Question about 1999 Lincoln Town Car

1 Answer

99 Lincoln town car pulleys stop rotating What's the problem

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that got 5 achievements.


    Visited the website for 3 consecutive days.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 11 Answers

What pulley does not want to rotate. Is it the crank pulley. If it is, the lock key on your crank might have gotten damage due to the pulley that came loose or the vibration damper that is situated between your crank pulley broke loose and the part connected to the crank turns but the outer part of the pulley is not rotating.

Posted on Apr 03, 2015

  • stan flemmons Apr 03, 2015

    A/c and crankshaft pulley aren't rotating

  • stan flemmons Apr 03, 2015

    A/c and crankshaft pulley aren't rotating



6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 79186 Answers

SOURCE: 1999 lincoln town car fuel gage not working

99% of the time this is due to a defective gas gauge sending unit, this is located in the gas tank.

Posted on May 01, 2009

  • 1129 Answers

SOURCE: locatio of inertia switch 1990 lincoln town car

Check just above the carpet on the passenger side where your feet go under dash.

Posted on Jul 02, 2009

  • 14 Answers

SOURCE: 99 lincoln town car wont start?

make sure both plus amd minus turnimals are tight loss conection wont start the car you might get a clicking or just nothing

Posted on Oct 31, 2009

  • 17970 Answers

SOURCE: Where is the turn signal flasher lincoln town car

The Flasher is located: Front seating area, driver side, under dash, driver side of steering column, mounted on fuse side of fuse panel
Application: Turn signal and Hazard Lights

Have a nice day (remember comment and rated this help).

Posted on Mar 13, 2010

  • 24 Answers

SOURCE: Need a fuse box daigram and layout?

Pages 126-130

Posted on Apr 30, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

99 Lincoln Town to replace the driver's door on the town car?

All vehicles are pretty much the same with replacing a door. There will be bolts holding it on when you open the door, unplug the electrical and take off the bolts.

Nov 03, 2016 | 1999 Lincoln Town Car

1 Answer

Could a 99 Lincoln town car drivers door be exchange with a 98-00 Grand Marquis drivers door?

No they are not the same door, you would need a Crown Victoria door.

Oct 19, 2016 | Lincoln Cars & Trucks

1 Answer

Does a 99 lincoln have a knock sensor?

On both cars the knock sensor is located in the intake valley.
the computer receive signals if engine knocking and adjust the timing till stop.Before replace the sensors make sure the engine have no other misfire ,bad gas or vacuum leak.plug scan tool and read the code.Only circuit problem will be a true knock problem. Inspect all wire connectors before start taking a part.

Mar 28, 2014 | Lincoln Cars & Trucks

1 Answer

2001 lincoln town car belt routing

Continental And Mark VIII With The 4.6L Engine
Do not allow the drive belt tensioner to
snap back as damage to the drive belt tensioner or personal injury could result.

  1. Rotate the drive belt tensioner clockwise with a breaker bar installed in
    the 3?8
    inch square hole in the drive belt tensioner.
  2. Lift the drive belt over the idler pulley flange and remove the drive belt.
    To install:

  3. Following the schematic on the decal under the hood, position the belt over
    the pulleys, except the idler pulley.
  4. Rotate the tensioner as described above and install the belt on the idler.
    Ensure that all the V-grooves make proper contact with the pulleys.

Town Car With The 4.6L Engine

  1. Install a breaker bar in the 1?2 in. square hole in the automatic tensioner arm.
  2. Rotate the tensioner away from the belt with the breaker bar.
  3. Lift the old belt over the alternator pulley flange and remove it.
    To install:

  4. Position the new belt over all the pulleys, except the alternator pulley,
    rotate the tensioner as described above and install the belt on the alternator
    pulley. Refer to the belt routing illustration on the sticker located at the
    front of the engine compartment. Ensure that all the V-grooves and all the ribs
    on the belt properly contact the grooves on the pulleys.
  5. Rotate the tensioner toward the belt and remove the breaker bar.

    Fig. 1: Make sure the belt makes proper contact with the pulley

    Fig. 2: Accessory drive belt routing - 4.6L engine

Town Car And Mark VII With The 5.0L Engine

Sep 23, 2010 | 2001 Lincoln Town Car

2 Answers

Where is the number 1 piston located on a 99 lincoln towncar?

Standing in front of crankshaft pulley, it's your left side, closest to you. (left front)

Nov 15, 2009 | 1999 Lincoln Town Car

Not finding what you are looking for?
1999 Lincoln Town Car Logo

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts


Level 3 Expert

79186 Answers


Level 3 Expert

5677 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides