Question about 1999 Dodge Durango

1 Answer

What do I have to do to change the oil pump on a 1999 dodge durango

Do I have to loosen a motor mount

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 602 Answers

Remove the oil pan, you may have to pull the engine to get the pan off.

Posted on Apr 03, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have to replace fan resister on my 2000 pontiac Montana do I to take out the blower motor to get at the resister


Step 1: Pry and remove the retaining pins (3) that secure the interior panel to the UNDERSIDE of the glove compartment area (near the PASSENGER'S feet).

Step 2: Disconnect the blower motor's wiring harness (1).

Step 3: Loosen and remove the 7/32 mounting bolts (3) that secure the blower motor to the vehicle. Pull the blower motor from the vehicle.

Step 4: Disconnect the wiring harness (1) mounted just to the LEFT of the resistor.

Step 5: Loosen and remove the 7/32 mounting bolts (3) that secure the resistor to the vehicle.


NOTE: You only need to LOOSEN the rear bolts, as the resistor will slide free without completely removing them!

Step 6: You can now slide and remove the resistor.

Step 7: Mount the new resistor by tightening the 7/32 mounting bolts (3). Connect the wiring harness (1).

Step 8: Reattach the blower motor by tightening the 7/32 mounting bolts (3).

Step 9: Connect the blower motor's wiring harness (1).

Step 10: Re-engage the retaining pins (3) to secure the interior panel to the UNDERSIDE of the glove compartment area.

Nov 12, 2016 | Pontiac Cars & Trucks

1 Answer

How do I install the alternator on a 2003 KIA Spectra?


I just replaced the alternator on my 2003 Kia Spectra, not an easy job. It has to be removed from under the vehicle. First, after disconnecting the battery, remove the "locking" bolt on the topside of the alternator, along with the adjusting bolt (both metric 12mm). This is done from the topside, (rear, right side of the engine compartment). From under the vehicle, loosen the bolt that holds the alternator. At this point you have to decide whether to loosen the exhaust manifold or motor mount. I choose the motor mount. I loosened the mount and used a floor jack to raise the engine, only needed about an inch. Good luck.

Oct 10, 2014 | 2003 Kia Spectra

1 Answer

How to replace the motor blower resistor on a 1999 dodge durango


Follow wires back from blower motor , they should be plugged in to resistor. Usually mounted on duct work below on passenger side.

May 03, 2014 | 1999 Dodge Durango

1 Answer

Wheres the oil pump


The oil pump will be in the oil pan bolted to the motor. You must remove the oil pan to access it. In some vehicles you may have to loosen the motor mounts and lift the engine up a little to remove the oil pan.

Mar 31, 2014 | 1999 Ford Explorer

1 Answer

Motor mount proceedure


Are you looking to replace the motor mount? If so I suggest loosen the mounts, hold the engine up via a hoist, take out 1 mount and the other 1 will hold it in place acting like a hinge. Bolt the new mount in place. Once that side is done do the same for the other side.

Dec 06, 2013 | 1994 Chevrolet Camaro

1 Answer

Nissan terrano 1996 2.7 diesel


The sensor is located behind the crank pulley/harmonic dampener. To replace:

1 Remove the tire/wheel and splash shield.
2 Remove the bolts, then loosen the mount bolt and pivot the side engine mount out of the way.
3 Loosen the idler pulley center nut and adjusting bolt, then remove the A/C compressor belt.
4 Loosen the alternator mounting bolt, nut and adjusting bolt, then remove the alternator belt.
5 Loosen the mounting nuts and adjusting nut, then remove the P/S pump belt.
6 Remove the dipstick and pipe.
7 Remove the crankshaft pulley.
8 Remove the upper covers and lower cover. NOTE: Do not use the upper and lower covers for storing removed items.
9 Remove the CKP sensor from the cylinder block.
10 Install the CKP sensor in reverse order of removal.

Feb 23, 2013 | Cars & Trucks

1 Answer

Where are the motor mount bolts


Your under the car working on the starter

You look at the mounts,they have to have at least 2 or 3
bolts holding them to the sub frame,you don't remove the
engine side of mount !!!

Dec 09, 2012 | 2002 Dodge Intrepid

1 Answer

How do I loosen main nut to remove fan from water pump on a 1999 Dodge Durango with V8 engine?


I have same truck but an 02 antway you need to rent a special wrench you can get it at autozone.

Sep 03, 2012 | 1999 Dodge Durango

1 Answer

Best way change oil pump in 1999 dodge durango


You have to remove the oil pan. It is different for 2wheel drive and 4 wheel drive. In either case, you have to jack up and support the engine. Most of the time you must also remove the transmission rear mount so you can jack up the transmission also in order to get enough clearance to get the pan out between the transmission bell housing and the frame crossmember.

On 4X4 vehicles, you must also first remove the skid plates and the front drive axle to get the oil pan off.

Dec 13, 2010 | 1999 Dodge Durango

1 Answer

Whats the best way to get to the oil pressure sending unit on a 5.9 litre dodge ram


The oil pressure "sending unit" pump is located in the oil pan, in/at the bottom of the engine. It's not something I'd recommend trying if you've never attempted a lengthy or relatively difficult repair, without guidance. You don't indicate if you have 2wd of 4wd. However, in any event, you're going to have to remove the oil pan. It will most likely require you to loosen the motor mount(s) and jack/lift up the engine. Not necessarily the best way, but the easiest. I'd be concerned with engine wear also if the oil pump is bad. Which would require you to at least change the connecting rod and main bearings.

Mar 05, 2010 | 1999 Dodge Ram

Not finding what you are looking for?
1999 Dodge Durango Logo

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...