# How many 3 oz servings can i get out of 6 pounds of nacho's

Posted by on

• Level 3:

An expert who has achieved level 3 by getting 1000 points

Superstar:

An expert that got 20 achievements.

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

• Cars & Trucks Master

32 but what does it has to do with car anb truck categorie

Posted on Apr 05, 2015

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
goodluck!

Posted on Jan 02, 2017

×

my-video-file.mp4

×

## Related Questions:

### How many pounds is 18 gallons

How many pounds are in a gallon?
A gallon is a measure of volume equal to 128 fluid ounces (fl oz). One fluid ounce of water weighs one ounce (oz). So a gallon of water weighs 128 oz, or 8 pounds.
A gallon of other liquids will vary in weight depending on the density of the liquid.

Jun 03, 2017 | Cars & Trucks

### My ac system says it takes 2.63 pounds of r12 Freon. How many 12 oz or 14 oz cans will it take?

42.08 ounces (16 Oz in 1 lb) best to use appropriate gauges as overcharging will damage the system.

Jul 14, 2016 | 1992 Buick Skylark

### 1 lb 60z what is mean.pls answer me

What's the question?

Since one pound is sixteen ounces, 1 lb 60 oz is 4 lb 12 oz.

Aug 17, 2014 | Cars & Trucks

### How many pounds is 20 oz of freon

16 oz to a pound, so 20 oz are 1.25 pounds or 1 and quarter pounds.

Jul 14, 2014 | 1993 Cadillac DeVille

### How many pounds of freon does a 2006 trailblazer take?

If you have front and rear A/C 48 oz
if you have only front A/C 29 oz

Jul 21, 2011 | 2006 Chevrolet Trailblazer

### What is the R134A capacity on a 2003 Toyota Camry with a 4 cylinder engine? A repair shop billed me for 4 pounds.

It should be on a sticker under the hood

I will guess,maybe 24 oz ,less than 2 lbs

The most I have every seen since 1967
doing it, was 36 oz (2.25 lbs) back in the
1980's,since 1993 & the use of R134, the
systems have gotten smaller

Jun 13, 2011 | 2003 Toyota Camry

### How many pounds of r134 and how much oil ozs.

somewhere around 1.6 pounds (1lb.14ounces) of R134a if system is evacuated and 3 ounces of oil with new compressor.
keep pressure on the low side around 34-37psi & it should blow snow. Below are normal car AC pressure readings with 134A.
• Normal readings on high and low side with AC OFF (static pressure) – Depends on outside temperature, but normally is between 80-105 PSI
• Normal low side reading with AC on high speed and MAX & engine at 800-1000 RPM’s – Ranges from 25-35 PSI –
• Normal high side reading ranges from 200-350 PSI
Don’t assume that if adding little Freon is good that adding a lot is better! Overcharging just a little can decrease the performance of the system and possibly damage the compressor.
DIY recharge kit:
With the AC on the coldest setting, use a thermometer in a middle vent. Normal vent temperature readings will vary depending on the (ambient) outside temp. The vent temperature should range from around 42-55 degrees in my experience. If normal gauge readings are obtained and the vent air is cold – STOP don’t overcharge the system.
Thank you for using fixya and be safe.

Jul 19, 2010 | 1994 Chevrolet S-10 Blazer

### How many grams of r134a will it take as it has no plate with the info

Usually it will take 2 or 3 cans of 134a to charge a typical American car's or light truck's a/c system.

There are about 454 grams per lb. of matter and each can is about 12 oz. (not 16 oz. = 1 lb.).

3 cans would be 3 cans x 12 oz. = 36 oz. or about 2 lbs. 4 oz.

If you round down to 2 lbs., then the grams is about 454+454 which is about 900 grams rounded down.

You could find the grams per ounce and multiply by 36.

454 /16 = 28.375

and 28.375*36=1021 grams for 3 12 oz. cans of refrigerant.

Jul 04, 2010 | 2000 Ford Ranger SuperCab

### I want to disassemble a rear end of a "86" Suburban (to replace the spider gears)and I am not sure how to go about this can you help?

You will need the following....
Dial indicator
Gear marking compound and a clean brush
Calipers or a micrometer
Bearing pullers
Bearing press
Three foot long breaker bar or strong impact gun
Pinion nut socket
Ring gear bolt socket
Carrier cap bolt socket
Six point cross pin bolt wrench
Brake line wrench
Pry bars for removing the carrier case
24 oz ball pein hammer
48 oz sledge hammer
48 oz plastic dead blow hammer
Assorted brass punches
Punch for marking carrier caps
Oil drain pan
Foot pounds torque wrench
Inch pounds torque wrench
That should get it apart and back togather.
If you still want to do it...go to premium and i'll walk you through it...

May 04, 2009 | 1993 GMC Sierra K1500

## Open Questions:

#### Related Topics:

27 people viewed this question

Level 3 Expert

Level 3 Expert