Question about Toyota Cars & Trucks

1 Answer

I have a problem with my Toyota Aurion ZR6 2007. I couldnt lock/unlock with my smart key. I changed new battery but sometimes still working and sometimes doesnt. How can i fix this pro? Thanks all

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Take the vehicle to a dealership and have the key matched up to the remote module control in the vehicle. Takes 2 minutes and most dealerships / mechanics won't charge you. =)

Posted on Apr 03, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
ve3wtj
  • 147 Answers

SOURCE: 2004 Civic Drivers door lock

The driver's side door lock button is designed not to lock from the inside unless the handle is pulled, or the power switch is used. This serves as a reminder to not lock your keys inside.

If you are inside, and push down on the button (not the switch) hard enough to lock it, you've probably damaged it.

Posted on Sep 17, 2008

  • 199 Answers

SOURCE: need to locate toyota aurion/camry iac valve

the MAF sensor is between the air filter and throttle body. the idle controll is at the throttle body.  Its located on the throttle body on the left side. Follow the air intake to an intake manifold which sits on top of the throttle body. 

Posted on Jan 05, 2009

countrysi248
  • 443 Answers

SOURCE: 2000 Toyota Sienna Minivan car alarm goes off.

1. Start with key out of the ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Insert key into ignition (Do not turn) and pull it out.
3. Perform these steps within 40 seconds.
A. Using the power door lock switch on drivers door perform 5 lock/unlock cycles starting
with lock. Use an even pace and try to go about one cycle per second.
(1 cycle = 1 lock and 1 unlock.)
B. Close, then open drivers door.

4. Perform these steps within 40 seconds.
A. Using the power door lock switch on drivers door perform 5 lock/unlock cycles starting
with lock. Use an even pace and try to go about one cycle per second.
(1 cycle = 1 lock and 1 unlock.)
B. Insert the key in the ignition cylinder.
C. Turn the ignition to ON (Do NOT Start) then back to OFF.
D. Turn the ignition to ON (Do NOT Start) then back to OFF.
E. Remove the key from the ignition.

5. Within 3 seconds the power door locks should cycle automatically indicating successful entry
into programming mode. Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remote simultaneously for 1 second.
B. Immediately after letting go of the lock and unlock buttons,
Press the lock button by itself and hold for 2 seconds. Within 3 seconds the door locks
should cycle once indicating successful programming. If the door locks don't cycle or
cycle twice, repeat steps A and B, your remote has not been accepted.
C. Repeat steps A and B in step 6 for each new transmitter.

7. Close drivers door.

Posted on Apr 25, 2009

  • 1 Answer

SOURCE: My car key/remote lock and unlock stopped working.

happened to me once. the fuse for it was blown. $3 fuse replacement. check the fuse box & manual for this component. the fuse removal tool is located inside the engine fusebox area, and the fuse for the lock is inside the driver side box.

Posted on May 14, 2009

  • 166 Answers

SOURCE: key fob lights up but doesn't work even with a new battery

I'm more familiar with Range Rovers and Saab's when it comes to key fobs but if you changed the battery you have to re-program the key fob. If you do not have an owner's manual that can take you through the steps you might want to try: push and hold the lock button on the key fob, put it in the driver's side door and turn to lock. With the button still depressed turn back to open, remove the key and release the button. If this doesn't work check any and all fuses associated with your system and last but not least you could take it to a dealer. Good luck!

Posted on Aug 25, 2009

Testimonial: "thanks ill try what you've suggested"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2013 Toyota Highlander. Key fob remote doesn't work after installing new battery. It is not a smart key remote.


PROCEDURE. Make SURE the battery you installed is good.
  • Driver's door open, key removed from ignition switch
  • Within 5 seconds: Insert and remove the key from the ignition switch twice
  • Within 40 seconds: Close and open driver's door twice
  • Insert and remove the key from the ignition switch. Close and open driver's door twice
  • Insert the key into the ignition switch and close the driver's door
  • Within 40 seconds: Switch ignition ON and OFF once to program a remote transmitter code whilst retaining the original codes or twice to program and remote transmitter code whilst erasing the original codes. Three times to check how many remote transmitter are currently registered or five times to erase all registered codes
  • Remove key from ignition switch. System should now lock and unlock vehicle once, twice or five times depending which mode has been selected. One to four times, slowly, to indicate number of remote transmitters registered
  • Within 40 seconds: Press and hold LOCK and UNLOCK buttons simultaneously for 1.5 seconds
  • Within 3 seconds: Press LOCK button
  • SYstem should now lock and unlock vehicle once to confirm registration, twice to indicate registration has failed
  • Within 40 seconds: Repeat button procedure to program remaining remote transmitters.
  • NOTE: To exit programming mode: Open driver's dorr
  • NOTE: A maximum of 4 remote transmitters can be programmed
If the above programming procedures do not work, then you should contact your locksmith.

Goood Luck!

Dec 13, 2017 | Toyota Highlander Cars & Trucks

1 Answer

An 08 prius keyless entry doesn't work, changed the batteries, pushed the disable button and reset it, still no go. Any ideas?


1. Start with the key out of the ignition, drivers door is open all others closed and
drivers door is unlocked.
2. Perform these steps within 5 seconds.
A. Insert the key into the ignition and Pull key out twice (Do NOT Turn)


3. Perform these steps within 40 seconds.
A. Close then open the drivers door twice.
B. Insert the key into the ignition(Do NOT Turn) Pull key out.
4. Perform these steps within 40 seconds.
A. Close then open the drivers door twice.
B. Insert the key into ignition and leave it in ignition.
C. Close the drivers door.
D. Turn the ignition to ON (Do NOT Start) then back to OFF.
E. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should lock then unlock automatically
indicating successful entry into programming mode.
Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds.
B. Immediately after letting go of the lock and unlock buttons,
Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door
locks should lock and then unlock once indicating successful programming. If
the door locks cycle twice, repeat steps A and B in step 6 as the remote was
not accepted.
C. Repeat steps A and B in step 6 for each new remote.
7. Open drivers door.

Jul 17, 2014 | 2008 Toyota Prius

1 Answer

Peugeot 206 key fob


Try with brand new key fob battery and see.If that helps.
Otherwise May be keyfob needs to be reprogrammed.

KEYFOB PROGRAMMING


Keyfob remote reprogramming is not very difficult but on some cases it can be done by dealer service tools.

If the remote s faulty then key fob will not get programmed.

Insert the key in ignition. Turn the key to on position, and cycle the key three times off-on-off-on-off-on. Then with the key fob remote select your remote and then try to operate the vehicle with remote.

These are just the basic procedure, but sometimes it will not help.

On that case dealer is the only option.


---------

There are few much related troubleshooting links mentioned below for remote key fob reprogramming. I suggest you to go through the list and click the link below to go through its details and procedure: -------

2009 Toyota Highlander: Smart Key Not getting Detected?

http://whatisbyme.blogspot.in/2012/05/2009-toyota-highlander-smart-key-not.html


----------

2007 Toyota Prius: Reprogram Remote Keyfob?

http://whatisbyme.blogspot.in/2012/05/2007-toyota-prius-reprogram-remote.html

-----------

Pin that holds the flick key part to the key fob?

http://whoisbyme.blogspot.in/2012/07/pin-that-holds-flick-key-part-to-key-fob.html

-------------


2006 Toyota Hilux: Programming New Key?

http://technoanswers.blogspot.in/2012/04/2006-toyota-hilux-programming-new-key.html

----------

Where is Key chip memory located on 2004 ford Freestar?

http://technoanswers.blogspot.com/2012/01/where-is-key-chip-memory-located-on.html

----------

Ford Keyless Remote Fob Reprogramming?


http://schematicsdiagram.blogspot.com/2011/12/ford-keyless-remote-fob-reprogramming.html

----------

After getting car washed, check engine light is ON and key less entry not working, tried reprogramming. Also car shows fuel pressure?

http://schematicsdiagram.blogspot.com/2011/12/after-getting-car-washedcheck-engine.html

-----------

Audi A8 Key Fob Programming?


http://technoanswers.blogspot.com/2011/12/audi-a8-key-fob-programming.html

----------------

Oldsmobile Aurora Key Fob Reprogramming?

http://technoanswers.blogspot.com/2011/12/olds-aurora-key-fob-reprogramming.html

-------------

Buick Lesabre Key Fob Reprogramming?

http://technoanswers.blogspot.com/2011/12/buick-lesabre-key-fob-reprogramming.html

---------------

Keyfob remote not working on 2003 Ford E350 Econoline?

http://technoanswers.blogspot.in/2012/01/keyfob-remote-not-working-on-2003-ford.html

-----------

KeyFob will open the doors but not start on BMW?

http://technoanswers.blogspot.in/2012/02/key-will-open-doors-but-not-start-on.html

------------

Mitsubishi Car Key Not getting detected after replacing ECM

http://repairhelpcenter.blogspot.com/2012/11/mitsubishi-car-key-not-getting-detected.html

-----------

Key Fob will not lock and unlock doors?

http://technoanswers.blogspot.in/2012/02/key-fob-will-not-lock-and-unlock-doors.html

-------------

2000 Jeep Cherokee Limited: KeyFob Remote Not Working?

http://schematicsdiagram.blogspot.in/2012/06/2000-jeep-cherokee-limited-keyfob.html

-----------

Chevrolet Malibu: Key Stuck in ON position?

http://technoanswers.blogspot.in/2012/04/chevrolet-malibukey-stuck-in-on.html

-----------

Theft indicator not letting car to start?

http://technoanswers.blogspot.in/2012/02/theft-indicator-not-letting-car-to.html

-------------

2012 Dodge Ram: Ignition Key will not release?

http://whoisbyme.blogspot.in/2012/07/2012-dodge-ram-ignition-key-will-not.html

--------------


These details will help.

Thanks.

Nov 28, 2012 | Peugeot Cars & Trucks

1 Answer

Toyota matrix remote not unlocking car - battery is new


Check to see if your central locking still works on all doors and that you can also operate the driver's door central lock motor.
This can sometimes be an issue with the door lock motors themselves and not necessarily the key.

Nov 18, 2012 | 2005 Toyota Matrix

1 Answer

Remote got wet in salt water. Had battery changed


Programming
When
Key added or replaced. System malfunction.
How
Driver's door open and key removed from ignition switch. Insert key into ignition switch, then remove it. Within 5 seconds: Insert key into ignition switch, then remove it. Within 40 seconds: Close and open driver's door twice. Insert key into ignition switch, then remove it. Within 40 seconds: Close and open driver's door twice. Insert key into ignition switch. Close driver's door. Switch ignition ON and OFF once to program a new key code whilst retaining the original codes or twice to program a new key code whilst erasing the original codes. Remove key. System should now lock and unlock vehicle, once or twice depending which mode has been selected. Carry out the following button procedure within 40 seconds: Press key lock or unlock button once. Within 3 seconds: Press same key lock or unlock button once. System should now lock and unlock vehicle.
NOTE: If system locks and unlocks vehicle twice, programming procedure has not been completed. Repeat button procedure.
If required repeat button procedure to program remaining keys.
NOTE: To exit programming mode: Open driver's door. NOTE: A maximum of 4 keys can be programmed

This will work providing printed circuit is not damaged in remote

Jul 20, 2010 | 2004 Toyota Camry

1 Answer

Toyota corolla T3 will not lock/unlock from the key fob. Even tried the brand new spare key set which has never been used yet. Can use key to manually unlock and start car. Batteries seem to give a strong...


sounds like send/recieve signall out of sync.try locking car with key.hold lock button down on key for 30 secs.then unlock button for 30 secs.(point key at car from about 6 foot.)you do not need to sync all keys to car.hope this works.did for me.

Feb 17, 2010 | 2005 Toyota Corolla

1 Answer

Toyota avalon 2006 key fob apparently doesn't work


It looks like you have the "Smart Key" (a small rectangular box) that does not look like a traditional key.
What you also have is a dead battery inside the Smart Key.
Look closely at the box; there is a little button on the side. Press it. This will release a small hidden key. After you remove the small key, use a small flat blade screwdriver to pry the case of the box open at the slot provided. Take the unit to a store that sells miniature batteries, and have it replaced. You will NOT have to reprogram it after the battery is changed. The life span of the miniature batteries is roughly 20 months, less if exposed to RFI, like sitting on a TV, a monitor, or other electrical device. The Smart key TRANSMITS all of the time, even when you do not press the buttons. This is why the battery only lasts 18-20 months. Let me know if this fixes your issue..

Dec 16, 2008 | 2005 Toyota Avalon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

78257 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...