Question about 2005 Suzuki Forenza

Open Question

Where the egr adapter gasket is located?

Any diagram available on line?

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the egr valve on a citizen c5


  • First you want to open up the hood of your car
  • Find the engine diagram sticker on the inside of the open hood and identify the mechanism that is labeled "EGR Solenoid" on the sticker.
  • Find the "vacuum line" on the sticker diagram and identify its color. This is the line that runs from the EGR solenoid to the EGR valve.
  • Locate the vacuum line inside the engine compartment of the vehicle toward the front of the driver's side. The vacuum line will be the same color on the vehicle as it is on the diagram.
  • Follow the vacuum line from the front of the vehicle where it connects to the EGR solenoid through the conduit that carries it to the EGR valve at the rear of the engine compartment. The easiest way is to track the uniquely colored vacuum line along the path between its two connection points. The vacuum line connects to the EGR valve, which is the disk-shaped object located at the rear of the engine compartment
    on the driver's side.

May 04, 2016 | Cars & Trucks

2 Answers

Egr valve


Below is a link for instructions for the removal and installation of the EGR valve along with a diagram. Best of luck.
Greg
97 Buick EGR

Nov 04, 2009 | 1997 Buick LeSabre

3 Answers

EGR problem on 2001 Camry??


Replace filter in EGR Modulator located to the left of EGR valve.
How do you clean the intake port below the EGR valve?

Sep 30, 2009 | 2001 Toyota Camry Solara

3 Answers

Egr valve flow insufficient


Check for

vacuum leaks on intake manifold,

the air tube between the air filter.

intake manifold vacuum hose.

===
clean throttle plate with Berryman carburator cleaner

SEE sample picture HERE
===

Also remove carbon built up behind the EGR valve and the EGR passage tube.

===

Vacuum leak WILL offset the intended 14.7 to 1 air fuel ratio.

More un-metered air (leaks) will lean out the fuel mixture.

Use small amount of Berryman carb clearer at potential air leak area will help you identify trouble spot.

At idle,just spray and listen for the RPM surge.

The in-rush of carb clearer will increase the RPM on the motor.

Record the problem spot(s) and address it later.

===

EGR carbon built up require 2+ hours to clean from start to finish.

You will need a new EGR base gasket before your start.

Locate and remove the EGR valve after the vehicle is cool down.

Carefully record the connector and vacuum line (for older vehicle) location by drawing an easily to follow diagram.

Remove the EGR valve.

Inspect the location of the carbon built-up inside the valve and the EGR passage tube.

SOAK these areas with WD-40 spary.

You will need a small screwdriver,cloth hanger and lot of newspaper and time to get this cleaning done right.

RE-SOAK the carbon and let it sit for over-night will also help.

One the last round,pass a shop vacuum of the EGR valve and the passage pipe.

Install the new EGR gasket and connectors.

Allow the vehicle to warm up outdoor to burn up any remaining WD-40.


Take it for a test drive.


Please rate my answer if it's useful to you.


Cheers,

Mustgo

Sep 25, 2009 | 1999 Chevrolet Malibu

3 Answers

Check engine light on,obd code P0402 I can hear leaking air under neat


code should be for egr flow - air leak you hear could be egr pipe or tubing rusted out or broken

Sep 24, 2009 | 2001 Toyota Camry

2 Answers

2003 Lancer rough ildle


ts runing high 2300 check the vacuum with a gauge and unplug egr lines ..egr could be plugged ..oxy sensor could be open loop running rich...tps ar air flow meter ...

May 08, 2009 | 2003 Mitsubishi Lancer

1 Answer

Check engine light on when check it insufficent EGR valve


yes the passages can be cleaned. They pass exhaust gas into the intake maniflod for reburning.

It could be the DPFE that controls the EGR too. Diff. Pressure Feedback EGR.

there is also a vacuum regulator valve and a solenoid too.

Please rate as fixya if this helps.

----------------
Exhaust Gas Recirculation (EGR) Valve —3.0L (2V) Removal and Installation
  1. Disconnect the exhaust gas recirculation (EGR) valve (9D475).
    1. Disconnect the vacuum line.
    1. Disconnect EGR tube nut.
  1. Remove the EGR valve.
    • Remove the two bolts.
    • Remove and discard the gasket.
  1. NOTE: The sealing surfaces are soft metal.
    To install, reverse the removal procedure.
    • Carefully clean both sealing surfaces and install a new EGR valve gasket.
2d0d879.gif
--------------------------------------
EGR Valve —3.0L (4V) Removal and Installation
  1. Remove the EGR valve (9D475).
    1. Disconnect the vacuum line.
    1. Disconnect the EGR tube.
    1. Remove the EGR valve and discard the gaskets.
e56a6e2.gif
  1. NOTE: The EGR valve sealing surfaces are soft metal.
    To install, reverse the removal procedure.
    • Carefully clean all sealing surfaces and install new EGR valve gaskets.

Apr 07, 2009 | 2000 Mercury Sable

1 Answer

1994 Sonoma just threw a code 32 EGR Valve do you have a diagram of the motor or can you tell me where it is located?


Your EGR valve is located behind your throttle body and injectors, and it is attached to the intake manifold. It has two bolts on opposite sides of the valve and a vacuum line running out of it. Disconnect the vacuum line, remove the two bolts, and pull off the EGR valve. The EGR's on these trucks tend to get clogged up with carbon and stick. Take some carb and choke cleaner, and a small pick or very small flat head screw driver and break up the carbon inside of the valve. Be careful not to puncture the rubber diaphragm or you EGR will be no good after you get done cleaning it. Once you get all of the carbon deposits out of the EGR, assuming you buy a new gasket for it, put the gasket between the valve and intake manifold, tighten screws, and plug the vacuum line back in. This should solve your problem!

Dec 02, 2008 | 1994 GMC Sonoma

Not finding what you are looking for?
2005 Suzuki Forenza Logo

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...