is not with the switch, it's the blower motor resistor. The resistor is usually located in duct work near the blower motor. It will have 4or 5 wires going to it and is held in place with a couple screws. These things generate heat, so they put them in duct work so the fan blows air across them to keep them cool. Sometimes the plug gets hot and melts, you should be able to buy the resitor and the plug with wires (pig tail) from an auto parts store or a dealer. The resistors are usually about $50 the pig tail is about $30.

Dec 02, 2009 | 1999 Plymouth Grand Voyager

2 Answers

Where is the starter relay located? 93 plymouth grand voyger 3.3L New starter,but just clicks, will start after many tries.


Check drivers fender area, under hood, near strut mount. You should be able to hear and feel click in one of those relays. Check part #'s on them, they are usually same for 2 or 3, which allows you to use another to test circuit before replacing so you know.

Nov 25, 2009 | 1993 Plymouth Grand Voyager

1 Answer

Can i swap a 99 voyager trans.


no the 3.3 obviously smaller than the 3.8. you cant even swap engine mounts are diffrent so is the bellhousing on the tranny to the engine.

Jul 08, 2009 | 1998 Plymouth Grand Voyager

1 Answer

99 Plymouth Voyager Rear Bumper


If you look up from under you should see some push clips. if your removing entire bumper with rebar & all, it's probably about 4 nuts holding it to bumper shocks, but be sure to look near ends at fenders for push clips , and or screws, and across mid section. watch it, it's pretty heavy with the rebar attached so make sure you have everything ready & remove nuts last, with some help to hold it up.

Aug 05, 2008 | 1999 Plymouth Grand Voyager

2 Answers

Automatic belt tensionor


Same tensioner or a new one?

Jun 16, 2008 | 1999 Plymouth Grand Voyager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8211 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...