Question about 2003 Chevrolet Silverado 1500

Open Question

How do I get the clip back on after replacing brake light switch

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 314 Answers

SOURCE: Brake Light Switch replacement

The best bet is to check-out the new one, it should come complete. Frankster016

Posted on Oct 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Free 2006 gmc envoy brake light switch replacement procedure


Remove the panel under the dash. Look at the brake pedal and follow it up to the brake light switch. Two wires going to it. there is a plastic clip that holds it in place, Pull it off. The clip comes with the new switch. Replace it. To easy. Have a flash light to see..

Oct 26, 2014 | 2006 GMC Envoy

1 Answer

How do I replace the brake light switch on a 2001 gmc sierra


Follow the brake petal up to the brake rod. Unplug the switch wire then take the clip of the petal then the brake light switch should slide right off.

Aug 09, 2014 | GMC Sierra Cars & Trucks

2 Answers

1995 class a motor home ford chassis brake light switch


The switch is located on the brake peddle where the master cylinder attaches to the peddle remove clip slide master cylinder rod to one side remove switch.

Oct 08, 2013 | Cars & Trucks

1 Answer

I'm trying to change my brake light switch on my 1995 gmc Yukon. I can't figure out how to take the clip off that hold the switch on


Most GM brake light switches are held in the hole by a steel clip that grabs on the plastic threads. To remove the switch, you just grab the switch and pull it out. Requires a little effort. When you replace the switch, it pushes back into the clip fairly easily as the clip has one way tabs. You push the switch in until it bottoms out on the brake pedal arm. The threads are just there for the clip to grab onto. In rare cases where the clip fails to retain the switch, I have had to screw a nut onto the back side of the switch to prevent it from backing out of the clip. This is the case sometimes when you are reinstalling the same clip. Otherwise a new one will generally hold because of the new plastic threads.

Dec 12, 2012 | Cars & Trucks

2 Answers

No brake lights


If the fuses are ok, replace the brake light switch on the back side of the brake pedal. You can test it by disconnecting the plug from the switch and use a jumper wire or paper clip between posts on the plug, lights come on, bad switch.

Mar 18, 2011 | 2001 Chevrolet Cavalier

1 Answer

No brake lights need to replace brake light switch


Its on the top of the brake pedal. Unplug the connector and check for 12 volts firstif you have a multimeter set it 20 DC volts you should get 12 at connector. If thats good set the meter to OHMS low scale take jumper leads connect to switch terminals aliagator clips then clip to the probes on the meter and push the brake pedal the reading should change if the switch is good from open when depressed to closed when no force applyed to the brake pedal. If there is no change then the switch needs to be replaced. Remove the clip from the pin that slides through the pedal and the switch slide out the pin install new switch reconnect the connector slide pin back in and install the clip. check to see if brake lights work

Dec 23, 2010 | 1995 Chevrolet Tahoe

2 Answers

My 1995 Chevy Tahoe brake light switch wont stay in position and the brake lights stay on. I replaced the switch and had the same problem.


Brake Light Switch REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Disable the SIR system (if equipped).
  3. Remove the clip (R/V Series) or unclip the switch (C/K Series) and unplug the electrical connector from the brake light switch.
  4. Remove the switch.
  5. Installation is the reverse of removal.
prev.gif next.gif

Oct 07, 2010 | 1995 Chevrolet Tahoe

1 Answer

I have a 2003 buick lasabre, brake lights stay on include back window light


Most likely the brake light switch is sticking on. This switch is mounted on the brake pedal arm about six inches above the foot pedal, between the arm and the push rod that goes into the master cylinder.
Get a new switch at the auto parts store, then pull the spring clip and slide the old switch off. disconnect the wires, replace the switch and put the spring clip back into place.
If you don't want to replace it yourself, it should be an inexpensive repair (I'd guess under $100). Call around for prices.

Sep 01, 2010 | 2003 Buick LeSabre

2 Answers

Brake Light Switch clip on 94 GMC Pickup


My 1996 Brake light clip needed to spread open with a screw driver(some what like a round spring) and with another screw driver push the switch up the pin. The switch will push the clip off the Pin. The pin has a head that needs to clear clip while the spring clip is spread open. It took me a while to figure out.

Aug 15, 2008 | 1995 GMC Yukon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...