Question about 2003 Ford Focus

Open Question

Where is the wiring harness for the brake light at mine was pulled out and broke need to be able to hook the wires back in the harness

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 32 Answers

SOURCE: Wiring a 2005 Taurus sedan for a trailer hitch.

White - Ground
Brown - Running Lights
Yellow - Left Turn, plus Stop
Green - Right Turn, plus Stop

Hope this helps!


Posted on Nov 13, 2008

Ad
  • 1779 Answers

SOURCE: Looking for a wiring diagram for a 2006 Ford Expedition

7way- black is 12volt (power), brown, running lights, yellow is left turn signal and stop light, green is right turn signal and stop light, white is ground, blue is brakes, and orange is aux power (can be back up lights, if trailer equipped w/ them). 6way is the same, minus orange wire. I have run into some variations to the above color codes (brown, yellow and green only-sometimes these 3 are different than stated, but only mixed as that group, as to what they control- example would be green is running lights, brown and yellow are turn signal and stop lights, the others should be as stated), if you have any trouble with things not working properly, it may be due to these variations, although the above are pretty standard. If you have an ohm meter you can check as you go (check for power at black wire- should be constant 12v, turn on turn signal and check for power-it will fluctuate from approx. 12 volts to 0 volts as the signal power pulses in the wire) hit the brakes, blue wire should show power, etc. Let me know if you need more help as you go.

Posted on Apr 11, 2009

ftw1952
  • 10319 Answers

SOURCE: tail light wiring connectors and wiring diagram

A test light checking each connector would be faster and easier to do. Maybe somebody may have a illustration for you but by far a simple test light is all you need with a helper turning on the different lights as you check them out and writing all your findings down

Posted on Jan 22, 2010

ZJLimited
  • 17970 Answers

SOURCE: need wiring diagram that will show me how to hook

Isn't excalty Ford model, but could helpfull...

zjlimited_178.jpg


I hope this helps.

Posted on Dec 06, 2010

sscullys
  • 984 Answers

SOURCE: I need the wiring diagram

This is the diagram for the fog lamps ( headlamp is a different cell ).
If you are trying to add them to the existing wiring, do not expect the headlamp switch to cab fuse panel wiring to be there ( that is usually what is missing when you can find the fog lamp connectors under the front of the truck ).

File Save as so you can magnify it with the JPEG viewer you use.

sscullys_90.jpg

Close up of switch
sscullys_91.jpg

Posted on Jan 28, 2011

Testimonial: "Thanks for the diagram, I'll have a pro install the needed wiring."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No brake lights anywhere


Test voltage on wires when use brake pedal, if you have voltage, could be some harnesses go to bad, or, somr broke wires.

Sep 04, 2012 | 2002 GMC Sierra 1500

1 Answer

No brake lights 2003 Ford Explorer but high mount works


maybe the one of the contacts on the bulb broke or the brake fuse

Aug 06, 2012 | 2003 Ford Explorer

2 Answers

My car lights and brake lights won't work all time


Sounds to me like a brake light switch is sticking or is faulty/bad wires. The switch is connected slightly above the pedal. And they are relatively cheap.

http://www.ipdusa.com/prodtype.asp?numRecordPosition=0&SEARCHWORDS=Brake+light+switch

Sep 17, 2011 | 1994 Volvo 940

1 Answer

When I hookup the brake lights come on.,,,I had the trailer come off the ball and pulled the cord out as well as the break away ,,, I replaced the plug on trailer as well as the receptal on truck. tried on...


When the trailer came off and pulled the light cord it stretched or broke wires inside the trailer harness. Start tracing back from the plug, paying careful attention to sharp bends and hold down points as well as connections. Remember that wire could pull apart inside the insulation without breaking it. It might be just as easy to replace the tailer harness. Hope this helps.

Jan 15, 2010 | Dodge Pickup Cars & Trucks

1 Answer

1995 gs 300 brakes light won't come on


I had the same prob w/ my 95 GS300. I also tried all the things u mentioned. My last thought was to follow the wiring from back to front (I'm an electrician). It ended up being a major slice thru the mass of wires that go thru the trunk into the passenger compartment on the passenger side. It looks like the wires must have rubbed up against a sharp weld between two body panels and broke that way. Anyway, mine broke in the channel underneath the doors between the back and front seats. 4 **** connectors and some heat shrink tubing and I was all set. Drove me crazy for a good two weekends.

Dec 15, 2009 | 1995 Lexus GS 300

1 Answer

Bought trailer harness for my trailer all four poles show 4 wires mine has five wires going to trailer lights turn on signals both light up like four ways also no brake lights. made sure all lights were...


try http://www.etrailer.com/faq-wiring.aspx. This should help. The 5th wire is a lockout for the brakes that hooks to your back up lights. So when you back up, the brakes won't engauge. Typically white is ground, yellow is left turn, green is right turn, and brown is running lights.

Sep 24, 2009 | 1998 Ford Explorer

2 Answers

I am looking for the wire under the rear of my 99 explorer to hook up the wiring harness for trailer or boat. HELP


From the factory there is an unused plug in the left brake light harness. You can get a tow light cable from Ford that's JUST for that, and its a 4 flat plug on the end. I 'found' mine in the compartment on the left where the jack is. Just peek in there with a light. It was still in the package. Otherwise call Ford, the thing plugs in and you route it down and there's a bracket to hold part of it under the bumper to an existing screw location.
-Cheers.

May 09, 2009 | 1999 Ford Explorer

1 Answer

Brake lights don't work?


Switch, wire harness problems, bulbs blown or wrong connectorposition fitted to bulb.
Connector bulb fitting you can check.
Wireharnes probleems:
Get 2nd person and a multimeter set for suitable 12 VDC range
Let him step on the break and you mesure between ground and +terminal of light bulb connector if there is 12 VDC. If all wiring gives Voltage when brakes kicked, harness ok. Then bulb/connector problem: correctly matched.
If no 12 VDC from wiring the left with harness or switch.
Small job, go to local dealer. Needs adjustment or broke.

May 06, 2009 | 2000 Mitsubishi Galant

3 Answers

Trailer light hook up problem


It sounds like your have may have your brake light and running lights crossed on your wiring harness to the trailer. Good luck and hope this help's

Apr 08, 2009 | 2004 GMC Envoy

Not finding what you are looking for?
2003 Ford Focus Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5516 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...