Question about 2005 Nissan Quest

Open Question

How can i turn off the slip light

It stop working on motion

Posted by on

  • raj somaiya
    raj somaiya Apr 10, 2015

    Hi yomi sulaimon, There are many possibilities that can cause such problems. For step by step troubleshooting click the link below
    Free Car Repair Guide



Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why does my motion sensor light go on during the day? it is supposed to only turn on at night

Most likely the light sensor has stopped working. The light sensor creates voltage from light, like a small solar cell. If it quits producing voltage, the light system thinks it is dark.

Sep 28, 2017 | Cars & Trucks

1 Answer

After stopping theres a jolt in the drivetrain

check that you are not in 4 wheel drive H and on hard stand ( hard surface ) The jolt may be from drive train torque wind up releasing on the stop motion . wheel drive should only be used on loose surfaces --- mud--gravel---snow --ice or any surface that will allow the tyres to unwind the torque build slipping

Feb 09, 2014 | Mercury Mountaineer Cars & Trucks

1 Answer

Manual for EML Series ES100T 3 light motion sensor

The bulbs DO burn out occasionally, even after a short time. There are no markings on them that I can see. I have a unit. If it is the same as yours, it is a 100W 120v 8mm(G8 or GY8) Halogen (bi-pin). They also come in 35, 50, and 75W versions, if you don't need as much light.

Nov 16, 2011 | Cars & Trucks

1 Answer

Speedometor stopped working?? for 98 sunfire

there could be a trans or speed sensor problem. I dont know about the light reminder ?? I would have a trans shop check it first.

Oct 02, 2009 | 1998 Pontiac Sunfire

1 Answer

Transmission slips and reverse stopped working

you need your transmission rebuilt the clutches are slipping

Sep 28, 2009 | 2002 Chevrolet Tahoe

1 Answer

Pasenger side head light will not retract or open. can hear motor operating

perhaps something is obstruting it. Can you open manually? IF so, open, look at it closely and start with wd to loosen some of the mechanism. then, with assistance, have someone turn on lights and you can feel the motion and try to isolate it. If the motor is working, something else is stopping it from opening. Also, motors make noise sometimes, even when they aren't working correctly. Let's see where that takes you.

May 05, 2009 | Mercury Capri Cars & Trucks

2 Answers

AC blows cold while moving, and gets warmer while I'm stopped

There are two fans behind the radiator. One is suppose to begin running when the AC is turned on. The other is to cool the radiator when it gets too warm. Raise the hood with the engine running and AC "on"and see if at least one fan is running.

May 04, 2009 | 1995 Buick LeSabre

1 Answer


what do you mean not in motion. Are they both lights, one light, running engine not running. I would suggest looking at the connetor to the signal light fixture making sure its all the way locked in or even for a loose power or ground wire at the connector. Possibly the relay to the blinker is intermittent. I'm giving you a generalized solution because i'm not sure exactly what is wrong. Do you have the light on the dash board working and the signal light is not when it stops working do yo hear clicking. If you hear clicking for signal light is it fast or slow.

Aug 11, 2008 | Pontiac Sunfire Cars & Trucks

Not finding what you are looking for?
2005 Nissan Quest Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

76109 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides