Question about 2007 Hyundai Santa Fe

Open Question

Car is 2007 Hyundai Santa Fe 2.2 CRDTI diesel

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

kakee
  • 1268 Answers

SOURCE: HOW TO YOU GET AT PRESSURE SENSOR ON COMMON RAIL HYUNDAI SANTA FE 2007 CDX

This is what it looks like

47cf2f5.jpg

Posted on Oct 28, 2008

  • 566 Answers

SOURCE: 2007 Hyundai Santa Fe - Replacing fog light

hi have not had pleasure of this on santa fe yet? but will try to help dependant of which side o/s or n/s ? i would first remove the screws holding the front of the under engine plastic cover/shield and drop down sufficient to gain view/access? to the rear of fog lamp then if a cover is on? try turning anti clock to remove? or if rubber cover pull off? then the bulb and clip should be visible? unplug the wire from bulb then the spring clip holding bulb in place normally just sring the 2x top ends together and swing down/clear to remove bulb? refit new bulb correctly! pay attention to position old bulb positioned? then clip securely and re connect wire at this stage it would be best to ensure bulb works ?? before you re assemble all else? wish you luck and hope this helps with your problem ?

Posted on Oct 28, 2008

tabiri1
  • 1 Answer

SOURCE: hyundai santa fe 02 diesel

my 2001 hyundai santefe won't start. I diagnosed it and had this code, P0340 camshaft position sensor mulfunction, I checked the wiring system, replaced the cam sensor, but still keep having the same code. can anybody help me out?
secondly there is no current to the injectors. What do i need to do

Posted on Feb 11, 2009

  • 2 Answers

SOURCE: hyundai santa fe 2003 diesel difficult starting ok

CHECK INJECTOR LEAKAGE
COMMON FAULT WITH BOSCH INJECTORS

Posted on Feb 22, 2009

emissionwiz
  • 75814 Answers

SOURCE: PROGRAM KEYFOB FOR HYUNDAI SANTA FE

This is from the factory service manual of your car:
There is no onboard programming procedure for this vehicle. This vehicle requires special equipment be connected to the vehicle to program the keyless remote. Translation you need the dealer to do this.

Posted on May 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My problem in the type of car Santa Fe at 2007 3.3L examination give code p0174


Stuck with these codes P0174 and P0171..need help - Hyundai Forums ...

www.hyundai-forums.com/.../237193-stuck-these-codes-p0174-p0171-n...

Feb 12, 2014 - 10 posts - ‎6 authors
I've been getting these codes for awhile now which are p0174 "ECM has detected ... 06 Sonata LX 3.3L V6 ... the fact that your FE has gone down could indicate something else as .... 2014 Santa Fe Sport 2.0T AWD w/ Tech Package ... Join Date: Jul 2007 ...More on PowerTorque Tools - Hex Bits Set - SAE ...Missing: examination

p0171 p0172 p0174 p0175 p2187 p2188 p2189 p2190 - Page 2 - Hyundai ...

www.hyundai-forums.com/.../336641-p0171-p0172-p0174-p0175-p21...

Dec 25, 2014 - 10 posts - ‎3 authors
today one of my colleague who have same car sonata 2007 but with 4 cylinder.for checking ... Drives hyundai accent 2005(sold) Drives Hyundai Sonata 2006 v6 3.3L ...Due to it throwing codes for both rich and lean and after finding a thread searching those.... More on UltraSteel - Magnetic Nut Driver Set.Missing: examination

santa fe won't start, what is most likely wrong? - CarGurus


Jan 04, 2016 | Cars & Trucks

1 Answer

Hi All, I am driving 2007 Santa Fe 2.2 Diesel


Check all vacuum lines. Must be tight fit with no cracks. Cheap to replace.

Oct 29, 2013 | Hyundai Santa Fe Cars & Trucks

1 Answer

Cracking noise when turning corners with santa fe


Depending on which way you are turning The CV half shaft on the side making the noise needs to be replaced.

Jan 05, 2012 | 2007 Hyundai Santa Fe Limited

1 Answer

Looking to fit power chip. Where is diesel rail


on top of the injectors,alloy tube about 15" long

Jul 15, 2010 | 2007 Hyundai Santa Fe Limited

1 Answer

NO POWER ON COLD START UPS AND BLACK SMOKE COMING


are you letting the igniter heat up before starting it?

Apr 21, 2010 | 2007 Hyundai Santa Fe Limited

1 Answer

Electrical problem 2007 Hyundai Santa Fe 6 cyl All Wheel Drive Automatic 95000 miles Hyundai Sante Fe 2007 with 95,565 KM Cigarette lighter and power outlets dead All three outlets are gone dead 2 in the...


that can be 2 posibly..
1. check your batery still good or not
2. check your regulator (function is to recaharge batery when car is moving, if the regulator is not working replace it

Sep 10, 2009 | 2007 Hyundai Santa Fe Limited

1 Answer

Temparatur sensor


try autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you

Mar 19, 2009 | 2007 Hyundai Santa Fe Limited

Not finding what you are looking for?
2007 Hyundai Santa Fe Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...