Question about 2001 Ford Windstar LX

1 Answer

Where is the idle air control valve wiring harness located on a 2001 ford windstar

Were is the idle air control wiring harness located

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 664 Answers

where is the idle air control valve wiring harness - idle-air-control-valve-wiring-harness-prnuo4xtyj5wakm52h23pt2g-5-0.jpg




idle-air-control-valve-wiring-harness-prnuo4xtyj5wakm52h23pt2g-5-9where is the idle air control valve wiring harness - idle-air-control-valve-wiring-harness-prnuo4xtyj5wakm52h23pt2g-5-14.jpgds/images/idle-air-control-valve-wiring-harness-prnuo4xtyj5wakm52h23pt2g-5-14.jpg this is the idle air control and the plug the wires may not be the same color the valve is located on the throttle body the photo's will make it easier to find it

Posted on Apr 06, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I just got my car scanned and a few codes pop up


Error Code: P0130
Fault:
Oxygen Sensor (O2S) 1, Bank 1 - Circuit Malfunction
Possible Cause:
Malfunction Indicator Lamp (MIL) Triggered on first occurrence.
-Wiring harness.
-Oxygen sensor (O2S).
-Engine control module (ECM).

Error Code: P0505
Fault:
Idle Speed Control (ISC) System - Malfunction
Possible Cause:
-Wiring harness.
-Idle speed control (ISC) actuator/Idle air control valve (IAC) valve.
-Throttle motor.
-Throttle valve tight/sticking.
-Engine control module (ECM).

Error Code: P0100
Fault Location:
-Mass Air Flow (MAF) Sensor/Volume Air Flow (VAF) Sensor - Circuit --Malfunction
Possible Cause:
-Wiring harness.
-Mass air flow (MAF) sensor.
-Volume air flow (VAF) sensor.
-Engine control module (ECM).

Error Code: P1491
Fault:
Exhaust Gas Recirculation (EGR) Valve Insufficient Lift
Possible Cause:
-Wiring harness.
-EGR Valve.
-ECM

Error Code:P1607
Fault:
-Engine Control Module (ECM)/Powertrain Control Module (PCM)

Error Code: P0966
Location:
-Pressure Control (PC) Solenoid B - Circuit Low
Possible Cause:
-Wiring short to earth.
-Pressure control (PC) solenoid.
-Engine control module (ECM)/Powertrain control module -(PCM)/Transmission control module (TCM) .


Apr 30, 2013 | 2004 Honda Civic

1 Answer

Stalls at a stop


The most common cause is a dirty throttle body or a faulty idle air control valve.
The computer controls idle speed by regulating the amount of air coming into the intake.
Could also be a vac leak.

Oct 02, 2012 | 2001 Ford Windstar

1 Answer

Van cuts in and out at stop sign or light runs fine when driving


If the idle speed is wandering, check the idle air control valve and the throttle body for dirt and varnish. The computer regulates the idle speed by the valve.

Jul 17, 2012 | 2001 Ford Windstar

1 Answer

Diagnostics test says idle air control underspeed error? how do i fix 1999 ford explorer


change the idle air control valve.

Idle Air Control (IAC) Valve OPERATION The Idle Air Control (IAC) valve controls the engine idle speed and dashpot functions. The valve is located on the side of the throttle body. This valve allows air, determined by the Powertrain Control Module (PCM) and controlled by a duty cycle signal, to bypass the throttle plate in order to maintain the proper idle speed. Fig. 1: Typical Idle Air Control (IAC) valve which is mounted to the throttle body - cutaway view shows air bypass direction 89684g16.gif
--- REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable. To remove the IAC valve, first disconnect the negative battery cable, then the IAC wire harness plug 89684p03.jpg
    Next, remove the two IAC valve attaching bolts . . . 89684p04.jpg
    . . . and pull the valve from the intake manifold 89684p05.jpg

  2. Disengage the wiring harness connector from the IAC valve.
  3. Remove the two retaining screws, then remove the IAC valve and discard the old gasket. To install: When installing the valve, always discard the old gasket and install it using a new one 89684p06.jpg

  4. Clean the IAC valve mounting surface on the throttle body of old gasket material.
  5. Using a new gasket, position the IAC valve on the throttle body. Install and tighten the retaining screws to 71-106 inch lbs. (8-12 Nm).
  6. Attach the wiring harness connector to the IAC valve.
  7. Connect the negative battery cable.
prev.gif next.gif

Oct 15, 2010 | 1999 Ford Explorer

1 Answer

Where is the idle control valve on 2001 windstar located?


near the throttle valve where the air intake hose connects tothe engine.
see picture below.

9ba4b28.jpg

Jul 29, 2010 | 2001 Ford Windstar

1 Answer

How to remove a idle air control valve is windstar 2001


Idle Air Control Valve The Idle Air Control (IAC) valve is located on the air intake plenum.


7515536.gif

Removal & Installation
Disconnect the battery ground cable.
Disconnect the Idle Air Control (IAC) electrical connector.
Remove the bolts and the IAC valve.
Discard the gasket.
To install:
Install a new gasket and position the IAC valve.
Torque the retaining bolts to 8 ft. lbs. (11 Nm).
Attach the electrical connector.
Reconnect the battery ground cable.

May 23, 2010 | 2001 Ford Windstar

1 Answer

How do I replace the idle control valve in a 1998 Ford Contour LX V6?


IDLE CONTROL VALVE: REMOVAL
1.Disconnect the vacuum hose from the exhaust gas recirculation valve. 8adde85.gif
2.Disconnect the idle air control valve electrical connector.e21fa1a.gif 3.Detach the idle air control valve wiring harness from the stud.
1caf5ed.gif
4.Remove the idle air control valve.
  • Remove the two nuts.

8176e69.gif I hope this is concise enough for you. Please give me thumbs up to thank me. By the way did I mention this info is FREE!!!

Feb 11, 2010 | Ford Contour Cars & Trucks

2 Answers

2001 Ford windstar stalling problems. After


have your idle speed sensor cleaned,also checkd the air flow sensor located in the air cleaner housing,you best bet is to have it scanned for PCM soft codes(codes that wont turn on the check engine light on)

Sep 08, 2009 | 2001 Ford Windstar

2 Answers

2001 ford windstar


Vacuum leak or idle air control valve.

May 16, 2009 | 2001 Ford Windstar

2 Answers

My ford windstar 2001 act little funny while stop Idle


I'm not sure Ford calls it this but I suspect the Idle Air Control. If you have a chain auto parts store in your area, most will scan your computer to see if error codes are stored; call them first to see if they do this at that location.

Jan 10, 2009 | 2001 Ford Windstar

Not finding what you are looking for?
2001 Ford Windstar LX Logo

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...