Question about 2000 Chrysler Cirrus

1 Answer

What does a shaft speed sencer do for a 2000 cirrus

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 954 Answers

According to Stratusphere.net, "Symptom: The car won't shift out of 1st gear. The 'Check Engine' light is on.

The speedometer doesn't work for this one. You're only able to go about 30 MPH without going above 4000 RPM.

Likely Cause #1: The Output Shaft Speed Sensor went bad.
Likely Solution #1: Replace the sensor (Part #4800879)."

The good news is that they are relatively cheap if you can install them yourself.

Posted on Apr 03, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 cirrus want change gears goes in drive and reverse inside on the dash where it tells you what gear you in all has squares around them speedometer doesn't work


Sounds like a speed sensor, I will look into that, but if the speedometer isn't working, its either cable, or electronic. Being a 2000, I'm guessing electronic. Chrysler have a lot of electronics on the transmission, as they are electronic themselves. I had an alternator go bad and my battery died, and the car wouldn't shift, it actually down shifted while driving. Have your battery and alternator checked first, then sensors. Like shift silinoid, speed sensor etc.

Apr 04, 2015 | 2000 Chrysler Cirrus

1 Answer

2000 silverado 1500 4.8 bank 1 and bank 2 to lean how can i fix


I have a 2001 Silverado 1500 with the 4.8 that had the same error codes. It turned out to be intake manifold gaskets were bad. With the engine running spray some carb cleaner on the intake where it bolts up to the heads and listen for the engine to speed up. If it does you've got a leak. With mine I couldn't find the leak with the carb cleaner but after I replaced the gaskets the problem was solved. Hope this helps.

Jan 18, 2012 | 2000 Chevrolet Silverado 1500

1 Answer

Cam shaft pos sencer code. replaced both sencers. still same code. wiring & plugs look good. car wont idle & stalls


Now you know that codes ,do not tell you what is wrong and what to replace
Get a diagnostic chart for your vehicle,and troubleshoot the area with issues.
TPS Sensor,Throttle Speed Sensor Etc, whatever applies to your vehicle

Apr 29, 2010 | 2002 Honda CR-V

2 Answers

2000 Chrysler Cirrus vibrates really bad at speeds under 40 km/h. Vibration still there at higher speed but not as bad. Steering and alignment don't appear to be affected. Any ideas?


Check the ball joints and tie rod ends and Tire balance. Could have broken/slpped bet in a tire or whaeel migh have thrown a balance weight.

Jan 15, 2010 | 2000 Chrysler Cirrus

1 Answer

2000 chrysler cirrus wont shift


it is going into limp mode. You need to take it to a trans shop to have diagnostic

Jul 06, 2009 | 2000 Chrysler Cirrus

1 Answer

How to change speed sensor for cirrus 2000


There should be 2 on the drivers side of the transmission. An input speed sensor 4800878 $21.95 and an output speed sensor 4800879 $21.95. These are easy to replace. First locate the 2 which should have a wiring harness attached to them, Second unhook the wires, Third unscrew them out individually as to not get them confused because they are different in shape just barely. Fourth screw in the new ones,Fifth replace the wires and you should be done.

Jan 13, 2009 | 2000 Chrysler Cirrus

1 Answer

Crank sensor location on 2000 Cirrus with 2.5 motor


hi ronco your crank shaft sensor should belocated in the front of ur motor on the crank pulley or it may be part of the damper pulley or behind it but it will be hard to see,... you will need to get under the car to c it but it will be right in that area torwards the bottom

Dec 24, 2008 | 1996 Chrysler Cirrus

1 Answer

Front and back speed senors


their should only be one speed sencer its in rearend on top of center housing most of the time its garbage getting on sencer its a magnetic sencer pickes up debre in fluid recomend fluid change when change sencer

Aug 01, 2008 | 2000 Ford Excursion

Not finding what you are looking for?
2000 Chrysler Cirrus Logo

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...