Question about 2004 Ford Freestar

Open Question

Were to look for transmission sensors on a 2004 ford freestar limited edition

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2004 ford freestar drivebelt

All you need is a 13mm boxed end wrench. The tensioner pulley is the one all the way on the bottom towards the rear of the van. You can reach it under the van. Slide under the van in front of the passenger front tire and you will wee the pulley. Put the wrench on the bolt and pull towards you to release the tension on the belt.

Posted on Feb 08, 2009

Ad
  • 1 Answer

SOURCE: ford freestar 2004 the TRAC OFF message comes

I had the same problem and apparently fixed it by mistake. I replaced the cruise control deactivation switch under the master cylinder, hoping the cruise would be fixed. Some how with that the "trac off" light went out and gave me the ability to turn it on/off from the button again. The part was $30 from the local dealer and easy to replace. Before you run out to replace the switch check the connections on the old one. It plugs in upside down which may accumulate water from puddles and things causing connection issues ( a known problem ).

Posted on Sep 23, 2009

  • 4369 Answers

SOURCE: 2004 Ford Freestar with P0340 Code. What is it

camshaft position sensor

Posted on Jan 16, 2010

  • 1 Answer

SOURCE: 2004 ford freestar rear hatch latch broken

have you fixed yours yet? mine started doing this last year

Posted on Mar 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need the code PO722 for a 2006 ford freestar 3.9


Hope, code PO722 Output Speed Sensor No Signal.
Possible trigger for code,
  • Defective Output Speed Sensor
  • Defective Shift Solenoids
  • Defective Engine Coolant Temperature Sensor
  • Defective Valve Body
  • Dirty transmission fluid that restricts the hydraulic passages
  • Defective Output Speed Sensor wiring or connector
P0722 Ford Output Speed Sensor No Signal
http://www.autozone.com/repairguides/Ford-Freestar-Monterey-2004-2006/Diagnostic-Trouble-Codes/4-2L-V6-VIN-2-Auto-5/_/P-0996b43f802e829c

Aug 27, 2016 | 2006 Ford Freestar

1 Answer

Ford freestar


Suddenly the fans stayed on and the weather does not work, it's hot or cold

My freestar 2006 , help me please .
thanks

josue

Sep 24, 2013 | 2004 Ford Freestar

1 Answer

2004 ford freestar van idles rough


For rough idle and error code issues on your ford freestar.Click the link below:----
http://howtobyme.blogspot.in/2012/01/2004-ford-freestar-van-idles-rough.html
--------This will help.Thanks.

Jan 31, 2012 | 2004 Ford Freestar

1 Answer

Remote control is not working at all. Checked the remote and replaced battery. Also back sensors not working. only a click while engaging reverse gear. Ford Freestar 2004 limited 4.2 L Is there any...


Hello, I want to try to help you on this problem. The Limited models of the product line have extra "Bells and Whistles" added to the normal dash functions. You have a dash display Computer which shows a Menu for the extra features. On this Menu, you can set the "Back-up" alert system to be On or Off.

Sometimes when an Oil Change is done, the Technicians have to Reset the Oil Change counter. They use this Menu and could easily have changed the settings for the Back-up and the Remote control functions. You need to get into the Menu and see if this is the case.

For added measure if the Menu does not help, look under the Drivers' dash at switch on the Brake pedal(gets bumped), the switch for the Transmission selector is more difficult to see. Test to see If the Back-up sensors work in Neutral and not Reverse, the shift cable will need to be adjusted. That's about all you can do yourself.

Sometimes the "Brain" in the door handle will die and you will need a new part. I hope my solution is very helpful to you.

Sep 04, 2011 | 2004 Ford Freestar

1 Answer

2004 ford freestar speed sensor is bad I need to know where it is located. also is it of to drive with a bad sensor?


it is usually on the side of the transmission, we call it a transducer here in australia
its ok to drive the car with the speedo out but you will have to watch your speed

Jul 04, 2010 | 2004 Ford Freestar

1 Answer

Transmission light comes on at highway speeds


CHECK TRANSMISSION FLUID LEVEL FIRST.IF OKAY.YOU COULD HAVE SPEED SENSOR PROBLEM OR TORQUE NOT LOCKING UP TO OVER DRIVE.HAVE TRANSMISSION SHOP OR DEALERSHIP CHECK IT OUT.

Apr 02, 2010 | 2004 Ford Freestar

1 Answer

Sensor location


here is where it is on 2003 Windstar. I don't have Freestar.

4841b35.gif

Mar 09, 2009 | 2004 Ford Freestar

Not finding what you are looking for?
2004 Ford Freestar Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5572 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...