Question about Cars & Trucks

1 Answer

What do u call the part that's missing what covers the throttle body

Posted by Anonymous on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 954 Answers

The air duct that connects the air cleaner to the throttle body.

Posted on Apr 05, 2015


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

00Linc ls v8 hose connected to side of throttle body from valve cover disconnected at throttle body noticed oil what's wrong

That will be your PCV hose. If there is no valve there it is missing.
Engine will not run properly due to vacuum leak, and crankcase will be venting through valve cover, hence the oil.

Dec 06, 2015 | Cars & Trucks

1 Answer

Revs up while idling

If you didn't correctly reinstall the PCV hose from the black box at the throttle body back on to the valve cover, you might have a vacuum leak causing your high idle. I'd check that first. That is a common mistake to miss that rubber hose. It's hidden underneath the black box at the front of the valve cover. If it is loose, just loosen up the boot at the throttle body, and the two bolts on the right side of the black box above the valve cover. Reposition the 90 rubber hose back on to the valve cover and recheck it. A hissing noise with the engine running is a good indication that the engine has a vacuum leak somewhere- usually a rubber hose disconnected from the intake manifold or throttle body.

Oct 18, 2013 | Chevrolet TrailBlazer Cars & Trucks

1 Answer

How do i change the throttle body module

follow this steps and fix it. God bless you
Make sure the engine and all components are completely cool. Disconnect the battery ground. Then isolate it to avoid accidental contact with the terminal while installing the throttle body.

  • 2 Remove the engine cover fasteners and take off the engine cover. Take out the air intake duct and then take the cover off the air filter. Disengage the electrical connector from the throttle control assembly.
  • 3 Label the hoses on the throttle body to their respective fittings. Disconnect all the hoses. Take the accelerator cable from the throttle body on vehicles with the 2.0L engine.
  • 4 Remove the throttle body fasteners and lift the throttle body off the manifold. Drape a clean shop cloth over the opening to prevent debris from falling into the engine.
  • 5 Pull the gasket and dispose of it. Clean the mating surfaces of all traces of dirt, old gasket material and carbon deposits.
  • Oct 18, 2012 | Cars & Trucks

    1 Answer

    Nissan March/Micra missing when warms up. Have replaced all coils, was better for a few days now missing again.

    For this model I personally have some experience. If your engine has the throttle body like the carburator ,follow the steps I recommend. If you have a good knowledge on mechanics,remove the throttle body carefully,strip it piece by piece and everything in order just for you to be easy on installing. on the side of the body there is a square aluminium cover where is the electronic card which is controlling all the throttle system.Using a magnifying lens you check the three pins which are soldered to the sensor of three pins. Because the manufacturer is using not a very good quality of solder get very tiny cracked where can not be seen without any magnifying lens . what you have to do remove the old solder and re do it,very carefully not to damage anything. close the cover with a good silicon sealant. Then remove the choke which is on the side and their you will find lots of carbon and needs good cleaning ,renew the O ring and seal everything very carefully.The Throttle Position Sensor which is on the side,mark it before remove so as when you install to be in same position. Needless to say that you have also to clean the throttle body and get a new gasket and re install. Surely will work better. If you need any further advice please ask. Good Luck.

    Sep 11, 2012 | 2005 Nissan Micra Visia

    1 Answer

    Catalytic converter ses code.

    Possibly used rags to cover exhaust flanges, Throttle body etc... Missed a rag in exhaust which on start up would block the front of the cat. Especially if polyester type rag or similar will melt over input of cat causeing it to block up.

    Jul 14, 2012 | Chevrolet Silverado 1500 Cars & Trucks

    2 Answers

    1990 chevy blazer 350 ci throttle body fuel injected . the motor is flooding out u can see the injectors keep dumping fuel into the throttle body

    Sounds like you have an injector leaking. Have someone just cycle the key on and off to run the fuel pump but don't crank the engine. If you see fuel dripping from the injectors, unbolt the injector cover on the throttle body, remove the injectors and replace the orings around the injectors.

    Jul 22, 2010 | 1991 Chevrolet C1500

    1 Answer

    Dear Sir, I have a 1997 Jeep Cherokee Sport, 6 cylinder 4.0 liter. I recently tried cleaning my throttle body with carb cleaner while the vehicle was running. After spraying a half can of cleaner in the...

    do a compression check on the engine, and replace the bad sensor, i take the throttle body off to clean it and some sensors are touchy about cleaner, i fear maybe something got on the egr valve pintle

    May 26, 2010 | 1997 Jeep Cherokee

    2 Answers

    2003 ford f150 misses at idle starts fine runs fine new fuel filter new o2sensor

    One thing to take a look at is the vacuum elbow on the back of the throttle body.

    Remove the plastic throttle body cover, and check the vacuum line.

    Ignore the IAC notation, this is the only picture I have handy, showing the vac line just above the IAC.


    Dec 19, 2009 | 2004 Ford F150

    1 Answer

    1991 S10 2.5L throttle body idles to fast

    A vehicle that old will suffer from brittle and cracked vacuum lines. I would say there is a bad, or several bad lines leaking away vacuum from the intake manifold. Don't forget to check the hose going to the PCV on the valve cover. A vacuum leak will also cause the engine to stumble and miss intermittently when idling.

    Jun 26, 2009 | 1991 Chevrolet S-10

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    16 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts


    Level 3 Expert

    76846 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides