Question about Ford Bantam

1 Answer

Hi ?? lve got 2005 ford bantam rocam engine problem is it l hit at pot hole than car just cut of l tried to start but it not starting

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 154 Answers

You should probably look for damage under the car - probably hit someething underneath like - pinching a fuel line - or denting the fuel tank - a good jarr/bump can knock things loose - look closely at the fuel lines
Let me know what you find out

Posted on Apr 05, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
tbirdfan1
  • 3051 Answers

SOURCE: I hit a pot hole, car started acting funny. I

Hello there and welcome to fixya
If this vehical has a fuel cut off switch whick most modern day vehicals have it may have been set off by the shock of the pot hole so i would first check your users manual to see if you have one and if so check on how to reset it if this checks out ok then check the all of the fuses to ensure that you didnt blow a fuse this is very common ok then check all of the wiring going from the battery to the started to see if any of them are loose and the ground from the battery ok.
Please keep me posted on how this is going so i can continue to help
Best regards Mike

Posted on Mar 15, 2012

emissionwiz
  • 76846 Answers

SOURCE: diagram how to replace fan belt on ford bantam rocam engine 1.6

Here is the diagram I show.
9_28_2012_8_40_43_pm.jpg

Posted on Sep 28, 2012

czaa
  • 4536 Answers

SOURCE: I got a 13i ford bantam rocam engine the vichle

cud be transmisssion issues--or bad residual fuel pressure-thats held by the injectors--do a scan for any codes-present or historical

Posted on Dec 16, 2014

  • 45373 Answers

SOURCE: Will a 1.6 Ford Bantam Rocam motor fit onto a 1.3 Ford Bantam Rocam gearbox, and is the engine mounting brackets the same

same engine, same year only difference is bore size so there is every chance that it will fit.

Posted on Jan 26, 2015

  • 3519 Answers

SOURCE: I have a ford bantam rocam,da aor filter box had a hole in it a oil was leakin frem it,I seal it up,wud da smpke go bck in da engine

Hi Again Lawrence:
From what I can see, you are dealing with the PCV tube. It may be that the PCV valve is gummed up. Make sure that it is clean and functioning properly. Also , check that all rubber tubing and grommets are in good condition.

Posted on Mar 20, 2015

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the speed sensor situated on a Ford Bantam 1.6 rocam


It is plugged into the transmission where the speedo cable would go in older cars.

Jun 22, 2016 | 2008 Ford Bantam 1.6i

2 Answers

How do I fix a Bantam that wont start?


no idea but change the mass air flow sensor on or in the inlet manifold

Jan 03, 2016 | 2005 Ford Bantam 1.3i

1 Answer

My bantam refuse to start I don't heart the fuel pump click on and off , can you tell me where the fuse or fuel relay situated.


Spray quick start down the intake, if it starts you have a fuel supply problem. If that is the issue check if your Ford does not have one of those cut off switches ... some have those that would kick off if you hit a curb or big enough pot hole. If not put a tester on the wires to the pump and see if you get 12Volts there when you turn on the key. If yes ... bad pump ... if no ..check fuel pump relay ... switch with a different relay ... sometimes they have the same relay for 3 or 4 other items on the car like horn or lights and so on. If still no you may have one of those cars that when the crank or cam sensor goes bad it turns off power to the fuel pump for safety issues. Hope this helps. Good luck

Jun 12, 2015 | 2005 Ford Bantam 1.3i

2 Answers

Hi l've checked the fuel switch as u advice but still my car is not starting l also checked the fuel system plz help me 2005 ford bantam rocam engine l hit the pot hole then car just cut off and


Try spraying a shot of wd40 into a couple of the spark plug holes, reinstall plugs and wires and try again. The wd40 will allow the vehicle to start if there is spark. Check your coil pack connections.
Was anything torn off when you hit the pot hole?

Can you check if there is spark since you verified fuel ? please let me know. A car needs fuel (wd40) and spark to run.
spiescic@cogeco.ca

Apr 05, 2015 | Ford Bantam Cars & Trucks

1 Answer

I got a 13i ford bantam rocam engine the vichle start and idle but cuts out as soon as I accelerate


cud be transmisssion issues--or bad residual fuel pressure-thats held by the injectors--do a scan for any codes-present or historical

Dec 16, 2014 | Cars & Trucks

1 Answer

Ford 1 3 rocam engine


bantam?
most cars, MPI injection the injector form a sandwich.
between the fuel rail, and the intake front tunnel tubes.
so remove the rail,
step s
remove battery neg lug, so some, odd person dont try to start car.
depressurize the fuel system per FSM.
then remove injector conn plugs.
the unbolt rail. bingo.

the FSM covers this, ask ford parts counter for this book.

The Ford Bantam is a coupe utility vehicle ("bakkie", "pickup", or "ute") produced by the Ford Motor Company in South Africa. It spanned into three different models and was produced in South Africa for the local market.

be safe.

Jul 09, 2014 | 2005 Ford Bantam 1.6i

1 Answer

Ford bantam does not start


Check the reset switch near yo icu. reset it if off

Mar 16, 2013 | 2005 Ford Bantam 1.3i

2 Answers

Guys I've got a problem with a ford bantam 1.6i 2003 model rocam engine, its overheating even though the cylinder head was skim but it still overheating. please assist!


Check what head gasket was used . I suspect that an after market gasket was used. If that is the case there will be holes in the block and head thet have no matching holes in the gasket thereby causing the problem

Jan 07, 2013 | 2006 Ford Bantam 1.6i

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...