Question about 2000 Mazda MPV

Open Question

How Much Torque / Foot-pounds Should I use To Tighten The oil Pan on a 2000 Mazda Mpv Lx ?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: replace an oil pan and casket

Thanks, the problem has been answered.

I've also submitted my comment

Posted on Jul 02, 2008

Ad
  • 1 Answer

SOURCE: 2000 Mazda MPV Heating problem

The heater lines that run to the back of the right rear side gets rusty and start to leak anti-freeze. There is a black cover under and above the RR tire that has to be removed so u can see.

Posted on Feb 09, 2009

  • 6 Answers

SOURCE: Mazda MPV LX 2000

Yes, that was too much. The neutral safety switch costs around $70 (if I remembered right). I bought it from my Mazda dealer and asked them for a diagram to locate it. In most cases, my Mazda dealer has been helpful in provide diagrams for this minivan. The switch is located underneath the battery (you'll have to remove it) on the transmission. Make sure it is aligned right when you replace the switch; otherwise it won't find neutral, and you'll have to use the bypass switch on top of the steering column to start you engine.

Posted on May 04, 2009

emissionwiz
  • 76846 Answers

SOURCE: Where is the bank 2 o2 sensor located on a 2004

bank 2 is the cylinder in the front of the engine compartment near the radiator, the O2 is either in the exhaust manifold of the bank or in the exhaust pipe off the manifold, round about the size of a jumbo magic marker, you need a special O2 sensor socket to remove it in some cases, if it is in the open then a 7/8 open end wrench will work.

Posted on Oct 09, 2009

Testimonial: "Awesome response time, this was exactly the information I needed."

  • 10 Answers

SOURCE: how do I replace alternator in mazda mpv 2000?

Typically an alternator is an easy fix. It requires removal of the belt from the engine running it, and a few bolts that attach it to the engine.

Because of the engineering with the 2000 mpv, it is a very difficult fix, and one that requires removal of the transaxle and exhaust manifold, as well as removal of the lower engine mounts. It will take a qualified Mazda mechanic 3.5 hours to do the fix - you can (at least) triple that amount of time as a DIY project (assuming you have the right tools).

Posted on Nov 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the right oil and filter to use on the range2007 hse?


How To Change Oil and Oil Filter on Range Rover Sport or Land Rover LR3

  • Place an oil drain pan below the oil filter and drain plug and unscrew the oil filter.
  • Lubricate the rubber seal with clean oil and install the new filter. Tighten to 13 foot-pound torque.
  • Remove drain plug in the oil pan and drain the oil. Catch the oil in the drain pan. After draining the oil install and tighten the drain plug to 18 foot-pound torque.
  • Fill engine with 5W-30 weight oil. The 4.4 V8 takes 8 quarts; the 4.0 V6 takes 6 quarts. Start engine and check for leaks.
  • Recheck level and top up as necessary.
  • Reinstall the under engine shields / skid plates.

Apr 12, 2015 | Land Rover Range Rover Cars & Trucks

2 Answers

What are the torque specifications for the transmission pan


Tighten the oil pan to transmission case bolts alternately and evenly to 11 N·m (97 lb in) notice not foot lbs. hope this helps

Aug 02, 2014 | 2006 Chevrolet Trailblazer

1 Answer

Where is the oil drain plug on a 2002 BMW 325i


It is located on the oil pan, please be advised the oil pan is also the casting that houses the front differential, and the engine oil drain is the hex nut furthest to the rear of of the pan . You will need a 17mm wrench to remove the hex nut . After you drain the oil, DO NOT over tighten the plug . The proper torque is 25 newton/meters or about 20 foot/pounds

Sep 12, 2012 | 2002 BMW 5 Series

1 Answer

Cyl head torque specs focus 1.6 LX 07


cylinder head and main bearing bolts had a first step torque of 50 to 60 foot-pounds and a second step torque of 80 to 90 foot-pounds each. The rod bearing bolts had a first step torque of 25 to 30 foot-pounds and a second step torque of 30 to 36 foot-pounds. The intake manifold and exhaust had a first step torque of 5 to 7 foot-pounds. The intake manifold had a second step torque of 14 to 21 foot-pounds while the exhaust manifold had a second step torque of 16 to 23 foot-pounds.

BMW PARTS

May 25, 2012 | Ford Focus Cars & Trucks

2 Answers

2001 daewoo lanos dual overhead 1.6 liter head bolt torque and sequence


  1. Tighten cylinder head bolts to 25 N.m (18 ft. lbs.). Tighten bolts an additional 70 degrees plus 70 degrees plus 30 degrees using angular torque gauge .
2001-daewoo-lanos-dual-overhead-1-6-vrq3bch1e30nz1jlq5sn5nnt-4-0.gif

Oct 20, 2011 | 2000 Daewoo Lanos

1 Answer

Conversion kgf.m to foot pounds.


1 kilogram meter = 7.233 013 831 6 pound foot

you can use a online converter like the http://www.onlineconversion.com/torque.htm

3.5 kilogram meter = 25.315 548 411 pound foot
4.5 kilogram meter = 32.548 562 242 pound foot

Jan 28, 2010 | 2006 Hyundai Santa Fe

1 Answer

2008 chevy 2500 HD w/ Allison


Hello. torque pan bolts to 7-10 foot pounds, install the drain plug and tighten to 25 foot pounds.
Regards, Joe

Nov 18, 2009 | 2008 Chevrolet Silverado 2500HD 2WD

1 Answer

How do I change oil on a 2004 Mazda MPV


the plug is directly behind engine, on bottom of oil pan. take a 16mm to remove. just did my oil in 2004 MVP LX so I know its there unless for some odd reason they made your oil pan and forgot to but the plug in it.

Apr 03, 2009 | 2004 Mazda MPV

1 Answer

Help me with removing my oil pan


I highly recommend having a torque wrench at your disposal to perform this procedure. Hondas go forever if you take care of them, a torque wrench is a small investment (and some auto parts stores will loan/rent them to you).

According to the manual (for the 1998 - the 1996 is probably the same) you will first need to remove the transmissioin/engine stiffener. This is a piece that transverses from the engine to transmission and is held in place by 4 bolts.

After that you remove the existing oil pan.

You must scrape off any residue or remaining gasket from the engine block - you can do that with a putty knife. Be careful not to scratch/gouge the surface. Then clean the surface of the engine block.

Get a new pan and gasket. Use gasket seal (Honda part # 08718-0001 ir 0718-0003) to afix the gasket to the pan. According to the manual, after affixing the gasket you should use additional gasket seal at both of the short ends of the (more or less) rectangular outline of the pan/gasket (including the rounded corners) and then put them on to the block (do this within 5 minutes of applying the gasket seal). The manual indicates you should hand tighten six bolts - the ones at the corners of the short ends of the rectangle, and the ones right in the middle of the long ends. When these are hand tight you will insert and hand tighten the other bolts. Then increasingly tighten the bolts starting with the one most directly under the oil filter. Work from that bolt clockwise, gradually increasing the tightness of the bolts until you reach a torque of 8.7 foot pounds.

If you don't do this correctly you will warp the pan, so be careful.

Once completed you should refasten the engine stiffener. The bolts going to the engine side should be tightened to 17 foot pounds, the bolts to the transmission side should be tightened to 33 foot pounds.

You should be done, but the manual says to wait 30 minutes prior to adding oil.

Good luck!

May 15, 2008 | 1995 Honda Civic

Not finding what you are looking for?
2000 Mazda MPV Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...