Question about 2006 Ford Escape

1 Answer

2006 ford escape 3.0 v6 camshaft sensor location

Cam sensor location

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 496 Answers

It should be on the left cylinder head just below the valve cover.

Posted on Apr 17, 2015


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 1102 Answers

SOURCE: How and where do I

The sending unit will be in the tank and is an integral part of the fuel pump assembly, You will have to take the tank out to change it.

Posted on Jan 15, 2011

Testimonial: "Thank you for your quick response, not what I was hoping to hear but what I expected. Your information tells me how I will be spending my day off."

  • 1902 Answers

SOURCE: O2 sensor

On the left front part of the engine, near the bottom, you also have a second one underneather the car right past the engine towards the rear of the car

Posted on Feb 08, 2009

  • 2049 Answers

SOURCE: location of the bank 1 sensor 2 O2 sensor on a 2001 ford escape

B1 means the sensor is located on the same bank of the engine that has the #1 cylinder. B2 is located on the opposite bank.
S1 means the sensor is located BEFORE the catalytic converter
S2 means the sensor is located AFTER the catalytic converter

You didn't say which engine you have, so I've included the diagrams of both 4 cyl and 6 cyl so you can see the banks


Posted on Oct 20, 2009

  • 85 Answers

SOURCE: Where is the camshaft position sensor on a 2000 Ford Explorer?

in the rear like where the dist would normaly be

Posted on Dec 31, 2009

  • 80378 Answers

SOURCE: where is the camshaft position

if u look on the drivers side of the top of the engine the cam sensor is in the block where the distrutor used to go, here is a picture of it4fd7155.jpg

Posted on Sep 08, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2006 ford escape v6 shuts off on me going down the road at 45 mph anyone know what it might be please help me

Could be a lot of thing's , engine sensors - crankshaft position sensor , cam sensor , or PCM engine computer .Does it start right back up ? Videos on you tube for testing crank an cam sensors ! Is the check engine light on ? Have vehicle checked for DTC'S - diagnostic trouble codes .

Oct 15, 2016 | Ford Cars & Trucks

1 Answer

Where is the camshaft position sensor located on a 01 escape with a 3.0

Near the teeth of the camshaft hard to c just check near the cam

Sep 02, 2016 | 2001 Ford Escape

2 Answers

Where is the cam sensor located on a 2006 cobalt 2.2

Apr 17, 2015 | 2006 Chevrolet Cobalt

1 Answer

Where is the camshaft postion sensor on the 07 ford edge with the 3.5 v6?

Locate the cam sensor wiring harness from underneath the vehicle at the front of the engine block near the crankshaft pulley.

Read more :

Jun 12, 2014 | 2007 Ford Edge SEL Plus

1 Answer

Camshaft timing

yes it has to shoot up

Jan 06, 2014 | 2006 Ford Escape

1 Answer

Location of camshaft sensor on a 2006 ford 500 awd limited 3.0 v6

It should be located in the valve cover, towards driverside.

Jan 18, 2011 | 2006 Ford Five Hundred

1 Answer

Locatio camshaft sensor 05 frontier 4.0 v6

on the back of the cylinder head. hard to see, but there is a connector with green slide piece inside of it. that is the location of cam sensors.

Sep 21, 2010 | 2006 Nissan Frontier

1 Answer

2004 escape where is the crank position sensor located?

We would recommend taking a look at the front of your motor, by either of the camshafts and where they exit the head(s). The sensor is either a optical or hall effect sensor, so try and find a housing that is near or around your intake or exhaust camshaft ( or just single camshaft) for the location of your camshaft position sensor

Jan 27, 2010 | 2003 Ford Escape

1 Answer

Ineed to know the location of the cam sensor on a ford escape 2002 with the 3.0 liter V6 DOHC

SECTION 303-14: Electronic Engine Controls 2002 Escape Workshop Manual REMOVAL AND INSTALLATION Camshaft Position (CMP) Sensor —3.0L (4V) Removal and Installation
  1. Remove the camshaft position (CMP) sensor.
    1. Disconnect the electrical connector.
    1. Remove the bolt.
    1. Remove the sensor.
#56 is the cam sensor. please rate as fixed if this is what you need.


May 02, 2009 | Ford Escape Cars & Trucks

Not finding what you are looking for?
2006 Ford Escape Logo

648 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides