Question about Ford Bronco II

1 Answer

Bronco2 with 2.9lV6. I asked about no power from coil to dist. I have power at coil 11.8. and continuity going to dist. No plugs firing. In process of buying new dist. and TFI mod. Checking grounds.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert that has over 500 points.

  • Ford Expert
  • 244 Answers

The distributor can be serviced but the tri is the problem.

Posted on Apr 28, 2015


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 79865 Answers

SOURCE: 1990 jeep wrangler

Check the MAP sensor. To see if this is the problem, assuming that the Jeep won't start but is turning over, unplug the MAP sensor and then plug it back in. If you can start it now, the MAP sensor needs to be replaced. The MAP sensor is located in the engine compartment, where the firewall meets the body at the top of the engine compartment, on the driver's side.

Posted on Jul 30, 2008

  • 4 Answers

SOURCE: 95 Geo metro will not crank no fire

take your timing cover off have a friend look to see if the belt is moving while you crank the engine i would say that the belt is broken

Posted on Dec 16, 2008

  • 4669 Answers

SOURCE: no spark to plugs or coil.

Do you have power to the coil with the key in the run position and when cranking? (ignition switch)

Posted on Mar 26, 2009

  • 135 Answers

SOURCE: weak spark from dist cap to plugs. spark from coil

The engine is definitely in an over rich fuel condition if you are blowing black smoke. I would suspect a bad 02 sensor, but the flooding condition you describe at starting could be other things. I would check the codes and proceed from there.

Posted on Jul 13, 2009

  • 154 Answers

SOURCE: car wont start Has no spark.has power going into

there are 2 coils in the dist

Posted on Aug 01, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

88 Ford F-250 won't start replaced dist coil icm still no fire from coil to dist

Check for power and ground at the coil and ignition module.. Bad wires/plugs.

Oct 18, 2016 | Ford Cars & Trucks

1 Answer

Tractor will not start

Tractor model make and year ?

Aug 25, 2015 | Cars & Trucks

1 Answer

Could my distribitor be bad?

is there a dist first or a coil pack are all the plugs good and do they have spark on each when you say it fires on 2 cyls which ones and do you have a check engine on you can check the codes and it should help you but if you have a dist you also have a rotor as well by removing the cap you should see corrosion under where the rotor hits on as well you have a pickup coil but dont go so far check plugs first for ware then go from there wires, coils, etc

Aug 06, 2014 | 2003 Ford Ranger Regular Cab

1 Answer

No power to spark plugs

V6 or V8 ? Both engines use a flat cap and standard rotor.
The coil is triggered by two modules, one inside the bottom of the dist and the other mounted on or near the coil. Any of these parts could fail.
You would check to see if all of the plug wires are dead, and if the coil and module has batt voltage with the key on. Also check to see if the coil will fire if not connected to the dist cap.

Jun 26, 2012 | 1994 Chevrolet Caprice Classic

1 Answer

Plugs are not firing on left bank. Replaced dist. wites plugs and the dist. itself

Are you sure its not a fuel issue? If you replaced the Dist cap, Rotor,Wires,Plugs and the main Distributor, spark should not be an issue. Unless the coil isn't producing enough juice to fire all cylinders. I would replace the coil.

Dec 15, 2011 | 1989 Subaru Gl Wagon

1 Answer

Will not start no fire a plugs 1994 sub 350

Check the distributor ignition module in the distributor. Also check to see if you have power going into the distributor. If you do, It's a safe bet that the distributor is bad. Check the cap and rotor if they haven't been changed in awhile. Order of cheapest to most expensive is actually. Power into dist. Cap and rotor, then Dist/module.

Mar 14, 2010 | 1994 Chevrolet Suburban

1 Answer

I changed my dist. cap on 1990 chevy p/u took one

Is the coil connected to the ditributor? did you knock any connections off in the process? Does it turn over but not fire? do you have spark at the plugs? Are you sure of cylinder location in respect to firing order? Did you-and check this first as with any elec. problems-blow a fuse in the ignition circuit? good luck!

Jan 01, 2010 | 1990 Chevrolet C1500

1 Answer

There is no power going to the dist cap. I put a new coil in but this did not fix it. The spark plugs will not fire. Everything works but the plugs will not fire. The engine just turns. Ichecked the wires...

U have a power wire that has been breached ur gonna have to check continuity to ur power wire at the coil and dist hook one lead to the fuse that supplies power and other lead to to same circuit under hood at coil repeat step with all wires on coil and dist just to be sure.

Apr 03, 2009 | 1992 Plymouth Voyager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides