Question about 2000 Mazda MX-5 Miata

1 Answer

WHAT WOULD BE THE TORQUE ON NUTS FOR FRONT WHEEL DRIVE

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Mazda Expert
  • 242 Answers

52 to 62

Posted on Apr 05, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the torque specs for a front wheel bearing?


if its not a drive axle and only has a castle nut with a cotter pin , then regrease the wheel bearings and run nut all the way in to its hand wrench tight (not impact gun), turn wheel one or two full turns to seat it , then back castle nut off two spaces and install cotter pin , this s\is std way to set proper spacing on wheel bearings

if its a drive axle consult your cars model and make and year torque specs book

Mar 29, 2016 | Cars & Trucks

1 Answer

Front wheel bearing specs on Toyota t100 1995 4 wheel drive


You tighten the nut until the wheel starts getting hard to turn, then back off the nut 1/4 turn.

Jun 18, 2015 | Toyota T100 Cars & Trucks

1 Answer

Front axle 2002 highlander


to remove front axle.to loosen front axle nut leave vechicle weight on wheel then just loosen front axle nut because axle nut torque at 217 ft lbs torquehard to loose axle nut with vechicle weight off wheel.okay. you need a 1/2 breaker bar and axle socket to loosen axle nut dont use 12 points sockets need go auto parts store buy right socket for axle nut.okay when you loosen front axle nut you need safely raise support vechicle. need to remove wheels remove fender apron seal remove transaxle fluid remove transfercase oil if you have 4WD.remove hub nut remove stabilizer bar link remove speed sensor remove tie rod end remove lower arm from the ball joint then slide the halfshaft from the hub then carefully pry the shaft from the transaxle.then install new front axle push in make sure front axle snap ring on front axle snap in place inside transmission just pull a little on front axle make its in place. when all done tighten front axle much as you can then when done putting every thing back in place.lower vechicle need torque front axle nut to 217 ft lbs.

Jan 12, 2013 | 2002 Toyota Highlander

2 Answers

I need the torque specs for a 6 cyl 2004 Dodge Dakota 2 wheel drive- front wheel hub. In inch-lbs if possible.


Spindle nut. Tighten the nut to 185 ft. lbs. (251 Nm). Inch pounds is not an option, this critical torque spec is FT lbs.

Apr 26, 2011 | 2004 Dodge Dakota

1 Answer

TORQUE SETTING ON FRONT WHEEL BEARING NUT ON 2006 PONTIAC TORRENT


Hello, here is the torque spec for front hub bearing
Strut to Steering Knuckle Bolt and Nut
180 N·m
133 lb ft
Tie Rod Retention Nut
50 N·m
37 lb ft
Wheel Bearing/Hub Mounting Bolt
130 N·m
96 lb ft
Wheel Drive Shaft Spindle Nut
205 N·m
157 lb ft

Nov 07, 2010 | 2006 Pontiac Torrent

1 Answer

REMOVAL OF FRONT WHEEL BEARINGS


Front (4 Wheel Drive) To Remove:
  1. Raise and support the vehicle
  2. Remove or disconnect the following:
    • Tire and wheel assembly
    • Rotor (See: Disc Brake Rotor)
    • Wheel speed sensor and brake hose mounting bracket bolt from the steering knuckle
    • Electrical connection for the wheel speed sensor
    • Front drive halfshaft assembly (See: Halfshaft)
    • Hub and bearing assembly mounting bolts 4WD front hub 9308kg35.gif

    • Hub and bearing assembly
To Install:
  1. Clean all corrosion or contaminates from the steering knuckle bore and the hub and bearing assembly
  2. Lubricate the steering knuckle bore with wheel bearing grease or the equivalent
  3. Install or connect the following:
    • Hub and bearing assembly
    • Hub and bearing assembly mounting bolts and tighten the hub to knuckle bolts; Torque to: 133 ft. lbs. (180 Nm)
    • Front drive halfshaft assembly (See: Halfshaft)
    • Electrical connection for the wheel speed sensor
    • Wheel speed sensor and brake hose mounting bracket bolt to the steering knuckle and tighten the bolt; Torque to: 106 inch. lbs. (12 Nm)
    • Rotor (See: Disc Brake Rotor
    • Tire and wheel assembly
    Wheel lug nut tightening sequence gm_trk_sub15_wheel_lug_nut_tight_seq.gif

  4. Torque the lug nuts to specification
  5. Test drive the vehicle to confirm the repairs
prev.gif next.gif

Aug 03, 2010 | 2001 Chevrolet Silverado 1500

1 Answer

Front bearing nut torque specification rear wheel drive?


front bearing wheel nut holding axle on? 115 foot pounds and hammer in or crimp the nut after tightening. ^ like shape into slot of axle this locks the axle. for the wheel bearing for rear wheel drive the nut should be tightened by hand till tight 15 foot pounds then backed off 1/4 turn, be sure there is plenty of grees in the bearing cup before tighting nut be sure to line up slot for key with rotor on the rotor should turn free and should not have any slop in it, put the wheel on it and put the nuts on and try wiggleing the wheel back and forth if any movement readuast nut. If it is to tight it will over heat outter wheel bearing, also be sure there is greese in inner wheel bearing.

Jul 14, 2010 | 2000 Mercury Grand Marquis

1 Answer

Can I replace wheel bearings on my 2 wheel drive 2001 BLAZER


In addition to the great answer above, it is extreamly improtant to torque the front hub nut to the proper torque. If you under or over torque the nut which puts pressure on the bearing, you will be changing it again in a very short time. Refer to a shop manual, or go to the local auto parts store and look at a chiltons manual for reference torque value.

May 25, 2009 | 2001 Chevrolet Blazer

Not finding what you are looking for?
2000 Mazda MX-5 Miata Logo

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8211 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...