Question about 2001 Ford Mustang

Open Question

2001 mustang . how do I find and repair the heater door blend actuator

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76691 Answers

SOURCE: Blend door not working.

The bleed door controls air temp not where it comes out, dash, floor, defroster, this is most likely a mode control switch problem, that switch is on the ac control head.

Posted on Sep 23, 2008

Ad
  • 1 Answer

SOURCE: Blend door

ok first put you front seat down and back raise steering wheel . now lay on you back with you head in the drivers floor board. look up see 2 screws remove them and the panel they hold on . look to left main wire harness needs to be moved to the right , up and behind it is th blend actuator 7/32 socket to remove it then manually turn the white peg , total labor 30 min

Posted on Dec 15, 2008

harley9701ha
  • 424 Answers

SOURCE: cant find the blend door actuator on 2003 ford f150 super crew

The temperature blend door actuator is located on the right side of the transmission hump under the evap. case. The floor ducts cover it.

Posted on Jun 22, 2009

  • 1 Answer

SOURCE: blend door actuator needs replacing does the

no it doesnt ... check out heatertreaters.net if you have to replace the blend doors .... but the actuator is directly behind the glove box...remove the glove box take out 3 screws and remove actuator and replace.....waa laa

Posted on Nov 25, 2009

  • 5 Answers

SOURCE: how to replace blend door actuator in a ford

I recently did mine, I hear you can do it without taking the entire dash apart but I had no luck with it myself. I have to get ready for work but, on mine it was located down and to the left of the radio. its a white box...are you hearing a clicking noise or something? I had to roll the entire dash back and it was still a major pain getting it out.

Posted on Dec 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I find the ac heat acuator on a 2001 Pontiac Bonneville sle.


How To Install Replace AC Heater Temperature Actuator ...

? 4:40
https://www.youtube.com/watch?v=mVP09M7hLB4
Jul 21, 2014 - Uploaded by 1A Auto Parts
http://www.1aauto.com/temperature-blend-door-actuator/i/1ahcx00293 ... How To Remove Install Door Chevy Monte Carlo Pontiac Grand Prix ...

GM Blend Door Actuator Repair (Saturn, Chevy, GMC, Buick ...

? 4:28
https://www.youtube.com/watch?v=fER3ZqnYLZg
Jul 11, 2014 - Uploaded by willmacneill
The procedure is the same for most GM blend door actuatorsfrom 1990-2013 (found in many vehicles made by Chevy, GMC, Buick, Pontiac, ...

Mode/Temperature Door Actuators May Fail : Pontiac ...




Jan 16, 2016 | Pontiac Cars & Trucks

1 Answer

99 expedition , how do you change actuater ?


1999 Ford Expedition Heater repair - Blend door actuator ...

? 1:53
https://www.youtube.com/watch?v=Yom1h8CCuzU
Oct 4, 2013 - Uploaded by shupe03a4
1999 Ford Expedition Heater repair - Blend door actuator I will post a ... Ford Expedition Heater Core ...

Nov 19, 2015 | Cars & Trucks

1 Answer

I have a 2001 chrysler voyager where is the blend door actuator located and how to remove it


its in the HVAC heater core box,
how to remove it is a very long answer.
read the FSM on HVAC
or login to alldata.com see HVAC chapter, and read. it.
anyone can, not just me.

i see this on line,.
  1. Disconnect and isolate the battery negative cable.
  2. Remove first row seat.
  3. Remove second row seat.
  4. Remove sliding door sill trim panel.
  5. Remove quarter trim bolster.
  6. Remove D-pillar trim panel.
  7. Remove first row seat belt anchor.
  8. Remove second row seat belt anchor.
  9. Remove screws attaching quarter trim to quarter panel from bolster area.
  10. Remove screws attaching rear edge of quarter trim to attaching bracket.
  11. Disengage hidden clips attaching front of quarter trim to quarter panel rearward of sliding door opening and at locators.
  12. Remove quarter trim from quarter panel.
  13. Disconnect speaker wire connector on LWB quarter trim panel with rear air conditioning.
  14. Pass second row seat belt through slot in trim panel on long wheel base vehicle.
  15. Pass first row seat belt through slot in trim panel.
  16. Remove quarter trim panel from vehicle.
  17. Remove the two screws that secure the top of the quarter trim panel attaching bracket to the quarter inner panel.
  18. Remove the screw that secures the back of the rear heater-A/C unit housing to the right D-pillar.
  19. Remove the screw that secures the front of the rear heater-A/C unit housing to the right quarter inner panel.
  20. Carefully pull the top of the rear heater-A/C unit housing away from the right quarter inner panel far enough to reach between the rear heater-A/C unit housing and the quarter inner panel to access the blend door actuator.
  21. Remove the two screws that secure the blend door actuator to the rear heater-A/C unit housing.
  22. Pull the blend door actuator away from the rear heater-A/C unit housing far enough to disengage the actuator output shaft from the blend air door pivot.
  23. Raise the blend door actuator far enough to access and disconnect the rear HVAC wire harness connector for the actuator from the actuator connector receptacle.
  24. Remove the blend door actuator from between the rear heater-A/C unit housing and the quarter inner panel.

May 21, 2014 | 2001 Chrysler Voyager

1 Answer

Blend door actuator failed ,how do i fix it?


The temperature blend door actuator itself is not repairable....it will have to be replaced. Its located under the center dash and is screwed to the heater box. I have included a picture of what it looks like.
2_14_2013_2_40_25_pm.jpg

Feb 14, 2013 | 2001 Ford F150 Styleside SuperCrew

1 Answer

Mi heater no calienta pero enfria mitsubishi montero 2001


Air Temperature Control Blend Door Failure No Heat or no AC (dependes on where door sticks)

In all modern cars there is a tiny DC electric motor driven gear drive that moves a plastic door that blends heated and cooled air from the AC and the heater core, this is called (interestedly enough) the air temperature control blend door actuator. The motor that moves this door fails because the door starts sticking from warping, most common complaint is no heat but it can be no AC as well. To replace these parts (blend door and blend door actuator) you must remove the entire dash from the car. Always have this problem confirmed by a dealer or qualified repair shop as it is a very expensive repair.

Other causes of no heat in the cabin are engine thermostats that are stuck open (engine runs cold) or air bubbles in the cooling system.

Nov 08, 2012 | Mitsubishi Cars & Trucks

1 Answer

Location of blend door on heater assembly on 2001 navigator


The blend air door is located INSIDE the A/C-heater housing assembly.
The blend air door is controlled by an electronic actuator. It could be that the actuator is malfunctioning. It is pretty easy to replace.

Since your Navigator is most likely equipped with automatic climate control, you may also have a problem with the interior temperature sensor. This could make it do what you are describing. Sometimes, a defective sun-load sensor can also cause this.

Then again, you may even have a broken blend air door (pretty common for Ford/Lincoln/Mercury products). If this is the case, the instrument panel must be removed to repair it. (HUGE JOB!)

I would recommend scanning your computer network to see if there are any HVAC fault codes before doing ANYTHING. There just might be a fault code to tell you what the problem is.

Jan 11, 2012 | 2001 Lincoln Navigator

1 Answer

2001 Ford Windstar, front and back heaters, back works fine front blows cold air


check the front blend door actuator if it is working.The actuator may be working but the blend door is broken stuck.remove the dash console panel [ac heater panel and radio] you can see the door actuator.remove the 3 screws and pullout the actuator using flat screwdriver try to rotate the door

Jan 08, 2010 | 1999 Ford Windstar

4 Answers

NO heat in front of 2001 windstar van. Thumping


Blend air door may be stuck. I removed a pencil from a heater box before. It had fallen from the dash, down through the defrost vents and jamed the door.

Nov 13, 2009 | 2001 Ford Windstar

1 Answer

No heat Heater core is hot


If heater core is getting coolant circulating through it then you may have a temp blend door, or blend door actuator not working properly. The blend door is located in the air box under the dash, and the actuator is located on the air box. You may be able to visually check the operation while turning the temp knob, by locating the coresponding actuator on the air box and monitoring the movement. If it is moving ok and still no heat then the blend door, or lever is broken, which will require removal of the dash.

Oct 17, 2009 | 2001 Dodge Ram 2500 Truck

Not finding what you are looking for?
2001 Ford Mustang Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...