Question about Nissan Micra

1 Answer

Hi i cannot locate the revolution (crank shaft sensor) on my sons hot rod micra 1992 can you help me find where it is

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert that has over 500 points.

  • Nissan Expert
  • 242 Answers

Located in engine block at top of starter area pending engine size..All crank sensors are located in engine block area at the front or rear of engine...You will need a vehicle lift to safely inspect certain areas....It has a wiring plug connected to it...The sensor presses into block and is mounted with one bolt...

Posted on Apr 05, 2015


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the cam shaft sensor located in a 1992 ford explorer?

I list a crank sensor but no cam sensor for a 1992 with a 4.0 engine.

Jul 22, 2013 | Cars & Trucks

1 Answer

Wereis crank sensor located on my 1992 grand prix le

crank sensors are generally located above the crank(the main pulley at the passenger side of the engine compartment) outside of the motor. it is usually a black piece that just barely sits above the crank shaft.

Sep 23, 2012 | Cars & Trucks

1 Answer

I need help finding crank shaft position sencor on a 1992 licoln town car

The Crank position sensor is located on the drivers side front of the engine below the AC compressor and picks up its signal from the front crankshaft pulley trigger ring. In the picture below is a technican grasping the connection to the sensor and the sensor directly in front of the connector.


Apr 22, 2011 | Lincoln Town Car Cars & Trucks

1 Answer

Were is the crank shaft position sencor located on a 1992 licoln town car

The crankshaft sensor shoul or is located at front of engine bolted to the block . It senses the crank position so it is mounted where it can ,in close proximity of the pulley. Ned

Apr 22, 2011 | 1992 Lincoln Town Car

1 Answer

Change timming belt. where marks have to be set? 92 dodge colt

I lost you, stupid computer. Anyhow there are 8 different engines for the dodge colt in the early 1990's I can only assume its the 1.4L, 1.5L or 2.4L. The 1.4L & 1.5L the timing marks are exactly the same. The Cam points to 3:00 marks ther. The crank points almost straight up, slightly to the right, mark on engine cover. The 2.4L has 3 marks, The crank has an alignment mark at approximately 10:00, the cam sprocket points straight up at 12:00 and the idler pulley (to the right of crank shaft pulley) points approximately 11:00. They should all have a notch or mark when aligned. The short secondary belt, the crankshaft should be in the same location 10:00 and the balance shaft (to the left) should be at 9:00. This goes on after of course. Rotate engine 2 full revolutions and recheck marks before starting engine.

Feb 02, 2011 | 1992 Dodge Colt

1 Answer

1992 eagle talon - where is crank shaft sensor located

the crankshaft position sensor is located between the main pulley and oil pump pulley in the lower part of the timing belt.

Sep 17, 2010 | 1995 Eagle Talon

1 Answer

Where is the crank shaft sensor located on a 2003 kia sedona?

Hi, the crank sensor is located behind the timing belt cover. It is right above the crank shaft timing gear.

Sep 11, 2010 | 2003 Kia Sedona

1 Answer

Were is the cam shaft senor and the crank shaft senor located

this car does not have a camshaft sensor the distributor pick up coil acts as a cam sensor here is crank sensor info the crank sensor is located in front of engine just behind the crankshaft pulley using ohmmeter check resistance between terminals on sensor replace is not within specs cold 1630-2740 ohms hot 2065-3225 ohms if this is not the problem please reply to your post ill monitor it. hope this helps

Jul 26, 2010 | 1996 Toyota Corolla

1 Answer

Have problem 1992 sentra take to long to start when hot or left along for long time

hi there sounds like you have a problem with the crank shaft sensor

Mar 03, 2010 | 1992 Nissan Sentra 4 Door

1 Answer

Has trouble turing over at start

Looks like an easy job.

Crankshaft Position Sensor: Description and Operation
Component Description
The crankshaft position sensor (POS) is located on the cylinder block rear housing facing the gear teeth (cogs) of the signal plate at the end of the
crankshaft. It detects the fluctuation of the engine revolution.
The sensor consists of a permanent magnet and Hall IC. When the engine is running, the high and low parts of the teeth cause the gap with the sensor
The changing gap causes the magnetic field near the sensor to change.
Due to the changing magnetic field, the voltage from the sensor changes.
The ECM receives the voltage signal and detects the fluctuation of the engine revolution.

Sep 02, 2009 | 2002 Nissan Altima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

78267 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides