Question about 2009 Jeep Grand Cherokee

1 Answer

ESP BAS LIGHT ON - 2009 Jeep Grand Cherokee

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 20,706 Answers

The operators guide says, get it service.
did you mean ABS (?)
if ABS comes on we scan it.
always
and check fuse (test them)

Posted on Apr 13, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
wracefans24
  • 1985 Answers

SOURCE: I am getting warning light code ESP BAS on my 2006

http://jeephorizons.com/phpbb/viewtopic.php?t=6836

Posted on Dec 06, 2009

  • 1 Answer

SOURCE: ESP/BAS

If the ESP light is on, the system is not functioning. have your dealer look at and replace your Brake Light Switch

Posted on Dec 17, 2009

  • 2926 Answers

SOURCE: my light says esp-bas. what

The system has detected a fault in the electronic stability program - brake assit system. You have an electrical connection at the rear wheels secured to the inside of the brake area and are viewable from under the vehicle. It is a small wire harness running to each wheel. Grab the connector and wiggle it around, and make sure they are tight. Due to the connector being mounted low to the ground, sometimes they become dirty or corroded, not making contact. Do this on both sides and see if the lights turn off.

Posted on Oct 15, 2010

  • 2926 Answers

SOURCE: 2006 Jeep Commander ESP/BAS and

Was the battery replaced and this occured afterward?

Posted on Apr 13, 2011

  • 2926 Answers

SOURCE: what does it mean when

ESP = electronic stabilitly program, BAS = brake assist system. There could be a number of issues causing these lights to come on. Loose sensor connector at one or more wheel locations. Build up of dirt and grim on the sensor or sensor wheel can also cause these lights to come on, These are the two easiest thoings you can do, otherwise, a service call will need to be made at your local Jeep dealer due to the complexity of this system.

Posted on Sep 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The esp bas light is on my 2009 dodge 1500 and it won't start


An Electronic Stability Program (ESP)/Brake Assist System (BAS) indicator is standard equipment on all instrument clusters. The ESP/BAS indicator is serviced as a unit with the instrument cluster.
The ESP/BAS indicator gives an indication to the vehicle operator when the Electronic Stability Program (ESP)/Brake Assist System (BAS) has been activated. This indicator is controlled by a transistor on the instrument cluster circuit board based upon cluster programming and electronic messages received by the cluster from the Controller Antilock Brake (CAB) and the Transmission Control Module (TCM) over the Controller Area Network (CAN) data bus.
The ESP/BAS indicator Light Emitting Diode (LED) is completely controlled by the instrument cluster logic circuit, and that logic will only allow this indicator to operate when the instrument cluster receives a battery current input on the fused ignition switch output (run-start) circuit. Therefore, the LED will always be OFF when the ignition switch is in any position except ON or START. The LED only illuminates when it is provided a path to ground by the instrument cluster transistor. The instrument cluster will turn ON the ESP/BAS indicator for the following reasons:
  1. Bulb Test- Each time the ignition switch is turned to the ON position the ESP/BAS indicator is illuminated for about four seconds as a bulb test.
  2. ESP/BAS Indicator Lamp-On Message- Each time the cluster receives an electronic ESP/BAS indicator lamp-ON message from the CAB indicating that the ESP/BAS system has been activated, the ESP/BAS indicator will be illuminated. The indicator remains illuminated until the cluster receives a lamp-OFF message from the CAB, or until the ignition switch is turned to the OFF position, whichever occurs first.
  3. ESP Full Off Textual Message- Each time the cluster receives an electronic ESP Full OFF indicator lamp-ON message from the CAB indicating that the ESP/BAS system has been manually disabled, an ESP OFF textual message will appear within the cluster odometer display. The ESP OFF textual message remains displayed until the cluster receives a lamp-OFF message from the CAB, or until the ignition switch is turned to the OFF position, whichever occurs first.
  4. Actuator Test- Each time the cluster is put through the actuator test, the ESP/BAS indicator will be turned ON, then OFF again during the bulb check portion of the test to confirm the functionality of the LED and the cluster control circuitry.
The CAB continually monitors the ESP/BAS circuits and sensors to decide whether the system is in good operating condition and the proper outputs to the components of the system. The CAB then sends the proper lamp-ON or lamp-OFF message to the Electro Mechanical Instrument Cluster (EMIC) (also known as the Cab Compartment Node/CCN).
For proper diagnosis of the ESP/BAS system, the CAB, the TCM, the EMIC, the CAN data bus or the electronic communication related to the ESP/BAS indicator operation a diagnostic scan tool is required. Refer to the appropriate diagnostic information.

Apr 11, 2016 | Dodge Cars & Trucks

1 Answer

The esp bas, abs, traction & brake light come on when I drive


take it to a mechanic! the drive train is failing

Jun 09, 2015 | 2008 Dodge Grand Caravan

1 Answer

Bas esp light come on 2010 dodge journey


Your Bas & Esp Light is on due to a failing or already failed Bas sensor & Esp Sensor, You can either do it yourself which can be very tricky if you are not confident with automobile repairs. The dealer should be able to do this at a reasonable price as it should take around an hour to do the repairs. If the problem keeps arising there could be a problem elsewhere that is connected to the same area & is shorting out.

I hope this helps.

May 11, 2015 | 2010 Dodge Journey

1 Answer

I have an 06 Dodge Magnum. ESP/BAS light


Whenever this warning or any other stays on in the dash it id indicating that the systems control module has detected a fault, it then disables the system as long as the light is on. You must now have the dealer hook up a special electronic diagnostic tool and "scan" the system for the fault code that is stored for the problem(s)

Sep 19, 2012 | 2006 Dodge Magnum

1 Answer

Esp/bas light came on - power features went out


sounds like your alternator is going out or have a short

Nov 03, 2009 | 2005 Chrysler 300

1 Answer

2005 magnum esp/bas and engine light on


you need to see what the eng lite for if there is a trans codes usually the pcm wont let the speed go over 40 stays in safe mode untill you fix the problem or change the sensor,for the esp you need to chage the esp sensor and recalibrate by the dealer

Jul 20, 2009 | 2005 Dodge Magnum

Not finding what you are looking for?
2009 Jeep Grand Cherokee Logo

170 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...