Question about 2002 Peugeot 307

2 Answers

How do i fix the car when it keeps flashing economic mode active

I had at first changed the battery, and now the car can't start, the key has lost memory, the driver's window can't close, also the central lock system is working, i have bought a new coil, but the car can't start but cranks only, please give me tips

Posted by Anonymous on

  • Paul Woodward Sep 04, 2015

    it goes into economy mode when battery is low and stops use of various internal electrics. make sure battery is charged and see my answer below

×

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 136 Answers

When u change car battery or keyfobs battery u have to reprogramme the key fob. u do this as follows:
switch off and take key out
insert key and switch on, do not turn over but allow the the display to run thru its 5 sec displays
switch off, wait a few secs then when u turn ignition on hold down lock button for 10 secs immediately after turning on. do not at any point turn engine over!!

switch off and take key out of ignition. should now be reset so insert, pray wait for display to do its thing and turn over

this instruction is in manual and worked for me after changing keyfob batery - the penny round 2016 size!

Posted on Sep 04, 2015

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 361 Answers

Look on youtube you will get your answer there

Posted on Apr 21, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

SOURCE: peugeot 406 central locking

you need to reprogram the fob

Posted on Oct 07, 2008

  • 215 Answers

SOURCE: 307 central locking fault

If you have replaced the battery and the ecu wasn't in sleep mode, then you'll lose the synchronisation between immobiliser and fob. go to peugeot dealer or call out a car locksmith who then can reprogram your fob with car ecu. I have read the method in internet but not sure what the steps were. you can google it may be you'll find it.

Posted on Sep 05, 2009

dancandoit
  • 436 Answers

SOURCE: alarm not opening drivers door only.

the motor in the drivers door has packed up, you will need to replace this for it to work properly.

Posted on Mar 05, 2010

  • 1 Answer

SOURCE: Central Locking Issues on Peugeot 406 exec 2.2 hdi (2002)

Hi,just reading with interest" Ianhende's" problem with his 406, I have the same sort of problem with a 2002 406 hdi (110) i.e hazards going off,plus central locking turning on & off whilst driving. have replaced battery, the mechanic is thinking that it is to do with a faulty door lock, any ideas out there ???? ajc.jlc@tiscali.co.uk

Posted on Apr 22, 2010

  • 2 Answers

SOURCE: hi my central locking system is completely not working on 206 1.1 v reg,only lights when press remote,can't lock the boot now,what is the fault?

Ceck the relays in the fues box it could be the problem ?

Posted on Apr 03, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2007 golf r32 last weekend the car started and then immediately stopped with immobiliser active reading on the dashboard the battery is fully charged and both keys have new batteries.


Sounds like the tiny transponder in your keys has failed.or dropped.out while your changed /checked batteries. Small glass bead about 2mm diameter and 8mm long. Check where you drooped it ?
Or reset the keys. Driver door open, Key in the ignition, and press.and hold all buttons u.til tiny red light on keys ( pin hole youve probably not noticed before) lights up and flashed to pair after 5seconds press open door. Then close and open again keep driver door open. Repeat with second keys.
Should fix it.

Jun 11, 2017 | Cars & Trucks

1 Answer

Battery changed in key fob now will not start


You have lost programming, contact your local dealer.

Jan 18, 2017 | Cars & Trucks

2 Answers

How do you turn off an alarm for a 2005 Saturn Ion


Disarming an Armed System/Silencing an Alarm
If system arming has been requested by the keyless entry transmitter, it must be disarmed.
Important: Using the power door unlock switch or manually unlocking the doors does not disable the CTD armed mode. Also, disconnecting the battery or pulling fuses does not disable the armed mode, since the BCM stores the CTD mode status in memory.
?€¢
To disarm the CTD system in arm pending mode, SECURITY indicator flashing and doors open, perform 1 of the following:


-
Press the UNLOCK button on the keyless entry transmitter.


-
Insert a valid key into the ignition and start the vehicle.


?€¢
To disarm the CTD system in the armed mode:


-
Press the UNLOCK button on the keyless entry transmitter.


-
Insert a valid key into the ignition and start the vehicle.


?€¢
To disarm the CTD system when activated, alarming mode.


-
Press the UNLOCK button on the keyless entry transmitter.


-
Insert a valid key into the ignition and start the vehicle.

Jun 24, 2016 | 2005 Saturn ION

1 Answer

I lost my key to my 1996 firebird. so i had the ignition changed out. at the same time my battery went dead. i put a new battery in and the car wont start all lights come on just wont turn on. the...


Your ignition takes a specific key, they are chipped. If the ignition was changed and the decoder wasn't , this is the problem. You may be able to call a dealer ship and give the VIN number and get the measurement in ohms of the chip, Maybe. Then go to a hard ware store and they can duplicate the key you have with a chip key. Be prepared , this is not a $2.00 key

Sep 02, 2011 | 2003 Pontiac Grand Am

1 Answer

I have a 1997 infiniti I30, one day all of a sudden when I came out of a grocery store I turned the key and absoloutely nothing happened. My lights can come on inside the car but, my power windows wont...


This is from Ken on CarPros:
Here is the way to reset the security system.

https://www.2carpros.com/articles/how-to-reset-a-security-system

Here is the systems descriptions

There are 2 security system, namely anti-theft and immobilizer.

Here are the 2 systems.

DESCRIPTION & OPERATION
Anti-theft system is controlled by Body Control Module (BCM). BCM receives signals from hood switch, trunk switch, door switches and Local Control Modules (LCMs). There are 5 LCMs located throughout vehicle.

To set anti-theft system in armed mode, remove ignition key, close all doors, trunk and hood. Lock doors using key or remote controller. The SECURITY light will illuminate for 30 seconds, then flash in 2.4 second intervals, indicating system is in armed mode.

To cancel armed mode, unlock and open any door or trunk lid using key or remote controller. SECURITY light will flash every second, indicating system is disarmed.

Alarm will activate (horn sounds, headlights flash and starter circuit is disabled) if any of the following conditions occur while system is in armed mode:

Engine hood or trunk lid is opened using the hood or trunk lid release.
Door(s) is unlocked without key or remote controller.
Tampering with any door/trunk lid key cylinders.
To deactivate anti-theft system, unlock door or trunk using key or remote controller.

If it is the immobilizer that is preventing the engine from being started, ensure you have the correct key and the transponder is intact. Quite often keys are dropped and if it breaks open, the internals would scatter all over. When this occurs, there is a tendency for the transponder to be lost.

Please let us know happens so it will help others.

Best, Ken
I hope that helps you out!

Mar 31, 2017 | 1997 Infiniti.5 J30

1 Answer

Just bought a x reg ford puma but the key fob does not work, bought a new battery and fitted it, needs re-programming but don't know how to do it.


Telephone: Fax: VAT Registration No.:
Infrared remote control
NOTE: Infrared emitter can be seen at front edge of key.
System operation
Switch ignition ON. Ensure clock LED illuminates for 3-5 seconds. Pressing key lock button once activates central locking and alarm. Pressing key lock button twice within 3 seconds activates double locking system.
Programming
When
Key batteries completely discharged. Key batteries not replaced within 15 seconds. Key added or replaced. System malfunction.
How
Obtain all keys fitted with remote control. Turn ignition switch to position I. Wait approximately 10 seconds. Ensure clock LED illuminates.
NOTE: LED illuminates for approximately 5 seconds.
Switch ignition OFF and remove key, while LED illuminated. Programming mode activated for approximately 20 seconds (LED illuminated). Proceed as follows: Point key at receiver (located near interior lamp). Press and hold unlock button Fig. 1 [1]. After approximately 1 second key LED will flash once [3]. Press lock button 3 times Fig. 1 [2]. Release unlock button Fig. 1 [1]. Continue to point key at receiver until LEDs in clock and key have flashed 5 times. Ensure LED remains illuminated. Repeat above procedure within 20 seconds to program remaining keys. To exit programming mode and extinguish clock LED: Switch ignition ON and OFF. Wait approximately 20 seconds.
NOTE: A maximum of 4 keys can be programmed. Fig. 1
Radio frequency remote control
System operation
Switch ignition ON. Ensure clock LED illuminates for 3-5 seconds.


Pressing tailgate release button twice within 3 seconds unlocks the tailgate - if fitted. Pressing key lock button once activates central locking and alarm. Pressing key lock button twice within 3 seconds activates double locking system. Interior lamp illuminates when disarming system.
Programming
When
Key added or replaced. System malfunction.
How
Obtain all keys fitted with remote control. Fasten seat belts and close all doors. From position I, turn ignition switch as follows: To position II. To position I. To position II. To position I. To position II. To position I. Programming mode activated for approximately 20 seconds. LED or fog lamps ON warning lamp illuminates (some models) or the system will emit an acoustic signal to indicate start of programming mode. Proceed as follows: Type 1: Press and hold unlock button Fig. 1 [1]. Type 2: Press unlock button Fig. 2 [2]. Ensure clock LED or fog lamps ON warning lamp flashes (some models) or wait for acoustic signal (indicates correct programming). Wait 2 seconds. Repeat above procedure within 20 seconds to program remaining keys. To exit programming mode: Switch ignition ON. Wait 20 seconds.
NOTE: A maximum of 4 keys can be programmed.

Aug 25, 2010 | Ford Focus Cars & Trucks

3 Answers

Reset immobiliser


u must put a key to ignition and open a drive door 3 times and press and hold lock button

Jan 18, 2010 | 2007 Ford F

1 Answer

I have just changed the batteries in my key fob for my P reg. ford fiesta but it won't open the doors


Programming
When
Key batteries completely discharged. Key batteries not replaced within 15 seconds. Key added or replaced. System malfunction.
How
Obtain all keys fitted with remote control. Turn ignition switch to position I. Wait approximately 10 seconds. Ensure clock LED illuminates.
NOTE: LED illuminates for approximately 5 seconds.
Switch ignition OFF and remove key, while LED illuminated. Programming mode activated for approximately 20 seconds (LED illuminated). Proceed as follows: Point key at receiver (located near interior lamp). Press and hold unlock button Fig. 1 [1]. After approximately 1 second key LED will flash once [3]. Press lock button 3-5 times Fig. 1 [2]. Release unlock button Fig. 1 [1]. Continue to point key at receiver until LEDs in clock and key have flashed 5 times. Repeat above procedure within 20 seconds to program remaining keys. To exit programming mode and extinguish clock LED: Switch ignition ON and OFF. Wait approximately 20 seconds

Jan 16, 2010 | 1995 Ford Escort

1 Answer

I bought a new Keyless remote for a 2007 Forester from a Subaru Dealer to replace an original one that went bad after 2 years. I have followed the directions in the owner's manual to program it, but can't...


IMPREZA: 2005, 2006, 2007 and
FORESTER: 2005, 2006, 2007, 2008
Check for Immobilizer key on Forester XT models only.
information is always subject to change and correction imp05keylessremote1.jpg
new remote for 2005 Imprezas.
This is not the same remote as the 05 Legacy/Outback remote which also has truck/gate release on the front and a red panic button on the back.
Lock: press Lock button for 2 seconds or so to lock car, and arm optional security system. The car with chirp once and turn signals flash for locked, 5 short chirps and signal flashes if any door is not fully closed. The dome light goes on for 15 seconds and ignition key ring (if present) will light for 30 seconds when unlocked.
Unlock: press unlock one time for driver's door, press again within 5 seconds to unlock all doors inkling rear gate (wagon). The system does not open the trunk.
Panic mode: press and hold lock button for approx. 3-4 seconds to activate Panic mode. I panic model the horn honks and turn signals flash until either the lock or unlock button is pushed again.
Finder mode: Press lock button 3 times within 5 seconds to activate Vehicle Finder mode. The horn will honk once and the turn signals will flash 3 times
Distance: works within approx. 30 feet depending on battery strength, nearby concrete walls and etc.
Audible Chirp On-Off: the system will chirp when locked or unlocked. To turn OFF the chirps, unlock the door and then push both lock and unlock buttons at the exact same time for 2+ seconds. There will be 2 chirps indicating the the audible is off. To turn the chirp back on, repeat the process and the system will chirp one time when it is back on.
Battery: as the battery ages it will only work as you get closer to the car. When a battery is replaced, the transmitter must be re-synchronized with the Keyless control unit. To synchronize, press the lock or unlock button 6 times.
Programming: 4 codes may be programmed.
Sit in driver's seat and unlock all doors. Open and close the driver's door
Turn the ignition key from LOCK to ON position 10 times within 15 seconds. Be sure to stop at both lock and on. The horn will HONK once to indicate transmitter programming mode is activated. Leave key in LOCK position and don't remove it from ignition.
You now have 45 seconds to complete the programming as below.
Open and close driver's door again.
Push either lock or unlock button on the remote you want to program. The horn will honk 2 times when successful.
To continue and program other remotes at the same time: open and close the driver's door and push lock or unlock on the remote. The driver's door must be opened and closed between each remote you want to program.
Done programming? remove the key from the ignition and the horn will honk 3 times.
DELETE old codes? Reprogram 4 times, it will overwrite old codes.
Alarm Security System: optional on all models. When locked there is one chirp (can be turned off, see above), the turn signals will flash and the red 'security' light will start to flash once every 2 seconds except for STi which flashes twice every 2 seconds.
There will be 5 chirps if a door, hood, and trunk or gate is not fully closed
You can also arm the system by using the power lock button on the driver or passenger door as you get out of the car and then closing the door behind you.
Disarm the system: push unlock for 2 seconds
Lost remote, alarm activated? When you can't use a remote to turn off the system: open the door with a key or try to start the car and the horn will start to honk. Turn the key on-off 3 times within 5 seconds and the alarm will go off and you can start the car. It's simple!
VALET mode: To set valet mode or just to disable the security alarm system: 1. unlock all doors 2. physically open the driver's door 3. hold the UNLOCK button on remote for 2+ seconds. The red 'security' light will then flash 2 times a second until the car is turned on.
System has been Tripped (except for STi): if you unlock the door with the remote and it chirps the signal light flash 4 times, the system has been triggered;
Identification mode: To find out what happened and why the system was triggered:
Open and drivers door, leave it open. Turn ignition key from LOCK to ON 2 times and then leave in LOCK position.
Tripped code: 1 security light flash: a door has been opened, 3 flashes when the impact sensor was triggered, 4 flashes when the ignition was messed with or battery disconnected

Nov 19, 2009 | 2007 Subaru Forester 2.5X L.L. Bean...

1 Answer

Keyless entry keylob want lock or unlock doors or trunk.change battery and checked all fuses.


You need to program the remote. Get in to the car and LOCK all doors with the switch on drivers side door. Take the key and insert it into the ignition cylinder in and out 6-10 times, until the flashers/hazards flash on your dash board. Or just keep putting the key in and out (nice and easy now, not fast) until you see the lights on dash flash. After the lights flash, turn the key into ACC mode to make the whole dash light up.(do not start car) .With the key in ACC position, hit any button on remote, that will make the hazards flash again. Turn key off and unlock door with switch again. Open door.DONE.
Good luck.

Jul 15, 2008 | 2001 Nissan Altima

Not finding what you are looking for?
2002 Peugeot 307 Logo

201 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

mike hayward

Level 2 Expert

279 Answers

Wahs Team

Level 2 Expert

215 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...