Question about Cars & Trucks

1 Answer

What is the correct wheel bearing torque for the

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 2,039 Answers

Yor mean for the cv joint or the bolt that hold the hub bearing tigh fully no strip

Posted on Apr 06, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1993 Mitsubishi Diamante. To replace inner wheel bearings. You need to remove the wheel, caliber and bracket, rotor, and hub correct? The wheel bearings are on the inside of the hub correct?


Yes. You have to press the bearing out. If you don't have the press tools. Best to take spindle to a shop and have them press the new one in. Don't know of renting the press tools. Don't forget to torque the axle nut.

Sep 14, 2014 | Cars & Trucks

1 Answer

2007 jeep compass 4wd light flashes overtemperature code after changing front wheel bearing


How tight did you make the nut holding the bearings onto the spindle? Did you change the bearing races too? Recheck the torque values to see if they are correct. an old race on a new bearing will cause temperature problems.

Jul 08, 2014 | 2007 Jeep Compass Limited

1 Answer

Front wheel bearing torque


Better late than never Brucy....CLICK HERE TO SEE YOUR WHEEL BEARING GUIDE. Repair Guides Front Suspension Wheel Bearings AutoZone com

Apr 02, 2014 | 2006 Pontiac Grand Prix

1 Answer

Front wheel bearing torque


The axle nut is 118 ft lbs
The other 3 bolts are a 75 ft lbs

Apr 02, 2014 | 2006 Pontiac Grand Prix

2 Answers

Driver side wheel bearing problems.


Torquing might be the problem.
If they are tapered bearings, you should snug them down then back the nut off a quarter turn or so. I usually turn the nut back until the locking pin will align with the hole in the spindle.

Jul 11, 2012 | Ford Cars & Trucks

1 Answer

Procedure for replacing rear whl brgs on a 2003 escape awd


4-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake shoes
    • Rear halfshaft nut and loosen the halfshaft from the hub
    • Wheel hub and place it in a vise
    • Inner wheel bearing race from the hub
    • Antilock Brake System (ABS) sensor bracket and move the sensor aside, if equipped
    • Parking brake cable from the steering knuckle
    • Brake line from the wheel cylinder and support the knuckle
    • Lower shock absorber nut
    • Lower ball joint by holding the ball joint stud
    • Upper ball joint
    • Coil spring while noting the location of the insulator
    • Steering knuckle cam
    • Steering knuckle
    • Snapring and press out the outer wheel bearing race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge

To install:

  1. Install or connect the following:
    • New wheel bearing into the steering knuckle
    • Snapring to the knuckle
    • Wheel hub
    • Steering knuckle cam and hand tighten the bolt
    • Coil spring
    • Shock absorber lower nut. Torque the nut to 85 ft. lbs. (115 Nm) for 2002-04 models; 129 ft. lbs. (175 Nm).
    • Upper ball joint. Torque the nut to 76 ft. lbs. (103 Nm).
    • Lower ball joint. Torque the nut to 76 ft. lbs. (103 Nm). Align the steering knuckle cam and torque the bolt to 85 ft. lbs. (115 Nm).
    • Brake line to the wheel cylinder. Torque the brake line bracket bolt to 15 ft. lbs. (20 Nm) and the brake line fastener to 11 ft. lbs. (15 Nm).
    • Parking brake cable to the backing plate. Torque the bolt to 16 ft. lbs. (22 Nm).
    • ABS sensor bracket. Torque the bolt to 80 inch lbs. (9 Nm), if equipped
    • Halfshaft nut. Torque the nut to 214 ft. lbs. (290 Nm).
    • Brake shoes
    • Rear wheel
    • Negative battery cable
  2. Fill and bleed the brake system.
  3. Check and adjust the wheel alignment as needed.

2-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake drum
    • Wheel hub nut
    • Wheel hub
    • Inner wheel bearing race from the hub
    • Snapring
    • Wheel bearing outer race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge 06017-esca-g93.gif

      Rear hub removal
      06017-esca-g94.gif

      Inner wheel bearing removal-rear hub/bearing
      06017-esca-g95.gif

      Rear wheel bearing removal-2wd
      06017-esca-g96.gif

      Rear wheel bearing removal-4wd

To install:
Install or connect the following:

  • Wheel bearing in to the knuckle
  • Snapring
  • Wheel hub into the wheel bearing
  • Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
  • Brake drum
  • Rear wheel
  • Negative battery cable
    06017-esca-g97.gif

    Rear wheel bearing installation
    06017-esca-g98.gif
    hope this helps if so send testimonial comment or even any other questions you have

Jan 16, 2011 | Ford Escape Cars & Trucks

1 Answer

How do i change out front wheel bearings


Compare to a rear wheel drive care, the bearings are totally different from the tapered style from the old days. Those where much easier to remove and don't require special tools. FWD bearings have high temp grease which is thicker and doesn't breakdown into a soupy state when it gets hot.

  • You'll need an air hammer and the correct sizes of metric sockets
  • You need to remove the CV joint nut which is torqued at least 120lbs psi on the spline part
  • You'll need a long 1/2" breaker bar for leverage
  • You'll also need a 1/2" torque wrench
  • At least a 10 ton hydraulic bench press and corresponding flanges to push out the old bearing
  • If you have a bearing tool you might get away without a press
  • Must have factory manual with torque specs
  • If you don't have all of the above mentioned tools then I'd suggest to forget the idea doing it on your own, you'll need tons of power just to start the bearing out of the wheel bearing housing (carrier).

Feb 17, 2010 | Toyota Avalon Cars & Trucks

1 Answer

What are the torque specs. for a 2003 dodge dakota front wheel bearings? 2 wheel drive rear antilock brakes 3.9


Below is a chart from the Dodge service manual. The correct torque for the front wheel bearing is 163Nm or 120ft lbs
b05861a2-5afa-4624-a1a5-a0265bbf5db2.jpg

Oct 05, 2009 | 2003 Dodge Dakota Club Cab

2 Answers

Audi a4 tdi 51 plate


ring the main dealer and ask for torque setting they should tell u

Oct 17, 2008 | 2001 Audi A4

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...