Question about Cars & Trucks

1 Answer

Fill pipe cleaning

Fill pipe sys

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Cars & Trucks Expert
  • 150 Answers

There is not much to go on here. Is it belching fuel back out of the fuel tank when your putting gas in. If so, there is a vent tube that goes down into the tank and if it is out of place, the tank can't get air while your fueling. Check your fill tube.

Posted on Apr 04, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Thermostat replacement 2002 rendezvous


Thermostat Removal & Installation 3.4L & 3.5L Engine To Remove:
  1. Drain the coolant below the level of the thermostat.
  2. Remove the air cleaner and duct assembly.
  3. Remove the exhaust crossover pipe.
  4. Disconnect the radiator hose from the thermostat housing. gm_mv_ven_tstat.gif

  5. Remove the mounting bolts and remove the thermostat housing.
  6. Remove the housing gasket.
  7. Remove the thermostat.
  8. Clean the mating surfaces.
To Install:
  1. Install the thermostat on the engine. NOTE: Apply RTV sealer to the thermostat housing bolt threads.
  2. Install the thermostat housing and gasket with the mounting bolts. Tighten 18 ft-lb (25 Nm).
  3. Connect the radiator hose to the thermostat housing.
  4. Install the exhaust crossover pipe.
  5. Install the air cleaner and duct assembly.
  6. Fill the cooling system.
  7. Check the cooling system for leaks.
3.6L Engine To Remove:
  1. Remove the air cleaner.
  2. Remove the throttle body.
  3. Remove the heater pipes.
  4. Remove the coolant inlet pipe. Thermostat 3.6L gm-03-36-2447.gif

  5. Remove the thermostat mounting bolts and remove the thermostat.
  6. Clean the thermostat and heater pipe mating surfaces.
To Install:
  1. Place the thermostat in the housing with a new gasket.
  2. Install the thermostat and gasket on the engine with the mounting bolts. Tighten 89 in-lb (10 Nm).
  3. Install the coolant inlet pipe.
  4. Install the heater pipes.
  5. Install the throttle body.
  6. Install the air cleaner.
  7. Fill the cooling system and perform a leak test.
prev.gif next.gif

Dec 19, 2010 | 2002 Buick Rendezvous

1 Answer

What do i do when its over heating? how do i install thermostat?


Thermostat Removal & Installation 3.4L & 3.5L Engine To Remove:
  1. Drain the coolant below the level of the thermostat.
  2. Remove the air cleaner and duct assembly.
  3. Remove the exhaust crossover pipe.
  4. Disconnect the radiator hose from the thermostat housing. gm_mv_ven_tstat.gif

  5. Remove the mounting bolts and remove the thermostat housing.
  6. Remove the housing gasket.
  7. Remove the thermostat.
  8. Clean the mating surfaces.
To Install:
  1. Install the thermostat on the engine. NOTE: Apply RTV sealer to the thermostat housing bolt threads.
  2. Install the thermostat housing and gasket with the mounting bolts. Tighten 18 ft-lb (25 Nm).
  3. Connect the radiator hose to the thermostat housing.
  4. Install the exhaust crossover pipe.
  5. Install the air cleaner and duct assembly.
  6. Fill the cooling system.
  7. Check the cooling system for leaks.
3.6L Engine To Remove:
  1. Remove the air cleaner.
  2. Remove the throttle body.
  3. Remove the heater pipes.
  4. Remove the coolant inlet pipe. Thermostat 3.6L gm-03-36-2447.gif

  5. Remove the thermostat mounting bolts and remove the thermostat.
  6. Clean the thermostat and heater pipe mating surfaces.
To Install:
  1. Place the thermostat in the housing with a new gasket.
  2. Install the thermostat and gasket on the engine with the mounting bolts. Tighten 89 in-lb (10 Nm).
  3. Install the coolant inlet pipe.
  4. Install the heater pipes.
  5. Install the throttle body.
  6. Install the air cleaner.
  7. Fill the cooling system and perform a leak test.
prev.gif next.gif

Sep 18, 2010 | 2002 Pontiac Aztek

2 Answers

Where is the thermostat on a 2.2l ohc engine?


Removal & Installation 2.2L VIN 4 To Remove:
  1. Drain the cooling system.
  2. Remove the lower radiator hose from thermostat housing.
  3. Remove the thermostat housing bolts and outlet.
  4. Remove the thermostat.
  5. Clean the mating surfaces.
To Install:
  1. Install the thermostat.
  2. Install the thermostat housing and bolts.
  3. Install the coolant housing bolts. Tighten bolts to 14 Nm (10 ft. lbs.).
  4. Install the lower radiator hose to thermostat housing.
  5. Fill the cooling system.
  6. Inspect for leaks.
2.2L VIN F To Remove:
  1. Remove the exhaust manifold. If equipped with an automatic transmission.
  2. Drain the cooling system.
  3. Remove or disconnect the following: chevy_cav_02-04_tstat.gif

    • Thermostat housing to water pump feed pipe bolts. chevy_cav_02-04_feedpipe.gif

    • Thermostat housing to water pump feed pipe.
    • Thermostat.
To Install:
  1. Install or connect the following:
    • Thermostat.
    • Thermostat housing to water pump feed pipe.
    • Thermostat housing to water pump feed pipe bolt. Tighten bolt to 10 Nm (18 in. lbs.).
    • Exhaust manifold. If equipped with an automatic transmission.
  2. Fill the cooling system.
2.4L VIN T To Remove:
  1. Drain the cooling system.
  2. Remove the exhaust manifold heat shield bolts and shield. cavman.gif

    cavtstat.gif

  3. Remove the coolant inlet housing bolts.
  4. Lift vehicle.
  5. Remove the coolant inlet housing stud from the oil pan.
  6. Remove the wheel.
  7. Remove the right engine splash shield.
  8. Remove the transaxle-to-engine block brace bolts and brace.
  9. Remove the radiator outlet pipe.
  10. Remove the thermostat.
  11. Clean the mating surfaces.
To Install:
  1. Clean the mating surfaces.
  2. Install the thermostat.
  3. Install the radiator outlet pipe.
  4. Install the transaxle-to-engine block brace and install bolts.
  5. Install the right engine splash shield.
  6. Install the wheel.
  7. Lower the vehicle.
  8. Install the exhaust manifold heat shield and bolt.
  9. Tighten the exhaust manifold heat shield bolts to 14 Nm (10 ft. lbs.).
  10. Fill the cooling system.
  11. Inspect the system for leaks.
prev.gif next.gif

Sep 09, 2010 | 2003 Pontiac Sunfire

2 Answers

How do you replace the fuel pump on a 2001 camaro


Camaro, Firebird, 1999 - 2002 Repair Guide
Fuel Pump - Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Relieve the fuel system pressure.
  3. Drain the fuel tank.
  4. Clean the area surrounding the sender assembly to prevent contamination of the fuel system.
  5. Remove or disconnect the following:
    Fuel tank Fuel sender-to-fuel tank retaining ring Fuel sender from the fuel tank Fuel pump from the sending unit

    46aa2e5.jpg
    Fig. Fuel sender/pump assembly component identification
To install:
  1. Install or connect the following:
    NOTE The fuel pump strainer must be in a horizontal position and must not block the float arm travel.
    Fuel pump with new strainer onto the sending unit New O-ring in the tank opening groove New O-ring on the fuel sender feed tube
  2. Fold the strainer over itself and slowly position the sending assembly in the tank so the strainer is not damaged or trapped by the sump walls.
    Retaining ring Fuel tank. Torque the bolts to 33 ft. lbs. (45 Nm). Fuel filler cap Negative battery cable
  3. Turn the ignition switch to the ON position for 2 seconds, OFF for 10 seconds, then back to the ON position. Check for fuel leaks.

Hope this help (remember rated and comment this), good luck.

Mar 18, 2010 | 2001 Chevrolet Camaro

1 Answer

No heat from defrost


SOUNDS LIKE YOU MAY HAVE AIR BLOCK, OR BLOCKED HEATER MATRIX, CHECK FIRST CHECK THE HEIGHT OF THE HEATER MATRIX IN THE CAB , IF ITS HIGHER THAN THE FILLER/EXPANSION TANK. THEN COULD BE AN AIR LOCK, LOOK FOR THE HIGHEST PIPE AND SEE IF THERE IS A BLEED VALVE, IF NOT TAKE BOTH PIPES OFF THE MATRIX FEEDS (TWO PIPES GOING FROM ENGINE BAY TO INSIDE OF CAR, AND FLUSH OUT WITH HOSE TO SEE IF IT IS BLOCKED, AND RECONNECT LOWEST PIPE FIRST AND FILL SYSTYM TILL WATER APPEAR FROM TOP AND RECONNECT RUN MOTOR, AND KEEP TOPIN UP, YOU CAN BY A COOLENT FLUSH SOLUTION TO CLEAN THE SYSTYM OUT

Dec 20, 2009 | 1995 Oldsmobile Achieva

6 Answers

2005 Ford Crown Victoria Trouble filling gas tank. Gas backs up in the filler nck and clicks pump off. Have to run as slow as pump will run to fill.


The tank vent pipe may be blocked or kinked, it usually branches off the main tank filler pipe and can be seen from under the car.

Oct 23, 2009 | 2005 Ford Crown Victoria

2 Answers

With tank empty I can't use the full pump pressure of the gas pump. Nossle stop like tank is full enen when I first start to fill the tank.


check for clogged fuel vent on fiel tank, it has a charcoal cannister that is vent for the tank, probably clogged... please rate my help, thanks...

Aug 05, 2009 | Hyundai Motor 2002 Sonata

1 Answer

I put engine oil in power steering oil tank!!!


u need to drain the whole system out, take the pipe off at the power steering resoviour and take all the fluid out. next connect the supply pipe and fill up the resoviour, next put the return pipe in a suitable container to collect the old fliud. keep filling and emptying the fliud untill you can see clean fliud (like cherryade). thats it

Feb 18, 2009 | 2003 BMW 325

1 Answer

1981 Vanagon (air cooled) hot stutter


change the flexible feed pipe for the servo it runs off the inlet manifold left side to a metal pipe,if this goes porous then idle is rough brakes dont work right and as it get hot it will run like a demented old woman who smoke 80 a day

Sep 20, 2008 | 1986 Volkswagen Wagon Camper

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...