Question about 2011 Hyundai Accent

1 Answer

Have to pump clutch to get it to work - 2011 Hyundai Accent

Posted by on

  • william
    william Apr 06, 2015

    cylinder is full

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Hyundai Master
  • 1,173 Answers

Either slave cylinder or master has leaked fluid, you may be able to fill system to get by for a while

Posted on Apr 06, 2015

Testimonial: "cylinder is full it connects to master only one fluid fill tank"

  • D. E. Hev Apr 06, 2015

    then you probably need to replace cylinder or rebuild it

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Air con will not work. Honda civic 2010


if air con is not working it could be the clutch in the ac pump, if you dont use the air con much or use it alot you can either have a seized clutch or a work clutch, without the clutch engaging the pump will not work and not flow around the system, when ac is engaged the idle on the engine will drop slightly.

Aug 07, 2017 | Honda Civic Cars & Trucks

1 Answer

Clutch has to be pumped to even get in gear then any gear to drive


Its probably the slave cylinder, try bleeding it and if that doesn't work you'll probly need a new one. They cost about 20-30 bucks

Mar 27, 2013 | Pontiac Firebird Cars & Trucks

2 Answers

5 speed Jeep Liberty clutch barely engages when vehicle first start.


If your clutch is hydraulic uses a master cyl. and a slave cyl. It sounds like the slave cyl. but could be both.

Aug 24, 2012 | 2002 Jeep Liberty

1 Answer

Clutch pedal on the floor ive checked the flid in the master cylinder and it is full is it the clutch tht has gone


pump it rapidly, maybe have to pick it up with your hand, its possible the clutch master is bad, as long as it was working normally before this happened. If it pumps up and feels normal after rapidly pumping I would suspect the clutch master cylinder is bad.

Aug 30, 2011 | 2003 Land Rover Freelander

2 Answers

What does it mean when i have to pump the clutch to get it to work and it has fluid in it


If you have to pump the clutch to get it to work, it means that the clutch fluid needs replacing........the clutch fluid is exactly the same a s brake fluid and must be changed evry 2 years.

If it is not changed, then it breaks down into water and its other ingredients, the water boils off when it gets too hot, and it creates a spongy clutch pedal, that requires you to continuallly pump it to get to work.

I would suggest that you buy some new brake/clutch fluid and blled the clutch.

If you are unsure how to do this, get back and let me know and I will post a procedure for you !!!!!

Feb 21, 2011 | 1996 Mazda Protege

2 Answers

Remove clutch fan dodge dakpta 4.7


This one does require a tool to loosen the fan clutch from the water pump shaft. Part of the tool holds the pulley and the other part is spanner wrench used to loosen the clutch. An important note on these fan clutches: Once you have the fan clutch off DO NOT let it lay with the rear side of the fan pointing downward as the silicone fluid that provides the "clutch" action can drain into the bearing and cause the clutch not to work. Once you have the clutch off just lean the fan and clutch against something so it is standing upright just as it is when it's bolted to the water pump until you are ready to put it back on. Hope this helps you out a bit!

Jul 11, 2010 | 2001 Dodge Dakota

1 Answer

Clutch was working but had to pump up to make work after sitting for a time and now wont pump up. clutch is not working now.


Hi, there seems to be a problem with the hydraulic clutch actuators, you should checkt the hydraulic cylinder driven by the clutch pedal for operation. If this cylinder is working, the problem hast to be the other cylinder operating the clutch.

Jun 25, 2010 | 1990 Chevrolet K1500

1 Answer

1994 Altima clutch master and slave replacement


easy replace both parts then fill the clutch reservoir,crack slave cly bleeder to let gravity bleed let 1 to 2 reservoirs flow through,tighten bleeder and pump clutch pedal,pump 4 or 5 times hold down pedal get 2nd person to crack bleeder while pedal is down,tighten bleeder before releasing pedal,should work fine

Nov 04, 2009 | 1994 Nissan Altima

1 Answer

Pulling a fan clutch assembly from a GMC 4.3 water pump?


First remove the fan from the clutch. There should be four to six bolts holding the fan to the clutch. The clutch is held on to the pump with four bolts. remove the four bolts to remove the clutch. I've included a pic of the pump to indicate the four mounting holes. Not sure if the link will work.

http://www.1aauto.com/scripts/view_full_image.php?image_url=http://images.1aauto.com/EWP/1AEWP00011.jpg&description_id=1090439

Aug 10, 2009 | 1996 GMC Sonoma

1 Answer

Water pump replacement


Get a wrench that fits on the fan clutch. Most auto part stores will have a fan clutch removal tool.

It works the best if you put the wrench onto the fan clutch and then hit it with a hammer in the dirction to take the clutch off. Sometimes it might take multiple tries to break the clutch loose.

Aug 05, 2008 | 1999 Dodge Durango

Not finding what you are looking for?
2011 Hyundai Accent Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...