Question about Cars & Trucks

1 Answer

How to manually open the slide out on a 2002 springdale XML 38 ft by keystone

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 45,422 Answers

There is a crank someplace for it check your maual

Posted on Apr 06, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace timing belt on 2002 kia spectre


Removal & Installation

1.5L, 1.6L (VIN 5) & 1.8L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Remove the accessory drive belts.
  4. Remove the alternator.
  5. Remove the water pump and crankshaft pulleys.
  6. Remove the timing belt guide plate.
  7. Remove the upper and lower timing belt covers.
  8. Position the crankshaft so that the timing mark is aligned with the timing mark on the engine.
  9. Verify that the I and E mark on the camshaft pulley align with the mark on the cylinder head.
    NOTE
    Do not move the crankshaft or camshaft once the timing marks have been correctly positioned.
  10. If the timing belt is to be reused, mark the direction of rotation on the timing belt.
  11. Remove the timing belt tensioner pulley.
  12. Remove the timing belt.


26088909-0r3idicjw2hp5z0o4sqjrbpc-4-0.gif


26088909-0r3idicjw2hp5z0o4sqjrbpc-4-1.gif


26088909-0r3idicjw2hp5z0o4sqjrbpc-4-3.gif
To install:
  1. Install the timing belt tensioner pulley, move the tensioner to its furthest point and tighten the lockbolt.
  2. Install the timing belt onto the pulleys, as follows, crankshaft pulley first, then the idler pulley, exhaust camshaft pulley, intake camshaft pulley, and the tensioner pulley.
  3. Loosen the tensioner pulley and allow the tensioner spring to apply tension on the belt, then tighten the lockbolt to 28-38 ft. lbs. (38-51 Nm).
  4. Rotate the crankshaft clockwise 2 turns and be sure all marks are still correctly aligned.
  5. Install the remaining components in the revere order of the removal noting the following torque specifications:

    Crankshaft pulley: 9-13 ft. lbs. (12-17 Nm) Water pump pulley: 9-13 ft. lbs. (12-17 Nm)
  6. Connect the negative battery cable.

Feb 10, 2016 | 2002 Kia Spectra

1 Answer

Where can I get an owners manual for a Keystone Montana 5th wheel


Well Keystone is still in business, so you could go to their website and download a copy. Or check with a keystone dealer.

Aug 06, 2014 | Cars & Trucks

1 Answer

Where do I find the timing marks on pulleys?


in the factory service manual FSM.

or

login to

alldata.com

and read all the steps



3VZ-FE (and 2vz)
this is your engine. and has many steps

key is timing and proper belt tension and is free running engine.



quote

Prior to timing belt removal, make sure all the match-marks are there-2VZ-FE and 3VZ-FE engines

less photos:

the crank mark is CR -line

the cam pulleys, 3v pulley to R-cam mark

and 3v pulley to L-cam mark. (photos are best).





  1. Remove the timing belt.


If the timing belt is to be reused, draw a directional arrow on the timing belt in the direction of engine rotation (clockwise) and place matchmarks on the timing belt and crankshaft gear to match the drilled mark on the pulley.



  1. With a 10mm hex wrench, remove the setbolt, plate washer and the No. 1 idler pulley.


  2. Remove the crankshaft timing pulley, if it can NOT be removed by hand, use two flat bladed tools. Position shop rags on the components to prevent damage.


TO INSTALL:



  1. Turn the crankshaft until the key groove in the crankshaft timing pulley is facing upward. Slide the timing pulley on so that the flange side faces inward.


  2. Apply bolt adhesive to the first few threads of the No. 1 idler pulley setbolt, install the plate washer and pulley and then tighten the bolt to 25 ft. lbs. (34 Nm).


  3. Install the timing belt on the crankshaft timing, No. 1 idler and water pump pulleys.


If the old timing belt is being reinstalled, make sure the directional arrow is facing in the original direction and that the belt and crankshaft gear matchmarks are properly aligned.



  1. Install the lower (No. 1) timing cover and tighten the bolts.


  2. Align the crankshaft pulley set key with the key groove on the pulley and slide the pulley on. Tighten the bolt to 181 ft. lbs. (245 Nm).


  3. Install the No. 2 idler pulley and tighten the bolt to 29 ft. lbs. (39 Nm). Check that the pulley moves smoothly.


  4. Slide the left pulley, facing the flange side outward. Align the knock pin hole of the camshaft with the knock pin of the timing pulley, then install the knock pin. Tighten the left camshaft timing pulley bolt to 80 ft. lbs. (108 Nm).


  5. Set the No. 1 cylinder to TDC again. Turn the right camshaft until the knock pin hole is aligned with the timing mark on the No. 3 belt cover. Turn the left pulley until the marks on the pulley are aligned with the mark on the No. 3 timing cover.


  6. Check that the mark on the belt matches with the edge of the lower cover. If not, shift it on the crank pulley until it does. Turn the left pulley clockwise a bit and align the mark on the timing belt with the timing mark on the pulley. Slide the belt over the left pulley. Now move the pulley until the marks on it align with the one on the No. 3 cover. There should be tension on the belt between the crankshaft pulley and the left camshaft pulley.


  7. Align the installation mark on the timing belt with the mark on the right side camshaft pulley. Hang the belt over the pulley with the flange facing inward. Align the timing marks on the right pulley with the one on the No. 3 cover and slide the pulley onto the end of the camshaft. Move the pulley until the camshaft knock pin hole is aligned with the groove in the pulley and then install the knock pin. Tighten the bolt to 55 ft. lbs. (75 Nm).


  8. Position a plate washer between the timing belt tensioner and the a block and then press in the pushrod until the holes are aligned between it and the housing. Slide a 1.27mm (3VZ-FE 1.5mm) Allen wrench through the hole to keep the push rod set. Install the dust boot and then install the tensioner. Tighten the bolts to 20 ft. lbs. (26 Nm). Don\'t forget to pull out the Allen wrench!


  9. Turn the crankshaft clockwise two complete revolutions and check that all marks are still in alignment. If they aren\'t, remove the timing belt and start over again.


  10. Install the right engine mount bracket and tighten it to 30 ft. lbs. (39 Nm).


  11. Position a new gasket and then install the upper (No. 2) timing cover. refer to the illustration for bolt positioning.


  12. Install the spark plugs.


  13. On the 2VZ-FE, install the right engine mount insulator. Tighten the bolt to 47 ft. lbs. (64 Nm), the bracket nut to 38 ft. lbs. (52 Nm) and the body nut to 65 ft. lbs. (88 Nm). Install the No. 1 stay and tighten it to 38 ft. lbs. (52 Nm). Install the No. 2 stay and tighten the bolt to 48 ft. lbs. (66 Nm) and the nut to 38 ft. lbs. (52 Nm).


  14. On the 3VZ-FE, install the control rod and tighten the bolts to 47 ft. lbs. (64 Nm). Install the right stay and tighten it to 23 ft. lbs. (31 Nm).


  15. Install and adjust the drive belts.


  16. Install the fender apron seal and the wheel.


  17. On the 3VZ-FE, install the No. 2 stay and tighten the bolt to 55 ft. lbs. (75 Nm), the nut to 46 ft. lbs. (62 Nm). Install the No. 3 stay and tighten it to 54 ft. lbs. (73 Nm).


  18. Install the coolant overflow tank and the washer tank.


  19. Install the power steering reservoir tank and the cruise control actuator.


  20. Connect the battery cable, start the car and check for any leaks.


end quote.

Feb 27, 2014 | 1993 Toyota Camry V6

1 Answer

I dont know how to line up my cams, witch dots do i line up


Manual is not clear either, but do you have "3V" marks on the gears? You have the 3VZ engine, so I would use those.

jturcotte_1952.gif

To install:
  1. Turn the crankshaft until the key groove in the crankshaft timing pulley is facing upward. Slide the timing pulley on so that the flange side faces inward.
  2. Apply bolt adhesive to the first few threads of the No. 1 idler pulley setbolt, install the plate washer and pulley and then tighten the bolt to 25 ft. lbs. (34 Nm).
  3. Install the timing belt on the crankshaft timing, No. 1 idler and water pump pulleys.

If the old timing belt is being reinstalled, make sure the directional arrow is facing in the original direction and that the belt and crankshaft gear matchmarks are properly aligned.
  1. Install the lower (No. 1) timing cover and tighten the bolts.
  2. Align the crankshaft pulley set key with the key groove on the pulley and slide the pulley on. Tighten the bolt to 181 ft. lbs. (245 Nm).
  3. Install the No. 2 idler pulley and tighten the bolt to 29 ft. lbs. (39 Nm). Check that the pulley moves smoothly.
  4. Slide the left pulley, facing the flange side outward. Align the knock pin hole of the camshaft with the knockpin of the timing pulley, then install the knock pin. Tighten the left camshaft timing pulley bolt to 80 ft. lbs. (108 Nm).
  5. Set the No. 1 cylinder to TDC again. Turn the right camshaft until the knock pin hole is aligned with the timing mark on the No. 3 belt cover. Turn the left pulley until the marks on the pulley are aligned with the mark on the No. 3 timing cover.
  6. Check that the mark on the belt matches with the edge of the lower cover. If not, shift it on the crank pulley until it does. Turn the left pulley clockwise a bit and align the mark on the timing belt with the timing mark on the pulley. Slide the belt over the left pulley. Now move the pulley until the marks on it align with the one on the No. 3 cover. There should be tension on the belt between the crankshaft pulley and the left camshaft pulley.
  7. Align the installation mark on the timing belt with the mark on the right side camshaft pulley. Hang the belt over the pulley with the flange facing inward. Align the timing marks on the right pulley with the one on the No. 3 cover and slide the pulley onto the end of the camshaft. Move the pulley until the camshaft knock pin hole is aligned with the groove in the pulley and then install the knock pin. Tighten the bolt to 55 ft. lbs. (75 Nm).
  8. Position a plate washer between the timing belt tensioner and the a block and then press in the pushrod until the holes are aligned between it and the housing. Slide a 1.27mm (3VZ-FE 1.5mm) Allen wrench through the hole to keep the push rod set. Install the dust boot and then install the tensioner. Tighten the bolts to 20 ft. lbs. (26 Nm). Don't forget to pull out the Allen wrench!
  9. Turn the crankshaft clockwise two complete revolutions and check that all marks are still in alignment. If they aren't, remove the timing belt and start over again.
  10. Install the right engine mount bracket and tighten it to 30 ft. lbs. (39 Nm).
  11. Position a new gasket and then install the upper (No. 2) timing cover. refer to the illustration for bolt positioning.
  12. Install the spark plugs.
  13. On the 2VZ-FE, install the right engine mount insulator. Tighten the bolt to 47 ft. lbs. (64 Nm), the bracket nut to 38 ft. lbs. (52 Nm) and the body nut to 65 ft. lbs. (88 Nm). Install the No. 1 stay and tighten it to 38 ft. lbs. (52 Nm). Install the No. 2 stay and tighten the bolt to 48 ft. lbs. (66 Nm) and the nut to 38 ft. lbs. (52 Nm).
  14. On the 3VZ-FE, install the control rod and tighten the bolts to 47 ft. lbs. (64 Nm). Install the right stay and tighten it to 23 ft. lbs. (31 Nm).
  15. Install and adjust the drive belts.
  16. Install the fender apron seal and the wheel.
  17. On the 3VZ-FE, install the No. 2 stay and tighten the bolt to 55 ft. lbs. (75 Nm), the nut to 46 ft. lbs. (62 Nm). Install the No. 3 stay and tighten it to 54 ft. lbs. (73 Nm).
  18. Install the coolant overflow tank and the washer tank.
  19. Install the power steering reservoir tank and the cruise control actuator.
  20. Connect the battery cable, start the car and check for any leaks.

Jul 18, 2011 | 1992 Toyota Camry V6

1 Answer

What is the rod bearing torque setting for 2002 2.2 chevy cavalier


Rod bearing torque for a 2002 Cavalier with a 2.2L engine is 38 Ft/Lbs.

Dec 27, 2010 | 2002 Chevrolet Cavalier Coupe

1 Answer

Diagram(power-rpm-torque-bsfc)?


Hello! The Rio is equipped with a 1.5L engine...@ 5800 RPM, HP=96...@ 4500 RPM, Torque=98 FT LBS.....Brake Specific Fuel Consumption (BSFC) is a ratio expressed by dividing Fuel Consumption by Power...An example would be...38 MPG divided by 96 HP would be a BSFC of .396...

I hope this is the information you required....Guru....saailer

Dec 18, 2010 | 2002 Kia Rio

1 Answer

What are the tranmission bolt torque specs on 92 ford ranger manual transmission, 4.0L engine


clutch housing to engine the torque is 28 ft lbs to 38 ft lbs.fly wheel torque is 59 ft lbs and torque pressure plate in sequence 15 ft lbs to 24 ft lbs.

Jan 02, 2010 | 1992 Ford Ranger

2 Answers

Sliding door fails to latch


There is no "switch". The Sliding Doors should be manual anytime you try to open or close them. If not: then there is problem in the electronic system or the physical/mechanical side where something is jamming the door from opening or closing.

Dec 31, 2009 | 2002 Chrysler Town & Country

1 Answer

Power sliding door stuck open 2002 Venture


first check the grounds make sure nothing is blocking its way from toys or anything kids can just put in there, and or make sure that there is no lock control other then that wire problems?? try to just do manual slide for now if you can.

Dec 08, 2009 | 2002 Chevrolet Venture Passanger

1 Answer

2002 Old Silhouette Driver Power Sliding Door will not open


Look in your owners manual there is a procedure to reset the door controls. If that dosen't work maybe the motor is burnt out, it's in the left rear access panel.

Mar 25, 2009 | 2002 Oldsmobile Silhouette

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...