Question about 2003 Cadillac CTS

1 Answer

Cadillac cts 2003 3.2l engine the timing belt jumped time i replaced the set it back on the timing marks an it didn't start i a code po 341 so replaced the camshaft position sensor didn't start

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

The same thing happened to my 03 CTS. The camshaft position sensor code is often thrown for a variety of reasons. In my case somehow the ECM went when the timing belt jumped (after the serpentine belt broke). It was a bear to diagnose but after installing a rebuilt ECM it runs great. (Don't make the mistake I made: the cylinder head gaskets will fit nicely on either side but if not placed on the correct sides you'll block the single oil port which provides engine oil to the head)

Posted on Apr 06, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Ajkill
  • 2035 Answers

SOURCE: Location of camshaft position sensor on a 2001 Hyundai Elantra wL

The camshaft position sensor is located on the engine near the timing belt cover and under the upper radiator hose.

Posted on Dec 26, 2008

  • 55 Answers

SOURCE: replacing bad camshaft position sensor

  1. Disconnect battery ground cable.
  2. Remove water pump pulley attaching bolts, then the serpentine belt and water pump pulley.
  3. Disconnect sensor wiring connector and remove sensor retaining bolt.
  4. Twist and pull sensor to remove.
Reverse procedure to install and prior to installing new sensor, lubricate sensor O-ring.

It is located under the water pump. Make sure when you remove the sensor that you rotate the crank shaft and look in the hole to make sure the pick up magnet is still in there. Sometimes they come loose and cause a no start or long crank. You will need to have the code cleared still.

Posted on May 06, 2009

csmock132
  • 4669 Answers

SOURCE: ERROR CODE 0340 AFTER TIMING BELT REPLACEMENT

Well either coincidence that the cam sensor went bad, you forgot to plug in the cam sensor, Or you have the cam that the sensor reads off of 1 tooth off. Check to see if its plugged in if yes remove the upper timing cover and see if everything lines up.

Posted on Jun 08, 2009

  • 51 Answers

SOURCE: 2003 Dodge Neon: P0016 (already replaced sensors, belt, tensioner

the computer may need to be reflashed. if it is running then it is not a bad sensor. either of those being bad would cause it not to run.

Posted on Aug 08, 2009

  • 1757 Answers

SOURCE: isuzu trooper 2002 RLV engine. camshaft timing

Sorry for the severe delay.
I am personally going back to answer your unanswered question.
I do not know if you still need the answer, but I am going to answer it in case you still do.

Click on the following direct Link. It has the Timing Belt Diagrams and Photos with Marks for the Camshaft and Crankshaft that you will need. It also has numerous other helpful diagrams, instructions and photo's for use.

Again my apologies...
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!


http://www.2carpros.com/car_repair_information/year/2002/make/isuzu/model/trooper/2002_isuzu_trooper_timing_belt_diagram_marks.htm

Posted on Mar 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Diagram for a 2003 Cadillac cts serpentine belt


Below is the master help link provided to go through belt routing diagram:---Timing belt, drive belt, serpentine belt, accessory belt, fan belt, engine belt routing diagrams for all types of car models?
Click the link below: ----

http://carbeltrouting.blogspot.in/2012/02/timing-beltdrive-beltserpentine.html
----------This will help. Thanks.

Jan 30, 2012 | 2003 Cadillac CTS

1 Answer

Need timeing marks for 2003 cadillac cts timing belt


you have to go on line look up autodata online manual or look for cts online repair manual you have to pay small fee for month use or you can use on line repair manual for year if you pay for the year fee.

Nov 22, 2011 | 2003 Cadillac CTS

2 Answers

I need to know how to set the timing belt on my 2003 cadillac cts 3.2L.engine.any diagrams will help a lot thanks


Timing Belt & Sprockets Removal & Installation 3.2L Engine To Remove:
TDC compression stroke timing marks gm_car_cad_cts_04_tmg_mrks_tdc_comp.gif

  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    • Timing belt cover
    • Crankshaft damper
  3. Rotate the crankshaft in the engine rotation direction, clockwise using the J 42098 or other suitable tool until the # 1 cylinder is at Top Dead Center (TDC) on the compression stroke. The reference marks on the camshaft gears should be aligned with the corresponding notches on the rear timing belt cover, as well as the mark on the crankshaft sprocket and oil pump housing. Timing marks 60 degrees from TDC gm_car_cad_cts_04_tmg_mrks_60_frm_tdc_comp.gif

  4. Rotate the crankshaft counter clockwise using the J 42098 or other suitable tool until 60 degrees Before Top Dead Center (BTDC). The 60 degrees BTDC point can be identified by the index mark on the oil pump cover. Using the J 42069-10 or other suitable tool gm_car_cad_cts_04_j42069-10.gif

  5. Install the J 42069-10 or other suitable tool to the crankshaft sprocket with the knurled bolt.
  6. Rotate the crankshaft in the engine rotational direction, clockwise using the J 42098 until the lever of the J 42069-10 or other suitable tool firmly contacts the water pump pulley flange. The # 1 cylinder is at TDC at this point.
  7. Secure the moveable lever of the tool to the water pump pulley flange. Tools in cam gears gm_car_cad_cts_04_tools_in_cam_grs.gif

  8. Install the J 42069-1 and the J 42069-2 or other suitable tools to the camshaft gears. If the J 42069-1 or the J 42069-2 or other suitable tools do not fit into the teeth of the camshaft gears, it may be necessary to loosen the upper idler pulley and turn the eccentric or camshaft gears until the tool can be inserted.
  9. Loosen the timing belt tensioner nut.
  10. Loosen the upper idler pulley bolt.
  11. Remove or disconnect the following:
    • Lower idler pulley bolt
    • Lower idler pulley and spacer
    • J 42069-10 or other suitable tool from the crankshaft sprocket WARNING
      After timing belt is removed, never turn camshaft and crankshaft independently. Do not remove J 42069-1 and the J 42069-2 or other suitable tools while the belt is removed.
    • Timing belt
prev.gif next.gif

Dec 18, 2010 | 2003 Cadillac CTS

1 Answer

Need to know what the degree the timing should be for a4.9 Cadillac Engine ?


The 1991 Cadillac DeVille 4.9 engine incorporates a magnetic timing probe hole for use with special electronictiming equipment. Malfunction codes may be set during ignition timing adjustment procedure.Enter diagnostics and clear trouble codes if this occurs.#1 Place transmission in park .#2 With the ignition in the Off position attach a timing light to #1 spark plug cable .#3 With engine at normal operating temperature and air conditioning OFF,take off the air cleaner upper housing. The engine should be OFF at this point.#4 Jump pins A and B at the ( ALDL) connector.while not in diagnostic display.SET TIMING MODE message will apear on the climate control Driver Information center.#5 Start the engine and aim the timing light the timing mark loosen the distributor hold-down nut. While observing the timing mark, rotate distributor untill the line indicates the correct timing .This sets the base timing at 10 degrees BTDC at any speed under 800 RPM in the (PCM) The PCM controles the timing throughout the intire engine RPM range.This is the best imformation I can offer you good luck.

Dec 05, 2010 | 1991 Cadillac DeVille

1 Answer

2003 CTS 3.2L threw serpentine belt. Car made no


you bent a rod get the motor from someone other than dealer they will soak you

Oct 03, 2009 | Cadillac CTS Cars & Trucks

1 Answer

HOW TO REPLACE CAM SHAFT SENSOR


Chances are your cam sprocket is off one tooth, bring the engine to Top dead center #1 cylinder firing stroke lining up the flywheel timing pointer notch to the timing marked zero. remove the timing belt cover to check that the timing marks line up if not remove tensioner and reset the sprocket so it lines up then reinstall tensioner recheck.

Sep 11, 2009 | 2002 Volkswagen Passat

1 Answer

My friend owns a 2003 cadillac cts 3.2 ltr engine. he needs to replace his timing belt because it broke but there are multiple timing marks on the harmonic balancer and 4 marks on the block, so he doesnt...


If the timing belt broke, he should take it to have it replaced because theres more than likely to be bent valves in the head. Heads should be checked before putting another timeing belt on. If there is valve damage, then more than likely there damage to the pistons too.

Dec 13, 2008 | 2003 Cadillac CTS

3 Answers

Installing a serpentine belt on a 2003 cadillac cts


There is a belt routing sticker under the hood, other than that and a few hand tools there is a problem to replace this belt.

Nov 21, 2008 | 2003 Cadillac CTS

Not finding what you are looking for?
2003 Cadillac CTS Logo

324 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...