Question about Cars & Trucks

1 Answer

Only half clutch pedal wen running - Cars & Trucks

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 3,519 Answers

Hi:
You don't tell us what we're dealing with so will go with general principles:
- Manual clutch? Check linkages, adjust slack. Possible that clutch is worn, throwout bearing?
- Hydraulic clutch? Same thing only also check fluid level, master & slave cylinder function, fluid leaks.

Posted on Apr 04, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clutch pedal is stuck half way down wont shift gears


Check clutch cable, check clutch lever, if there is some noise from the clutch when the engine is running, then the release bearing is most likely faulty, or even the clutch pressure plate.

Apr 16, 2014 | 1997 Subaru Impreza

1 Answer

I just put a new clutch in my 04 elantra and its stuck into gear wot do i do


clutch is not disengauging when the motor is running could have put clutch plate in wrong way do you have a good clutch pedal,did you clean of new pressure plate might have had a sticky coating on it

Dec 27, 2012 | 2004 Hyundai Elantra

1 Answer

My 2002 1.8 mondeo holds back on power wen driven at town speed and engine cuts of wen driving but dip the clutch and engine will run again. any ideas


Have you checked the fuel filter? It may be time for a change. In a Manual transmission when it dies any time as long as your still rolling at a decent rate of speed you should be able to push the clutch in to start the engine back on.

Sep 20, 2012 | Cars & Trucks

1 Answer

2002 1.3 Kia Rio. Pushed in clutch pedal, heard metallic pop, half a piece of a metal ring + half a clip sitting in driver's footwell. Pedal will depress and release but clutch wont engage


I had this same problem the cable is fine its a clip on outer cable to stop it mooving when you press clutch mine poped when I tightened the clutch cable still don't have solution though waiting to payday to take it to garage

Mar 22, 2012 | 2002 Kia Rio

1 Answer

No light wen i press the brake pedal


check fuse for brake, in one instance i had to adjust brake light switch on brake pedal a half turn or so and that fixed it.

Dec 31, 2010 | 2004 Nissan Sentra

1 Answer

Cluth pedal feels the same only clutch wont disengage on a 92 dodge stealth


i had this problem for awhile and found out it was the clutch pedal assembly... push ur clutch pedal down a few times then reach down and pull up on it, give it a good tug! if it moves up half an inch or more, your clutch peddal ***. needs a rebuild. jus a few bushings, u can get em from sheptrans. they even have clutch pedal

Dec 20, 2010 | 1992 Dodge Stealth

1 Answer

Clutch issue after throwout bearing instal


once you have bled out all the air ,if the pedal still engages right down then suspect the fingers on the release plate are worn.Never replace a part of the clutch, allways change all 3 components,it save all the hastle of taking it to bits again and again.

May 21, 2010 | 2003 Nissan 350Z

1 Answer

Wen trying to crank wont start just spin over and


at the top of the clutch pedal is a switch that has to be replaced or you can hook the two wires together. this may be problem.

Apr 04, 2010 | 1996 Chrysler Sebring

1 Answer

You have to push clutch pedal within a half inch of floor before clutch will engage or disengage. used to be that pedal would only need to be pressed half way.


Check the fluid level in the reservoir below the brake booster,it's the clutch slave cylinder reservoir and it need to be full of d.o.t. 3 brake fluid.

Dec 19, 2009 | 2006 Hyundai Tiburon

1 Answer

How do I bleed the clutch slave cylinder on a 1993 Dodge Dakota Sport 2wd?


should be self bleeding if pedal is set correct

pedal rod needs 1/8" free play to clutch master clydinder plunger

fill clutch res slowly let bubbles bleed

then only half strokes on the clutch pedal with 30sec pause between pumps

Mar 19, 2009 | 1993 Dodge Dakota

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...