Question about 1998 Dodge Stratus

Open Question

Where is the Input Speed Sensor on a 1998 Dodge Stratus ?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1861 Answers

SOURCE: MAF Sensor 2004 Dodge Stratus

If your car has a MAF (Mass Air Flow) sensor, it would be located in the air delivery tube that runs from the air filter box to the throttle plate assembly on the intake manifold. It will have a wiring connector going to it, also. The MAF does exactly what it is called: It "senses" the volume, or "mass" of the air-flow; thusly it needs to be in the intake air tube. If you do NOT have such a device in the air-tube, you have a MAP sensor, (Manifold Absolute Pressure); this is another way of measuring the same air volume, albeit older technology. You will commonly find this device on the firewall, with a vacuum line running to the intake manifold.

I hope that this sheds some light on your question.

Thanks for choosing FixYa for advice!

Posted on Mar 06, 2009

Ad
  • 154 Answers

SOURCE: location of speed sensor a for 99 dodge intrepid

The "Vehicle Speed Sensor" signal is generated by the transmisson output speed sensor. That is the one located at the rear of the case. It is externally mounted. That supplies "vehicle speed" info to the other On-Board Computers. The input turbine speed sensor is located just behind the bell housing area of the case. I believe the trans controller is the only module that needs that info. The Crank Position Sensor give engine RPM info and it is located on the bell housing near the engine block. I hope this helps.

Posted on Apr 02, 2009

  • 1 Answer

SOURCE: transmission input speed sensor location

It is located on the front of the transmission. you will see 2 of them one on the left under small transmission lines it is the input then to the right behind the radiator overflow there is the other one. Easiest way to change them is with a 1" deep well socket

Posted on Jun 02, 2009

polarcycle
  • 1392 Answers

SOURCE: 2004 DODGE STRATUS 2.7L, Location of Crankshaft Position Sensor?

it is located on the right side of the motor, in the trans area. Actually in the bell housing.

Posted on Jun 23, 2009

Molson02536
  • 3854 Answers

SOURCE: p0700 p0720

Check the wire harness, make sure there are no breaks or crushed wires. Also check the wire harness to the TCM, look for any loose connections. Good luck and keep me posted. Be glad to help. 

Posted on Jun 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1998 dodge stratus is acting strange, chugging & stuttering. I just replaced the oil valve cover gaskets, replaced the crank sensor, distributor, put in new spark plugs, s.p. wires & a new battery. The...


get the OBD codes read as will point to the sensor/switch/circuit causing the issue, also use a fuel addative get one that covers the cat convertor as well as the valves , injectors etc ,take for a longish drive at a highish speed to get the engine at a good operating temp

Oct 24, 2014 | 1998 Dodge Stratus

1 Answer

How do I remove the input/turbine speed sensor? I have the R/T v6 3.0L Coupe


MAKE SURE YOU IGNITION KEY OFF POSITION. YOUR VECHICLE SPEED SENSOR IS LOCATED IN THE INPUT SHAFT HOUSING NEXT TO TWO FLUID COOLING LINES TO REMOVE IT YOU REMOVE ELECTRCAL CONNECTOR FROM FROM THE VSS.THEN REMOVE THE VSS SENSOR OUT OF TRANSAXLE.REPLACE O - RING THEN INSTALL THE NEW VSS OR VECHICLE SPEED SENSOR.

Nov 25, 2010 | 2001 Dodge Stratus

1 Answer

I'm trying to see where the speed senor is located at on my dodge stratus 1999... Can't find it on-line


There are two sensors located on the driver's side of the transmission. there is an input and and output sensor. You can only get to them from the underside of the car.

Sep 21, 2010 | 1999 Dodge Stratus

1 Answer

2000 dodge stratus tranny problems


there is no up shift sensor or down shift sensor,
there is a output sensor,input sensor,speed sensor,
you need to have your TCM checked to see which of these are at fault.

Dec 28, 2009 | 2000 Dodge Stratus

1 Answer

Car stuck in limp mode


THE INPUT SPEED SENSOR IS LOCATED JUST TO THE LEFT OF THE OUTPUT SENSOR..ABOUT 2-3 INCHES AWAY..SAME IDEA..2 WIRE PLUG AND IT UNSCREWS FROM TRANSMISSION..YOU WILL PROBABLY HAVE TO REMOVE THE TRANS CONTROLLER AND BRACKET FOR ACCESS..I HOPE THIS HELPS

Oct 11, 2009 | 1999 Dodge Stratus

1 Answer

1998 dodge stratus will not shift after engine swop


Check the input shaft and output shaft speed sensors on the transmission. One is likely bad.

May 26, 2009 | 1998 Dodge Intrepid

1 Answer

Transmission problem


P0715 - Input/Turbine Speed Sensor Circuit Malfunction


P0700 - Transmission Control System Malfunction

Feb 14, 2009 | 1997 Dodge Stratus

Not finding what you are looking for?
1998 Dodge Stratus Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...