Question about 2006 Chrysler 300

1 Answer

How to reset anti theft system on 2006 Chrysler 300. No sound when starting engine. Engine doesnt crank.

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 3,218 Answers

This may be accompanied with the power door locks not working also. You may be able to reset it by pulling the fuses in the underhood fuse relay center. The fuse or fuses that may reset the system are sitting in special holders in the relay center that have little clips on the side.They will look different from the other fuses as they have their own little holders. Pull them up and reseat them. Hope this helps

Posted on Apr 05, 2015

Testimonial: "So that didnt work either. we think maybe it might be the ignition."

  • 1 more comment 
  • Anonymous Apr 05, 2015

    Do you know what fuses specifically seeing that there are a lot. I have already tried jump starting car, disconnected and reconnected battery, (this helped my buttons on keys to work again) and . Also bought new remote batteries... so lost right now and really dont wanna take to the shop. Please help.

  • paulmacintyre
    paulmacintyre Apr 05, 2015

    There should be one labeled IOD and may be sitting in a red holder in the underhood relay box. Look in your owners manual for the location and remove itfor 10 sec and reinstall it. I hope this helps

  • paulmacintyre
    paulmacintyre Apr 05, 2015

    Have you tried your spare key? Try putting the gearshift in neutral and turning the key. If these tips don't help you may have a problem with any of the following... Starter motor.. Starter relay..Pcm..Bcm..Wcm..wiring. You will need to have diagnostics run to determine and isolate the issye. Wish I could be of more help

×

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Car won't start, but engine turns over.

my car won't start, the anti theft system is on,

Posted on Mar 28, 2010

  • 2 Answers

SOURCE: How do I reset the anti- theft computer in a 1999

did you try to remove both battery cables for about 10 min or so ?? that may reset the comp and clear the problem

Posted on Aug 07, 2010

nicole99wu
  • 1049 Answers

SOURCE: Anti Theft System

Tool Digimaster 3 may satisfy your need

Posted on Aug 02, 2012

  • 512 Answers

SOURCE: 2006 chevy express van reset anti theft system?

there may also be a "key chip" that goes under the dash, I have seen those fall out and keep the car from starting (looks kind of like a wide USB fob such as this:
25356510-sxneijxydcsro1nodh24pjva-5-0.jpg

Posted on Jan 06, 2015

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW DO YOU RESET ANTI THEFT SYSTEM ON 2006 CHRYSLER 300


It will need reprogrammed with a scan tool

Dec 22, 2014 | 2006 Chrysler 300

1 Answer

2006 CHRYSLER VAN PUT KEY IN TO CRANK AND HORN BLOWS AND WILL NOT CRANK


This can be a tough one but in all probability the problem will be in your anti theft system. Try this, have someone boost the battery. The engine should turn over and the horn will sound. When it starts use your key fob to lock and unlock the doors. That should reset your alarm system. In all probability your battery needs replacing. Try that. Good luck.

Jun 15, 2014 | 2006 Chrysler Town & Country

1 Answer

My 2006 dodge stratus wont start


If the engine will not crank over with the starter then have the battery and starter tested first and then go from there. If the theft system is the problem you will have a warning light on in the dash or a message on alerting you to the problem in the anti theft system.

Aug 23, 2012 | 2006 Dodge Stratus

2 Answers

The car wont start, the brake pedal is locked like the anti-theft is active, the anti theft light is flashing when the keys are in the ignition. when i try to turn it on it doesnt turn over, just makes...


TRY REPROGRAM KEY .PUT KEY IN IGNITION SWITCH TURN IGNITION SWITCH ON POSITION 20 SECONDS DONT START ENGINE WAIT 20 SECONDS TURN OFF SWITCH THEN TURN SWITCH BACK ON 20 SECONDS WATCH THE THEFT SECURITY LIGHT BLINKING.WHEN THEFT STOP BLINKING VECHICLE WILL CRANK.IF LIGHT STILL BLINKING.TRY FEW MORE TIMES KEY IN SWITCH ON POSITION FOR 20 SECONDS.MAKE SURE YOU HAVE THE CORRECT CAR KEYS IN SWITCH IF NOT WRONG SET OF CAR KEYS WILL SET OFF THEFT SECURITY SYSTEM.IF KEY RESETTING TRICK DONT WORK.CHECK BATTERY POWER MAKE SURE YOUR BATTERY HAS 12.5 VOLTS AND CHECK SECURITY THEFT FUSE.IF ALL LOOKS GOOD YOUR SECURITY HAS TO BE CHECKED OUT AT THE DEALERSHIP.

Oct 08, 2010 | 2006 Ford Fusion

3 Answers

New battery but still won't start.


are u certain you have a anti theft system, it was an option in this year, let me know, if u do locking and unlocking the passenger door with the key is supposed to disarm it according the owners manual I have, if u do have the system and it will not disarm then there is a problem in the control module, also u need to check for fault codes in the engine electreonics, go to the link belwo for instructions, Jeep uses the same test as all products from Chrysler Corp.

http://check-engine-light-codes.blogspot.com/2006/04/chrysler-1985-95-obd1-code-self.html

Apr 26, 2010 | 1995 Jeep Grand Cherokee

1 Answer

1989 300e. The anti theft alarm went off while driving the car now the engine won't start. We shut the car off and locked and unlucked the doors several times. The alarm reset and we began driving again. A...


This is the problem due to your anti theft alarm system. You have not mentioned which brand of anti-theft alarm system you have? Anyhow, most of the systems have a reset switch inside the kit, open the kit and on the main board, u will find the reset button, press that and hold for 5 sec, the system will be reset. Otherwise, there are 2 or 3 fuses with the wiring of kit, remove those fuses and ur engine will wake up but the anti-theft system wont work then, hope this will solve the problem

Sep 19, 2009 | 1989 Mercedes-Benz 300-Class

3 Answers

RESETTING CHECK ENGINE LIGHT


I can only assume you have had the code extracted and fixed the problem and looking to do a reset only. If you have not fixed the problem the reset wont do any good. That being said, in most all chrysler vehicles, the check engine light can be reset by disconnecting the negative battery cable for at least 15 seconds. However on OBD II (usually 97 and newer) models the light can only be reset with the use of a scan tool. CAUTION : If the stereo in your vehicle is equipped with an anti-theft system, make sure you have the correct activation code before disconnecting the battery cable.

Sep 26, 2008 | 2006 Chrysler 300

Not finding what you are looking for?
2006 Chrysler 300 Logo

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...