Question about Ford Ranger
I AM PUTTING A AIR CONDITIONER ON MY TRICK ,BUT I CAN'T FIND A DIAGAM ANY WHERE
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: ignition wiring
1991-1994 2.9L and 3.0L Engines Firing Order 1-4-2-5-3-6
1995 And Later 3.0L V-6 With DIS Ignition System Firing Order 1-4-2-5-3-6
4.0L Engines Firing Order: 1-4-2-5-3-6 DIS Ignition System
Posted on Nov 23, 2008
Save your money, the chip is a ohm resistor at Radio Shack for under $2.00. It splices in to you IAT wire harness located at the intake tube between the air filter housing and throttle body.
Problem with this system is, that you can not adjust anything and have to run a constant 91 octane just to make sure you do not have a Detonation. The ECM will catch the Detonation from the knock sensor and compensate for it by retarding the timing which in turn lose of HP till next start up.
If you like and don't mind the check engine light on once and awhile, you can do the same by just disconnecting the IAT wire harness which give the ECM a 0 resistance thinking it's -20 out side and turn the timing up and lengths the injector pules.
When i was running a Nitro in the Toy before i sold it, i had installed a 10K ohm Potentiometer which you can buy at radio shack for under $5.00 i believe, I just spliced it in to the IAC wire harness so if i wanted to play with the Nitro I'ld turn the resistor up making the engine think it's 185 degrees F and would ****** the timing so i would not hurt the engine. But if i wanted to get more timing i would just turn the knob to drop the resistance to get more time since the engine thinks it's -20 out side.
Hope this helps. Keep me posted if you need more info. Best thing is to do a dyno tune and you can change everything right down to the Shift points.
Posted on May 29, 2009
Copy and paste this into your search window: 2002 ford ranger rear brake diagram
You should see four pictures pop up, select the brake parts diagram or the brake picture.
Posted on Sep 03, 2009
RANGER FUSE PANEL
On Board Diagnostic (OBD) II System
Air Bag System/Blower Relay
Right Headlamp/Fog Lamp System
Speed Control/GEM System/Brake Interlock
Front Washer System
4WD/ABS/Speed Control 14 10/20 Amp ABS System 15 7.5 Amp Air Bag System/Alternator 16 30 Amp Front Wiper 17 15 Amp Cigar Lighter 18 15 Amp A/C System 19 25 Amp Ignition Coil/PCM System 20 7.5 Amp Radio/GEM System/Anti-Theft 21 15 Amp Hazard Lamps 22 10 Amp Turn Signals 23 — Not Used 24 10 Amp Starter Relay/Anti-Theft 25 7.5 Amp Speedometer/GEM System 26 10 Amp 4R44E/4R55E Trans./Backup Lamps/DRL System 27 10 Amp Underhood LP/Map Lights/Glove Box Lamp/Dome Lamp/Visor Lamps/4x4 Sys. 28 7.5 Amp GEM System 29 10 Amp Audio System 30 — Not Used 31 — Not Used 32 — Not Used 33 15 Amp High Beam Lamps 34 — Not Used
Posted on Mar 14, 2010
Tips for a great answer:
Oct 08, 2016 | Ford Cars & Trucks
Nov 25, 2014 | 1992 Ford Ranger
Nov 25, 2014 | 1992 Ford Ranger
Sep 09, 2014 | Ford Cars & Trucks
Mar 18, 2012 | 1991 Ford Ranger Supercab
Sep 12, 2011 | 1996 Ford Ranger SuperCab
Nov 01, 2009 | 1996 Ford Ranger SuperCab
Oct 21, 2009 | 1995 Ford Ranger Supercab
Sep 29, 2009 | 1996 Ford Ranger SuperCab
Aug 12, 2009 | 1996 Ford Ranger SuperCab
Sep 25, 2017 | Ford Cars & Trucks
26 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: